Casio fx-100AU PLUS User manual

E
fx-100AU PLUS
User’s Guide
CASIO Worldwide Education Website
http://edu.casio.com
CASIO EDUCATIONAL FORUM
http://edu.casio.com/forum/
RJA528037-001V01

Contents
Important Information ............................................................. 2
Sample Operations.................................................................. 2
Initializing the Calculator........................................................ 2
Safety Precautions .................................................................. 2
Handling Precautions.............................................................. 2
Removing the Hard Case........................................................ 3
Turning Power On and Off ...................................................... 3
Adjusting Display Contrast .................................................... 3
Key Markings ........................................................................... 3
Reading the Display ................................................................ 4
Using Menus ............................................................................ 5
Specifying the Calculation Mode ........................................... 5
Configuring the Calculator Setup .......................................... 5
Inputting Expressions and Values......................................... 7
Toggling Calculation Results ............................................... 10
Basic Calculations ................................................................ 10
Prime Factorization ............................................................... 14
Function Calculations ........................................................... 15
Complex Number Calculations (CMPLX) ............................ 18
Statistical Calculations (STAT)............................................. 19
Base-nCalculations (BASE-N)............................................. 23
Using VERIFY (VERIF)........................................................... 25
Vector Calculations (VECTOR)............................................. 26
Metric Conversion ................................................................. 29
Calculation Ranges, Number of Digits,
and Precision ......................................................................... 30
Errors...................................................................................... 32
Before Assuming Malfunction of the Calculator... ............. 33
Replacing the Battery............................................................ 33
Specifications ........................................................................ 34
Frequently Asked Questions................................................ 34
E-1

E-2
Important Information
• The displays and illustrations (such as key markings) shown in this User’s
Guide are for illustrative purposes only, and may differ somewhat from the
actual items they represent.
• The contents of this manual are subject to change without notice.
• In no event shall CASIO Computer Co., Ltd. be liable to anyone for special,
collateral, incidental, or consequential damages in connection with or
arising out of the purchase or use of this product and items that come with
it. Moreover, CASIO Computer Co., Ltd. shall not be liable for any claim of
any kind whatsoever by any other party arising out of the use of this product
and the items that come with it.
• Be sure to keep all user documentation handy for future reference.
Sample Operations
Sample operations in this manual are indicated by a icon. Unless
specifically stated, all sample operations assume that the calculator is in its
initial default setup. Use the procedure under “Initializing the Calculator” to
return the calculator to its initial default setup.
For information about the B, b, v, and Vmarks that are shown
in the sample operations, see “Configuring the Calculator Setup”.
Initializing the Calculator
Perform the following procedure when you want to initialize the calculator and
return the calculation mode and setup to their initial default settings. Note that
this operation also clears all data currently in calculator memory.
!9(CLR)3(All)=(Yes)
Safety Precautions
Battery
• Keep batteries out of the reach of small children.
• Use only the type of battery specified for this calculator in this manual.
Handling Precautions
• Even if the calculator is operating normally, replace the battery at least
once every two years.
A dead battery can leak, causing damage to and malfunction of the
calculator. Never leave a dead battery in the calculator.
• The battery that comes with the calculator discharges slightly during
shipment and storage. Because of this, it may require replacement
sooner than the normal expected battery life.
• Do not use an oxyride battery* or any other type of nickel-based
primary battery with this product. Incompatibility between such
batteries and product specifications can result in shorter battery life
and product malfunction.
• Avoid use and storage of the calculator in areas subjected to
temperature extremes, and large amounts of humidity and dust.
• Do not subject the calculator to excessive impact, pressure, or
bending.

E-3
• Never try to take the calculator apart.
• Use a soft, dry cloth to clean the exterior of the calculator.
• Whenever discarding the calculator or batteries, be sure to do so in
accordance with the laws and regulations in your particular area.
* Company and product names used in this manual may be registered
trademarks or trademarks of their respective owners.
Removing the Hard Case
Before using the calculator, slide its hard
case downwards to remove it, and then affix
the hard case to the back of the calculator as
shown in the illustration nearby.
Turning Power On and Off
Press Oto turn on the calculator.
Press 1A(OFF) to turn off the calculator.
Auto Power Off
Your calculator will turn off automatically if you do not perform any operation
for about 10 minutes. If this happens, press the Okey to turn the calculator
back on.
Adjusting Display Contrast
Display the CONTRAST screen by performing the following key operation:
1N(SETUP)c6(]CONT'). Next, use dand eto adjust
contrast. After the setting is the way you want, press A.
Important: If adjusting display contrast does not improve display readability,
it probably means that battery power is low. Replace the battery.
Key Markings
Pressing the 1or Skey followed by a second
key performs the alternate function of the second key.
The alternate function is indicated by the text printed
above the key.
The following shows what the different colors of the
alternate function key text mean.
If key marking text
is this color: It means this:
Yellow Press 1and then the key to access the
applicable function.
Red Press Sand then the key to input the
applicable variable, constant, or symbol.
Purple (or enclosed
in purple brackets)
Enter the CMPLX Mode to access the function.
Green (or enclosed in
green brackets)
Enter the BASE-N Mode to access the function.
sin–1 D
s
Alternate function
Keycap function
sin–1 D
s
Alternate function
Keycap function

