Casio CFX-9850G PLUS Technical document

Appendix
Appendix A Resetting the Calculator
Appendix B Power Supply
Appendix C Error Message Table
Appendix D Input Ranges
Appendix E Specifications

430
Appendix A Resetting the Calculator
Warning!
The procedure described here clears all memory contents. Never perform this
operation unless you want to totally clear the memory of the calculator. If you
need the data currently stored in memory, be sure to write it down somewhere
before performing the RESET operation.
uu
uu
uTo reset the calculator
F
1. Highlight the MEM icon on the main menu and then press w, or press t.
2. Use cto move the highlighting down to “Reset” and then press w.
123456
3. Press 1(YES) to reset the calculator or 6(NO) to abort the operation
without resetting anything.
4. Press m.
P. 11 •If the display appears to dark or dim after you reset the calculator, adjust the
contrast.

431
•If the calculator stops operating correctly for
some reason, use a thin, pointed object to
press the P button on the back of the
calculator. This should make the RESET
screen appear on the display. Perform the
procedure to complete the RESET operation.
•Pressing the P button while an internal calculation is being performed will
cause all data in memory to be deleted.
Resetting the Calculator Appendix A
P button

432
Appendix B Power Supply
This calculator is powered by four AAA-size (LR03 (AM4) or R03 (UM-4))
batteries. In addition, it uses a single CR2032 lithium battery as a back up power
supply for the memory.
If the following message appears on the display, immediately turn off the calculator
and replace batteries.
If you try to continue using the calculator, it will automatically turn off in order to
protect memory contents. You will not be able to turn power back on until you
replace batteries.
Be sure to replace the main batteries at least once every two years, no matter how
much you use the calculator during that time.
The batteries that come with this calculator discharge slightly during shipment and
storage. Because of this, they may require replacement sooner than the normal
expected battery life.
Warning!
All memory contents will be deleted if you remove both the main power supply
and the memory back up batteries at the same time. If you ever remove both
batteries, correctly reload them and then perform the reset operation.
kk
kk
kReplacing Batteries
Precautions:
Incorrectly using batteries can cause them to burst or leak, possibly damaging the
interior of the calculator. Note the following precautions:
•Be sure that the positive (+) and negative (–) poles of each battery are facing in
the proper directions.
•Never mix batteries of different types.
•Never mix old batteries and new ones.
•Never leave dead batteries in the battery
compartment.
•Remove the batteries if you do not plan
to use the calculator for long periods.
•Never try to recharge the batteries
supplied with the calculator.
•Do not expose batteries to direct heat, let them become shorted, or try to take
them apart.

433
Power Supply Appendix B
(Should a battery leak, clean out the battery compartment of the calculator
immediately, taking care to avoid letting the battery fluid come into direct
contact with your skin.)
Keep batteries out of the reach of small children. If swallowed, consult with a
physician immediately.
uu
uu
uTo replace the main power supply batteries
*Never remove the main power supply and the memory back up batteries
from the calculator at the same time.
*Never turn on the calculator while the main power supply batteries are
removed or not loaded correctly. Doing so can cause memory data to be
deleted and malfunction of the calculator. If mishandling of batteries causes
such problems, correctly load batteries and then perform the RESET
operation to resume normal operation.
*Be sure to replace all four batteries with new ones.
1. Press !O to turn off the calculator.
Warning!
*Besure to turn the calculator off before replacing batteries. Replacing
batteries with power on will cause data in memory to be deleted.
2. Making sure that you do not accidently press the okey, attach the case to
the calculator and then turn it over.
3. Remove the back cover from the calculator by
pulling with your finger at the point marked 1.
4. Remove the four old batteries.
5. Load a new set of four batteries, making sure that
their positive (+) and negative (–) ends are facing in
the proper directions.
6. Replace the back cover.
7. Turn the calculator front side up and remove its case.
Next, press oto turn on power.
1
BACK UP

434
Appendix B Power Supply
•Power supplied by memory back up battery while the main power supply
batteries are removed for replacement retains memory contents.
•Do not leave the calculator without main power supply batteries loaded for long
periods. Doing so can cause deletion of data stored in memory.
•If the figures on the display appear too light and hard to see after you turn on
power, adjust the contrast.
uu
uu
uTo replace the memory back up battery
*Before replacing the memory back up battery, turn on the calculator and
check to see if the “Low battery!” message appears on the display. If it does,
replace the main power supply batteries before replacing the back up power
supply battery.
*Never remove the main power supply and the memory back up batteries
from the calculator at the same time.
*Be sure to replace the back up power supply battery at least once 2 years,
regardless of how much you use the calculator during that time. Failure to do
so can cause data in memory to be deleted.
1. Press !O to turn off the calculator.
Warning!
*Besure to turn the calculator off before replacing batteries. Replacing
batteries with power on will cause data in memory to be deleted.
2. Making sure that you do not accidently press the okey, attach the case to
the calculator and then turn it over.
3. Remove the back cover from the calculator by
pulling with your finger at the point marked 1.
4. Remove screw ion the back of the calculator, and
remove the back up battery compartment cover.
5. Insert a thin, pointed non-metal object
(such as a toothpick) into the hole maked j
and remove the old battery.
1
A
B
BACK UP