E-4
Reading the Display
The display of the calculator shows expressions you input, calculation results,
and various indicators.
Input expression Indicators
Calculation result
• If a 'indicator appears on the right side of the calculation result, it means
the displayed calculation result continues to the right. Use eand dto
scroll the calculation result display.
• If a gindicator appears on the right side of the input expression, it means
the displayed calculation continues to the right. Use eand dto scroll the
input expression display. Note that if you want to scroll the input expression
while both the 'and gindicators are displayed, you will need to press A
first and then use eand dto scroll.
Display indicators
This
indicator: Means this:
S
The keypad has been shifted by pressing the 1key. The
keypad will unshift and this indicator will disappear when
you press a key.
A
The alpha input mode has been entered by pressing the
Skey. The alpha input mode will be exited and this
indicator will disappear when you press a key.
M There is a value stored in independent memory.
STO
The calculator is standing by for input of a variable name to
assign a value to the variable. This indicator appears after
you press 1t(STO).
RCL
The calculator is standing by for input of a variable name to
recall the variable’s value. This indicator appears after you
press t.
STAT The calculator is in the STAT Mode.
CMPLX The calculator is in the CMPLX Mode.
VCT The calculator is in the VECTOR Mode.
7 The default angle unit is degrees.
8 The default angle unit is radians.
9 The default angle unit is grads.
FIX A fixed number of decimal places is in effect.
SCI A fixed number of significant digits is in effect.
Math Natural Display is selected as the display format.
$`
Calculation history memory data is available and can be
replayed, or there is more data above/below the current
screen.
Math Math Math Math

E-5
Disp The display currently shows an intermediate result of a
multi-statement calculation.
Important: For some type of calculation that takes a long time to execute,
the display may show only the above indicators (without any value) while it
performs the calculation internally.
Using Menus
Some of the calculator’s operations are performed using menus. Pressing
Nor w, for example, will display a menu of applicable functions.
The following are the operations you should use to navigate between
menus.
• You can select a menu item by pressing the number key that corresponds
to the number to its left on the menu screen.
• The $indicator in the upper right corner of a menu means there is another
menu below the current one. The `indicator means another menu above.
Use cand fto switch between menus.
• To close a menu without selecting anything, press A.
Specifying the Calculation Mode
When you want to perform this type of
operation:
Perform this key
operation:
General calculations N1(COMP)
Complex number calculations N2(CMPLX)
Statistical and regression calculations N3(STAT)
Calculations involving specific number
systems (binary, octal, decimal, hexadecimal) N4(BASE-N)
Verify a calculation N5(VERIF)
Vector calculations N6(VECTOR)
Note: The initial default calculation mode is the COMP Mode.
Configuring the Calculator Setup
First perform the following key operation to display the setup menu:
1N(SETUP). Next, use cand fand the number keys to configure
the settings you want.
Underlined ( ___ ) settings are initial defaults.
1MthIO 2LineIO Specifies the display format.
Natural Display (MthIO) causes fractions,
irrational numbers, and other expressions to be
displayed as they are written on paper.
MthIO: Selects MathO or LineO. MathO displays
input and calculation results using the same format as they are written on
paper. LineO displays input the same way as MathO, but calculation results
are displayed in linear format.
Linear Display (LineIO) causes fractions and
other expressions to be displayed in a single
line.
MathMath

E-6
Note: • The calculator switches to Linear Display automatically whenever
you enter the STAT, BASE-N, or VECTOR Mode. • In this manual, the B
symbol next to a sample operation indicates Natural Display (LineO), while
the bsymbol indicates Linear Display.
3Deg 4Rad 5Gra Specifies degrees, radians or grads as the angle
unit for value input and calculation result display.
Note: In this manual, the vsymbol next to a sample operation indicates
degrees, while the Vsymbol indicates radians.
6Fix 7Sci 8Norm Specifies the number of digits for display of a
calculation result.
Fix: The value you specify (from 0 to 9) controls the number of decimal
places for displayed calculation results. Calculation results are rounded off
to the specified digit before being displayed.
Example: b100 ÷ 7 = 14.286 (Fix 3)
14.29 (Fix 2)
Sci: The value you specify (from 1 to 10) controls the number of significant
digits for displayed calculation results. Calculation results are rounded off to
the specified digit before being displayed.
Example: b1 ÷ 7 = 1.4286 × 10
–1
(Sci 5)
1.429 × 10
–1
(Sci 4)
Norm: Selecting one of the two available settings (Norm 1, Norm 2)
determines the range in which results will be displayed in non-exponential
format. Outside the specified range, results are displayed using exponential
format.
Norm 1: 10
–2
 |x|, |x|  10
10
Norm 2: 10
–9
 |x|, |x|  10
10
Example: b1 ÷ 200 = 5 × 10
–3
(Norm 1)
0.005 (Norm 2)
c1ab/c c2d/c Specifies either mixed fraction (ab/c) or improper
fraction (d/c) for display of fractions in calculation results.
c3CMPLX 1a+bi;2r∠Specifies either rectangular coordinates
(a+bi) or polar coordinates (r∠) for CMPLX Mode calculations.
c4STAT 1ON ; 2OFF Specifies whether or not to display a FREQ
(frequency) column in the STAT Mode Stat Editor.
c5Disp 1Dot ; 2Comma Specifies whether to display a dot or
a comma for the calculation result decimal point. A dot is always displayed
during input.
Note: When dot is selected as the decimal point, the separator for multiple
results is a comma (,). When comma is selected, the separator is a
semicolon (;).
c6]CONT'Adjusts display contrast. See “Adjusting Display
Contrast” for details.
Initializing Calculator Settings
Perform the following procedure to initialize the calculator, which returns the
calculation mode to COMP and returns all other settings, including setup
menu settings, to their initial defaults.
19(CLR)1(Setup)=(Yes)

E-7
Inputting Expressions and Values
Basic Input Rules
Calculations can be input in the same form as they are written. When you
press =the priority sequence of the input calculation will be evaluated
automatically and the result will appear on the display.
4 × sin30 × (30 + 10 × 3) = 120
4 *s30 )*( 30 +10 *3 )=
*
1
*
2
*
3
*
1
Input of the closing parenthesis is required for sin, sinh, and other functions
that include parentheses.
*
2
These multiplication symbols (×) can be omitted. A multiplication symbol
can be omitted when it occurs immediately before an opening parenthesis,
immediately before sin or other function that includes parentheses,
immediately before the Ran# (random number) function, or immediately
before a variable (A, B, C, D, E, F, M, X, Y), π or
e.
*
3
The closing parenthesis immediately before the =operation can be
omitted.
Input example omitting **
2
and )*
3
operations in the above
example.
4 s30 )( 30 +10 *3 =
Important: If you execute a calculation that includes both division and
multiplication operations in which a multiplication sign has been omitted,
parentheses will be inserted automatically as shown in the examples below.
• When a multiplication sign is omitted immediately before an open
parenthesis or after a closed parenthesis.
6 ÷ 2 (1 + 2) p6 ÷ (2 (1 + 2)) 6 ÷ A (1 + 2) p6 ÷ (A (1 + 2))
1 ÷ (2 + 3) sin(30) p1 ÷ ((2 + 3) sin(30))
• When a multiplication sign is omitted immediately before a variable, a
constant, etc.
6 ÷ 2πp6 ÷ (2π)2 ÷ 2'2 p2 ÷ (2'2) 4π÷ 2πp4π÷ (2π)
• When inputting a function that uses commas (such as Pol, Rec, and
RanInt#), be sure to input the closed parentheses required by the
expression. If you do not input closed parentheses, parentheses may not
be inserted automatically as described above.
Important: If you execute a calculation in which a multiplication sign has been
omitted immediately before a fraction (including mixed fractions), parentheses
will be inserted automatically as shown in the examples below.
1
2 × 3: B
'1 c3 dddd 2
=
MathMath
MathMath
MathMath
MathMath