435
Power Supply Appendix B
6. Wipe off the surfaces of a new battery with a soft,
dry cloth. Load it into the calculator so that its positive
(+) side is facing up.
7. Install the memory protection battery cover onto the
calculator and secure it in place with the screw.
Next, replace the back cover.
8. Turn the calculator front side up and remove its case. Next, press oto turn
on power.
kk
kk
kAbout the Auto Power Off Function
Calculator power turns off automatically if you do not perform any key operation
for about 6 minutes. To restore power, press o.
BACK UP

436
Meaning
1Calculation formula contains an
error.
2Formula in a program contains
an error.
1Calculation result exceeds
calculation range.
2Calculation is outside the input
range of a function.
3Illogical operation (division by
zero, etc.)
4Poor precision in ∑calculation
results.
5Poor precision in differential
calculation results.
6Poor precision in integration
calculation results.
7Cannot find results of equation
calculations.
1No corresponding Lbl nfor
Goto n.
2No program stored in program
area Prog ”file name”.
•Nesting of subroutines by Prog
”file name” exceeds 10 levels.
Message
Syn ERROR
Ma ERROR
Go ERROR
Ne ERROR
Countermeasure
1Use dor eto display the
point where the error was
generated and correct it.
2Use dor eto display the point
where the error was generated
and then correct the program.
1234
Check the input numeric value
and correct it.
When using memories, check
that the numeric values stored
in memories are correct.
5Try using a smaller value for Ax
(xincrement/decrement).
6Try changing the tolerance “tol”
when using Gauss-Kronrod
Rule or the number of divisions
“n” when using Simpson's Rule
to another value.
7Check the coefficients of the
equation.
1Correctly input a Lbl nto corres-
pond to the Goto n, or delete
the Goto nif not required.
2Store a program in program
area Prog ”file name”, or delete
the Prog ”file name” if not
required.
•Ensure that Prog ”file name” is
not used to return from
subroutines to main routine. If
used, delete any unnecessary
Prog ”file name”.
•Trace the subroutine jump
destinations and ensure that no
jumps are made back to the
original program area. Ensure
that returns are made correctly.
Appendix C Error Message Table

Meaning
•Execution of calculations that
exceed the capacity of the
stack for numeric values or
stack for commands.
•Not enough memory to input a
function into function memory.
•Not enough memory to create a
matrix using the specified
dimension.
•Not enough memory to hold
matrix calculation result.
•Not enough memory to store
data in list function.
•Not enough memory to input
coefficient for equation.
•Not enough memory to hold
equation calculation result.
•Not enough memory to hold
function input in the Graph
Mode for graph drawing.
•Not enough memory to hold
function input in the DYNA
Mode for graph drawing.
•Not enough memory to hold
function or recursion input.
•Incorrect argument specification
for a command that requires an
argument.
•Illegal dimension or list used
during matrix calculations.
•Problem with cable connection
or parameter setting during
program data communications.
•Problem with cable connection
or parameter setting during
data communications.
•Problem with cable connection
or parameter setting during
data communications.
•Memory of receiving unit
became full during program
data communications.
Message
Stk ERROR
Mem ERROR
Arg ERROR
Dim ERROR
Com ERROR
Transmit
ERROR!
Receive
ERROR!
Memory Full!
Countermeasure
•Simplify the formulas to keep
stacks within 10 levels for the
numeric values and 26 levels
for the commands.
•Divide the formula into two or
more parts.
•Keep the number of variables
you use for the operation within
the number of variables
currently available.
•Simplify the data you are trying
to store to keep it within the
available memory capacity.
•Delete no longer needed data
to make room for the new data.
•Correct the argument.
•Lbl n, Goto n: n= integer from
0 through 9.
•Check matrix or list dimension.
•Check cable connection.
•Check cable connection.
•Check cable connection.
•Delete some data stored in the
receiving unit and try again.
437
Error Message Table Appendix C

438
Function
sinx
cosx
tanx
sin–1x
cos–1x
tan–1x
sinhx
coshx
tanhx
sinh–1x
cosh–1x
tanh–1x
logx
Inx
10x
ex
x
x2
1/x
3x
x
!
nPr
nCr
Pol (x, y)
Accuracy
As a rule,
accuracy is
±1 at the
10th digit.*
"
"
"
"
"
"
"
"
"
"
Notes
However, for tanx:
|x|
GG
GG
G 90(2n+1):DEG
|x|
GG
GG
G π/2(2n+1):RAD
|x|
GG
GG
G 100(2n+1):GRA
Input ranges
(DEG) |x| < 9 ×(109)°
(RAD) |x| < 5 ×107πrad
(GRA) |x| < 1 ×1010grad
|x| <1
|x| < 1 ×10100
|x| <230.2585092
|x| < 1 ×10100
|x| < 5 ×1099
1<x< 5 ×1099
|x| < 1
1 ×10–99 <x< 1 ×10100
–1 ×10100 < x< 100
–1 ×10100
< x<230.2585092
0 <x< 1 ×10100
|x| <1 ×1050
|x| < 1 ×10100, x
GG
GG
G
0
|x| < 1 ×10100
0 <x<69
(xis an integer)
Result < 1 ×10100
n, r(nand rare integers)
0 <r<n,
n< 1 ×1010
< 1 ×10100
x2+ y2
Appendix D Input Ranges
Internal
digits
15 digits
"
"
"
"
"
"
"
"
"
"