E-8
4
sin(30) × 5: B
'4 c5 dddds30 )
=
Note: • If the calculation becomes longer than the screen width during
input, the screen will scroll automatically to the right and the ]indicator will
appear on the display. When this happens, you can scroll back to the left by
using dand eto move the cursor. • When Linear Display is selected,
pressing fwill cause the cursor to jump to the beginning of the calculation,
while cwill jump to the end. • When Natural Display is selected, pressing
ewhile the cursor is at the end of the input calculation will cause it to jump
to the beginning, while pressing dwhile the cursor is at the beginning will
cause it to jump to the end. • You can input up to 99 bytes for a calculation.
Each numeral, symbol, or function normally uses one byte. Some functions
require three to 13 bytes. • The cursor will change shape to kwhen there are
10 bytes or less of allowed input remaining. If this happens, end calculation
input and then press =.
Calculation Priority Sequence
The priority sequence of input calculations is evaluated in accordance with the
rules below. When the priority of two expressions is the same, the calculation
is performed from left to right.
1st Parenthetical expressions
2nd Functions that require an argument to the right and a closing
parenthesis “)” following the argument.
3rd Functions that come after the input value (
x2 , x3 , x–1 , x!, °’ ”, °,
r
,
g
,
%), powers (
x^), roots (")
4th Fractions
5th
Negative sign (–), base-nsymbols (d, h, b, o)
Note: When squaring a negative value (such as –2), the value
being squared must be enclosed in parentheses ((-2 )w
=). Since
x2 has a higher priority than the negative sign,
inputting -2 w=would result in the squaring of 2 and then
appending a negative sign to the result. Always keep the priority
sequence in mind, and enclose negative values in parentheses
when required.
6th Metric conversion commands (cm 'in, etc.),
STAT Mode estimated values (m, n, m1
, m2 )
7th Multiplication where the multiplication sign is omitted
8th Permutation (nPr), combination (nCr), complex number polar
coordinate symbol ( ∠)
9th Dot product ( • )
10th Multiplication, division (×, ÷)
11th Addition, subtraction (+, –)
12th Logical AND (and)
13th Logical OR, XOR, XNOR (or, xor, xnor)
MathMath
MathMath

E-9
Inputting with Natural Display
Selecting Natural Display makes it possible to input and display fractions
and certain functions (
x2 , x3 , x^, ), #, ", x−1 , 10^, e^, Abs) just as they
are written in your textbook.
2 + '
2
1 + ' 2
B
'2 +!2 ee 1 +!2 =
Important: • Certain types of expressions can cause the height of a
calculation formula to be greater than one display line. The maximum
allowable height of a calculation formula is two display screens (31 dots × 2).
Further input will become impossible if the height of the calculation you are
inputting exceeds the allowable limit. • Nesting of functions and parentheses
is allowed. Further input will become impossible if you nest too many functions
and/or parentheses. If this happens, divide the calculation into multiple parts
and calculate each part separately.
Note: When you press =and obtain a calculation result using Natural
Display, part of the expression you input may be cut off. If you need to view
the entire input expression again, press Aand then use dand eto
scroll the input expression.
Using Values and Expressions as Arguments
(Natural Display only)
A value or an expression that you have already input can be used as the
argument of a function. After you have input 7
6, for example, you can make
it the argument of ', resulting in 7
6
'
.
To input 1 + 7
6and then change it to 1 + 7
6
'
B
1 +7 '6
dddd1Y(INS)
!
As shown above, the value or expression to the right of the cursor after
1Y(INS) are pressed becomes the argument of the function that is
specified next. The range encompassed as the argument is everything up
to the first open parenthesis to the right, if there is one, or everything up to
the first function to the right (sin(30), log(4), etc.)
This capability can be used with the following functions: ', 16("),
1l($), 1i(%), !, 6, 1!(#), D.
MathMath
MathMath
MathMath
MathMath

E-10
Overwrite Input Mode (Linear Display only)
You can select either insert or overwrite as the input mode, but only while
Linear Display is selected. In the overwrite mode, text you input replaces the
text at the current cursor location. You can toggle between the insert and
overwrite modes by performing the operations: 1Y(INS). The cursor
appears as “
I” in the insert mode and as “ ” in the overwrite mode.
Note: Natural Display always uses the insert mode, so changing display
format from Linear Display to Natural Display will automatically switch to
the insert mode.
Correcting and Clearing an Expression
To delete a single character or function: Move the cursor so it is directly to
the right of the character or function you want to delete, and then press Y.
In the overwrite mode, move the cursor so it is directly under the character
or function you want to delete, and then press Y.
To insert a character or function into a calculation: Use dand eto
move the cursor to the location where you want to insert the character or
function and then input it. Be sure always to use the insert mode if Linear
Display is selected.
To clear all of the calculation you are inputting: Press A.
Toggling Calculation Results
Each press of fwill toggle the currently displayed calculation result between
its decimal form and fraction form.
1 ÷ 5 = 1
5= 0.2 B
1 /5 =0.2 f1
5
1 ÷ 5 = 0.2 = 1
5b
1 /5 =
0.2 f1{5
1 –
4
5= 1 5= 0.2 b
1 -4 '5 =
1{5 f0.2
Important: • With certain calculation results, pressing the fkey will not
convert the displayed value. • You cannot switch from decimal form to
mixed fraction form if the total number of digits used in the mixed fraction
(including integer, numerator, denominator, and separator symbols) is
greater than 10.
Note: With Natural Display (MathO), pressing 1=instead of =after
inputting a calculation will display the calculation result in decimal form.
Basic Calculations
Fraction Calculations
Note that the input method for fractions is different, depending upon whether
you are using Natural Display or Linear Display.

E-11
2 + 1 = 7
3 2 6 B2 '3 e+1 '2 =7
6
or '2 c3 e+'1 c2 =7
6
b2 '3 +1 '2 =7{6
1 = 1
2 2
4 − 3 B4 -1'(() 3 e1 c2 =1
2
b4 -3 '1 '2 =1{2
Note: • Mixing fractions and decimal values in a calculation while Linear
Display is selected will cause the result to be displayed as a decimal value.
• Fractions in calculation results are displayed after being reduced to their
lowest terms.
To switch a calculation result between improper fraction and mixed
fraction form: Perform the following key operation: 1f(
<
)
To switch a calculation result between fraction and decimal form:
Press f.
Percent Calculations
Inputting a value and pressing 1((%) causes the input value to become
a percent.
150 × 20% = 30 150 *20 1((%)=30
Calculate what percentage of 880 is 660. (75%)
660 /880 1((%)=75
Increase 2500 by 15%. (2875)
2500 +2500 *15 1((%)=
2875
Discount 3500 by 25%. (2625)
3500 -3500 *25 1((%)=
2625
Degree, Minute, Second (Sexagesimal) Calculations
Performing an addition or subtraction operation between sexagesimal values,
or a multiplication or division operation between a sexagesimal value and a
decimal value will cause the result to be displayed as a sexagesimal value.
You also can convert between sexagesimal and decimal. The following
is the input format for a sexagesimal value: {degrees} ${minutes} $
{seconds} $.
Note: You must always input something for the degrees and minutes, even
if they are zero.
2°20´30˝ + 39´30˝ = 3°00´00˝
2 $20 $30 $+0 $39 $30 $=
3°0´0˝
Convert 2°15´18˝ to its decimal equivalent.
2 $15 $18 $=
2°15´18˝
(Converts sexagesimal to decimal.) $2.255
(Converts decimal to sexagesimal.) $2°15´18˝

E-12
Multi-Statements
You can use the colon character (:) to connect two or more expressions and
execute them in sequence from left to right when you press =.
3 + 3 : 3 ×3 3 +3 SW(:) 3 *3 =6
=9
Using Engineering Notation
A simple key operation transforms a displayed value to engineering
notation.
Transform the value 1234 to engineering notation, shifting the
decimal point to the right.
1234 =
1234
W1.234×10
3
W1234×10
0
Transform the value 123 to engineering notation, shifting the decimal
point to the left.
123 =
123
1W(←) 0.123×10
3
1W(←) 0.000123×10
6
Calculation History
In the COMP, CMPLX, or BASE-N Mode, you can scroll through calculation
history contents using fand c.
1 + 1 = 2 1 +1 =2
2 + 2 = 4 2 +2 =4
3 + 3 = 6 3 +3 =6
(Scrolls back.) f4
(Scrolls back again.) f2
Note: Calculation history data is all cleared whenever you press O, when
you change to a different calculation mode, when you change the display
format, or whenever you perform any reset operation.
Replay
While a calculation result is on the display, you can press dor eto edit
the expression you used for the previous calculation.
4 × 3 + 2.5 = 14.5 b4 *3 +2.5 =14.5
4 × 3 − 7.1 = 4.9 (Continuing) dYYYY-7.1 =4.9
Note: If you want to edit a calculation when the 'indicator is on the right
side of a calculation result display (see “Reading the Display”), press A
and then use dand eto scroll the calculation.

E-13
Answer Memory (Ans)/Previous Answer Memory
(PreAns)
The last calculation result obtained is stored in Ans (answer) memory. The
calculation result obtained prior to the last one is stored in PreAns (previous
answer) memory. Displaying the result of a new calculation will move current
Ans memory contents to PreAns memory and store the new calculation
results in Ans memory. PreAns memory can be used only in the COMP
Mode. PreAns memory contents are cleared whenever the calculator enters
another mode from the COMP Mode.
To divide the result of 3 × 4 by 30 b
3 *4 =
(Continuing) /30 =
123 + 456 = 579 B
123 +456 =
789 – 579 = 210
(Continuing) 789 -G=
For Tk+2 = Tk+1 + Tk(Fibonacci sequence), determine the sequence
from T1to T5. Note however, that T1 = 1 and T2 = 1. B
T
1 = 1 1 =
(Ans = T1= 1)
T
2 = 1 1 =
(Ans = T2= 1, PreAns = T1= 1)
T
3 = T2+ T1 = 1 + 1
G+SG(PreAns)=
(Ans = T3= 2, PreAns = T2= 1)
T
4 = T3+ T2 = 2 + 1 =
(Ans = T4= 3, PreAns = T3= 2)
T
5 = T4+ T3 = 3 + 2 =
Result: The sequence is {1, 1, 2, 3, 5}.
MathMath
MathMath
MathMath
MathMath
MathMath
MathMath

E-14
Variables (A, B, C, D, E, F, X, Y)
Your calculator has eight preset variables named A, B, C, D, E, F, X, and Y. You
can assign values to variables and also use the variables in calculations.
To assign the result of 3 + 5 to variable A
3 +5 1t(STO)y(A)
8
To multiply the contents of variable A by 10
(Continuing) Sy(A)*10 =
80
To recall the contents of variable A (Continuing) ty(A) 8
To clear the contents of variable A 0 1t(STO)y(A) 0
Independent Memory (M)
You can add calculation results to or subtract results from independent
memory. The “M” appears on the display when there is any value other than
zero stored in independent memory.
To clear the contents of M 0 1t(STO)l(M) 0
To add the result of 10 × 5 to M (Continuing) 10 *5 l50
To subtract the result of 10 + 5 from M
(Continuing) 10 +5 1l(M–) 15
To recall the contents of M (Continuing) tl(M) 35
Note: Variable M is used for independent memory.
Clearing the Contents of All Memories
Ans memory, independent memory, and variable contents are retained even
if you press A, change the calculation mode, or turn off the calculator.
PreAns memory contents are retained even if you press Aand turn off the
calculator without exiting the COMP Mode. Perform the following procedure
when you want to clear the contents of all memories.
!9(CLR)2(Memory)=(Yes)
Prime Factorization
In the COMP Mode, you can factor a positive integer up to 10 digits into
prime factors up to three digits.
To perform prime factorization on 1014
1014 =
!e(FACT)
When you perform prime factorization on a value that includes a factor that
is prime number with more than three digits, the part that cannot be factored
will be enclosed in parentheses on the display.
To perform prime factorization on 4104676 (= 22×10132)
4104676 =!e(FACT)

E-15
Any one of the following operations will exit prime factorization result
display.
• Pressing !e(FACT) or =.
• Pressing any of the following keys: .or e.
• Using the setup menu to change the angle unit setting (Deg, Rad, Gra) or
the display digits setting (Fix, Sci, Norm).
Note: • You will not be able to execute prime factorization while a decimal
value, fraction, or negative value calculation result is displayed. Trying to
do so will cause a math error (Math ERROR). • You will not be able to
execute prime factorization while the result of a calculation that uses Pol,
Rec, is displayed.
Function Calculations
For actual operations using each function, see the “Examples” section
following the list below.
π
π
: π is displayed as 3.141592654, but π = 3.14159265358980 is used for
internal calculations.
e : e is displayed as 2.718281828, but e = 2.71828182845904 is used for
internal calculations.
sin, cos, tan, sin
−1
, cos
−1
, tan
−1
: Trigonometric functions. Specify the
angle unit before performing calculations. See 1.
sinh, cosh, tanh, sinh
−1
, cosh
−1
, tanh
−1
: Hyperbolic functions. Input a
function from the menu that appears when you press w. The angle unit
setting does not affect calculations. See 2.
°,
r
,
g
: These functions specify the angle unit. ° specifies degrees,
r
radians,
and
g
grads. Input a function from the menu that appears when you perform
the following key operation: 1G(DRG'). See 3.
$, % : Exponential functions. Note that the input method is different
depending upon whether you are using Natural Display or Linear Display.
See 4.
log
: Logarithmic function. See 5.
ln : Natural logarithm to base e. See 6.
x2, x3, x^, ),#,",x−1 :Powers, power roots, and reciprocals. Note
that the input methods for x^, ), #, and "are different depending upon
whether you are using Natural Display or Linear Display. See 7.
Note: The following functions cannot be input in consecutive sequence: x2,
x3, x^, x−1. If you input 2ww, for example, the final wwill be ignored. To
input 2
2
2, input 2w, press the dkey, and then press w(B).
Pol, Rec :Pol converts rectangular coordinates to polar coordinates, while
Rec converts polar coordinates to rectangular coordinates. See 8.
Pol(
x, y) = (r, ) Rec(r, ) = (x, y)
Rectangular Polar
Coordinates (Rec) Coordinates (Pol)
Specify the angle unit before
performing calculations.
The calculation result for rand 
and for xand yare each assigned
respectively to variables X and Y.
Calculation result
θ is displayed
in the range of −180° 
θ 
180°.
Specify the angle unit before
performing calculations.
The calculation result for rand 
and for xand yare each assigned
respectively to variables X and Y.
Calculation result
θ is displayed
in the range of −180° 
θ 
180°.

E-16
x!:Factorial function. See 9.
Abs :Absolute value function. Note that the input method is different
depending upon whether you are using Natural Display or Linear Display.
See 10 .
Ran# :Generates a 3-digit pseudo random number that is less than 1. The
result is displayed as a fraction when Natural Display is selected. See 11 .
RanInt# :For input of the function of the form RanInt#(a, b), which generates
a random integer within the range of ato b. See 12 .
nPr, nCr:Permutation (nPr) and combination (nCr) functions. See 13 .
Rnd :The argument of this function is made a decimal value and then rounded
in accordance with the current number of display digits setting (Norm, Fix, or
Sci). With Norm 1 or Norm 2, the argument is rounded off to 10 digits. With
Fix and Sci, the argument is rounded off to the specified digit. When Fix 3
is the display digits setting, for example, the result of 10 ÷ 3 is displayed
as 3.333, while the calculator maintains a value of 3.33333333333333 (15
digits) internally for calculation. In the case of Rnd(10÷3) = 3.333 (with Fix
3), both the displayed value and the calculator’s internal value become
3.333. Because of this a series of calculations will produce different results
depending on whether Rnd is used (Rnd(10÷3) ×3 = 9.999) or not used (10
÷ 3 × 3 = 10.000). See 14 .
GCD, LCM :GCD determines the greatest common divisor of two values,
while LCM determines the least common multiple. See 15 .
Note: Using functions can slow down a calculation, which may delay display
of the result. Do not perform any subsequent operation while waiting for the
calculation result to appear. To interrupt an ongoing calculation before its
result appears, press A.
Examples
sin 30°= 0.5 bv s30 )= 0.5
sin
−1
0.5 = 30° bv 1s(sin
−1
) 0.5 )= 30
sinh 1 = 1.175201194 wb(sinh) 1 )= 1.175201194
cosh
–1
1 = 0 wf(cosh
−1
) 1 )= 0
π /2 radians = 90°, 50 grads = 45° v
(15(π)/2 )1G(DRG')c(
r
)=90
50 1G(DRG')d(
g
)=45
To calculate e5 × 2 to three significant digits (Sci 3)
1N(SETUP)7(Sci)3
B1i(%) 5 e*2 =
2.97×10
2
b1i(%) 5 )* 2 =2.97×10
2
log
10
1000 = log 1000 = 3 l1000 )= 3
To calculate ln 90 (= log
e
90) to three significant digits (Sci 3)
1N(SETUP)7(Sci)3i90 )= 4.50×10
0
11
22
33
44
55
66

E-17
1.2 × 10
3
= 1200 B1.2 *10 63 =1200
(1+1)
2+2
= 16 B(1 +1 )62 +2 =16
(52)3= 15625 (5 x)W=15625
32
5= 2 B16(") 5 e32 =2
b516(") 32 )= 2
To calculate '
2 × 3(= 4.242640687...) to three decimal places (Fix 3)
1N(SETUP)6(Fix)3B!2 e*3 =4.243
b!2 )*3 =4.243
To convert rectangular coordinates ('
2, ' 2) to polar coordinates
v
B1+(Pol)!2 e1)(,)!2 e)=
r=2,=45
b1+(Pol)!2 )1)(,)!2 ))=r= 2
 = 45
To convert polar coordinates ('
2, 45°) to rectangular coordinates
v
B1-(Rec)!2 e1)(,) 45 )=
X=1, Y=1
(5 + 3) ! = 40320 (5 +3 )q=40320
|2 – 7| × 2 = 10
BD2 -7 e*2 =
10
bD2 -7 )*2 =10
To obtain three random three-digit integers
1000 1.(Ran#)=459
=48
=117
(Results shown here are for illustrative purposes only. Actual results will differ.)
To generate random integers in the range of 1 to 6
S.(RanInt) 1 1)(,) 6 )= 2
=6
=1
(Results shown here are for illustrative purposes only. Actual results will differ.)
To determine the number of permutations and combinations
possible when selecting four people from a group of 10
Permutations: 10 1*(nPr) 4 =5040
Combinations: 10 1/(nCr) 4 =210
To perform the following calculations when Fix 3 is selected for the
number of display digits: 10 ÷ 3 × 3 and Rnd(10 ÷ 3) × 3 b
1N(SETUP)6(Fix)310 /3 *3 =10.000
10(Rnd) 10 /3 )* 3 =9.999
77
88
99
1010
1111
1212
1313
1414

E-18
To determine the greatest common divisor of 28 and 35
S*(GCD) 28 1)(,) 35 )= 7
To determine the least common multiple of 9 and 15
S/(LCM) 9 1)(,) 15 )= 45
Complex Number Calculations (CMPLX)
To perform complex number calculations, first press N2(CMPLX) to
enter the CMPLX Mode. You can use either rectangular coordinates (a+bi)
or polar coordinates (r∠) to input complex numbers. Complex number
calculation results are displayed in accordance with the complex number
format setting on the setup menu.
(2 + 6i) ÷ (2i) = 3 – i(Complex number format: a + bi)
(2 +6 W(i))/( 2 W(i))= 3–i
'
2∠ 45 = 1 + iBv (Complex number format: a + bi)
!2 e1-(∠) 45 =1+i
'
2+ ' 2i= 2 ∠ 45 Bv (Complex number format: r∠)
!2 e+!2 eW(i)=2∠45
Note: • If you are planning to perform input and display of the calculation
result in polar coordinate format, specify the angle unit before starting the
calculation. • The value of the calculation result is displayed in the range
of –180°   180°. • Display of the calculation result while Linear Display
is selected will show aand bi(or rand ) on separate lines.
CMPLX Mode Calculation Examples
(1 – i)–1 = 1
2
1
2
+ iB(Complex number format: a + bi)
(1 -W(i))E=1
2
1
2
+i
(1 + i)4+ (1 – i)2= – 4 – 2iB
(1 +W(i))64 e+( 1 -W(i))w=–4–2i
To obtain the conjugate complex number of 2 + 3i(Complex number
format: a + bi)
12(CMPLX)2(Conjg) 2 +3 W(i))= 2–3i
To obtain the absolute value and argument of 1 + iBv
Absolute Value: D1 +W(i)=1.414213562
Argument: 12(CMPLX)1(arg)1+W(i))= 45
Using a Command to Specify the Calculation Result
Format
Either of two special commands ('r∠or 'a+bi) can be input at the end
of a calculation to specify the display format of the calculation results. The
command overrides the calculator’s complex number format setting.
1515

E-19
'
2+ ' 2i= 2 ∠ 45, ' 2∠ 45 = 1 + iBv
!2 e+!2 eW(i)12(CMPLX)3('r∠)=2∠45
!2 e1-(∠) 45 12(CMPLX)4('a+bi)=1+i
Statistical Calculations (STAT)
To start a statistical calculation, perform the key operation N3(STAT)
to enter the STAT Mode and then use the screen that appears to select the
type of calculation you want to perform.
To select this type of statistical calculation:
(Regression formula shown in parentheses) Press this key:
Single-variable (X) 1(1-VAR)
Paired-variable (X, Y), linear regression (
y = A + Bx) 2(A+BX)
Paired-variable (X, Y), quadratic regression
( y = A + Bx + Cx2 ) 3( _+CX
2
)
Paired-variable (X, Y), logarithmic regression
(
y = A + Blnx) 4(ln X)
Paired-variable (X, Y),
e exponential regression
(
y = AeB
x) 5(
e^X)
Paired-variable (X, Y),
ab exponential regression
(
y = AB
x
) 6(A
•B^X)
Paired-variable (X, Y), power regression (
y = AxB ) 7(A
•X^B)
Paired-variable (X, Y), inverse regression
(
y = A + B/x) 8(1/X)
Pressing any of the above keys (1to 8) displays the Stat Editor.
Note: When you want to change the calculation type after entering the
STAT Mode, perform the key operation 11(STAT)1(Type) to display
the calculation type selection screen.
Inputting Data
Use the Stat Editor to input data. Perform the following key operation to
display the Stat Editor: 11(STAT)2(Data).
The Stat Editor provides 40 rows for data input when there is an X column
only or when there are X and Y columns, 20 rows when there are X and FREQ
columns, or 26 rows when there are X, Y, and FREQ columns.
Note: Use the FREQ (frequency) column to input the quantity (frequency) of
identical data items. Display of the FREQ column can be turned on (displayed)
or off (not displayed) using the Stat Format setting on the setup menu.
To select linear regression and input the following data:
(170, 66), (173, 68), (179, 75)
N3(STAT)2(A+BX)
11
STATSTAT