Casio ClassPad 330 Installation manual

ClassPad 330
ClassPad OS Version 3.06
Hardware
User’s Guide
E
CASIO Education website URL
http://edu.casio.com
ClassPad website URL
http://edu.casio.com/products/classpad/
ClassPad register URL
http://edu.casio.com/dl/

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not
applicable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Proper connectors must be used for connection to host computer and/or peripherals in order to
meet FCC emission limits.
Connector SB-62 ClassPad to ClassPad
USB connector for the ClassPad ClassPad to Windows®compatible PC
Fugue ©1999 – 2002 Kyoto Software Research, Inc. All rights reserved.
Company and product names used in this manual may be registered trademarks or trademarks
of their respective owners.
Declaration of Conformity
Model Number: ClassPad 330
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

20110401
Contents
Chapter 1 Getting Ready
1-1 Unpacking ............................................................................................. 1-1-1
1-2 Attaching and Removing the Front Cover ......................................... 1-2-1
1-3 Using the Stylus ................................................................................... 1-3-1
1-4 Replacing Batteries and Setting Up the ClassPad ............................ 1-4-1
1-5 User Registration ................................................................................. 1-5-1
1-6 Handling Precautions .......................................................................... 1-6-1
1-7 Adjusting Display Contrast ................................................................. 1-7-1
1-8 Configuring Power Properties ............................................................ 1-8-1
Power Saving Mode ...........................................................................................1-8-1
Auto Power Off ..................................................................................................1-8-1
Configuring Power Properties.............................................................................1-8-2
1-9 Optimizing “Flash ROM” ...................................................................... 1-9-1
1-10 Specifying the Ending Screen Image ............................................... 1-10-1
1-11 Adjusting Touch Panel Alignment ................................................... 1-11-1
Chapter 2 Performing Data Communication
2-1 Data Communication Overview .......................................................... 2-1-1
Connectable Devices and Transferable Data.....................................................2-1-1
Using the ClassPad Communication Application ...............................................2-1-3
2-2 Connecting the ClassPad to Another Device .................................... 2-2-1
Connecting to Another ClassPad Unit ................................................................2-2-1
Connecting to an EA-200 Data Analyzer............................................................2-2-2
Connecting to a Computer (USB).......................................................................2-2-3
2-3 Configuring Communication Parameters ........................................... 2-3-1
Wakeup ..............................................................................................................2-3-2
2-4 Transferring Data to Another ClassPad Unit ..................................... 2-4-1
Selecting Data for Transfer.................................................................................2-4-3
Sending a Screenshot of the Current Display Contents .....................................2-4-5
Communication Standby ....................................................................................2-4-6
Interrupting an Ongoing Data Communication Operation ..................................2-4-6
Appendix
1 Resetting and Initializing the ClassPad .............................................. α-1-1
2 Deleting an Application ........................................................................ α-2-1
3 Power Supply......................................................................................... α-3-1
4 Number of Digits and Precision........................................................... α-4-1
5 Specifications........................................................................................ α-5-1
1
Contents

20110401
Getting Ready
This section contains important information you need to know before
using the ClassPad for the first time.
1-1 Unpacking
1-2 Attaching and Removing the Front Cover
1-3 Using the Stylus
1-4 Replacing Batteries and Setting Up the ClassPad
1-5 User Registration
1-6 Handling Precautions
1-7 Adjusting Display Contrast
1-8 Configuring Power Properties
1-9 Optimizing “Flash ROM”
1-10 Specifying the Ending Screen Image
1-11 Adjusting Touch Panel Alignment
Chapter
1

20110401
1-1 Unpacking
When unpacking your ClassPad, check to make sure that all of the items shown here are
included. If anything is missing, contact your original retailer immediately.
Quick Start Guide
ClassPad
Stylus (Inserted in ClassPad.)
CD-ROM
3-pin Cable (SB-62)
Front Cover
(Attached to
ClassPad.)
USB Cable
.
7
4
1
0
23
56
89
=
(
)
,
(–)
xz
^
y
쎹
÷
−
+
EXE
EXP
Keyboard
ON/OFF
Clear
Touch Screen Protector Four AAA-size Batteries LR03
(AM4)
(The protector is already installed
on the touch screen when you
purchase the ClassPad.)
ClassPad website URL
http://edu.casio.com/products/classpad/
EEE Yönetmeli¤ine Uygundur
Quick Start Guide
ClassPad 330
CASIO Education website URL
http://edu.casio.com
E
ClassPad register URL
http://edu.casio.com/dl/
Quick Start Guide
ClassPad
Stylus (Inserted in ClassPad.)
CD-ROM
3-pin Cable (SB-62)
Front Cover
(Attached to
ClassPad.)
USB Cable
.
7
4
1
0
23
56
89
=
(
)
,
(–)
xz
^
y
쎹
÷
−
+
EXE
EXP
Keyboard
ON/OFF
Clear
Touch Screen Protector Four AAA-size Batteries LR03
(AM4)
(The protector is already installed
on the touch screen when you
purchase the ClassPad.)
ClassPad website URL
http://edu.casio.com/products/classpad/
EEE Yönetmeli¤ine Uygundur
Quick Start Guide
ClassPad 330
CASIO Education website URL
http://edu.casio.com
E
ClassPad register URL
http://edu.casio.com/dl/
1-1-1
Unpacking

20110401
1-2 Attaching and Removing the Front Cover
uTo remove the front cover
Before using the ClassPad, remove the front cover and attach it to the back.
uTo attach the front cover
When you are not using the ClassPad, attach the front cover to the front.
Important!
• Always attach the front cover to the ClassPad whenever you are not using it. Otherwise,
accidental operation of the touch screen or the okey can cause the power to turn on and
run down the batteries.
1-2-1
Attaching and Removing the Front Cover

20110401
1-3 Using the Stylus
Slide the stylus from the slot provided for it on the ClassPad, and then use it to perform touch
panel operations.
Important!
• Be careful so that you do not misplace or lose the stylus. When you are not using it, always
keep the stylus in the slot provided for it on the ClassPad.
• Be careful so that you do not damage the tip of the stylus. A damaged tip can scratch or
otherwise damage the ClassPad touch panel.
• Use only the supplied stylus or a similar instrument to perform touch panel operations. Never
use a pen, pencil, or other writing instrument.
1-3-1
Using the Stylus

20110401
1-4 Replacing Batteries and Setting Up the
ClassPad
Precautions:
Incorrectly using batteries can cause them to burst or leak, possibly damaging the interior of the
ClassPad. Note the following precautions:
• Be sure that the positive (+) and negative (–) poles of each battery are facing in the proper
directions.
• Never mix batteries of different types.
• Never mix old batteries and new ones.
• Never leave dead batteries in the battery
compartment.
• Remove the batteries if you do not plan to use
the ClassPad for long periods.
• Never try to recharge the batteries supplied with
the ClassPad.
• Do not expose batteries to direct heat, let them become shorted, or try to take them apart.
(Should a battery leak, clean out the battery compartment of the ClassPad immediately, taking
care to avoid letting the battery fluid come into direct contact with your skin.)
Keep batteries out of the reach of small children. If swallowed, consult with a physician
immediately.
uClassPad Operation
(1) Making sure that you do not accidentally press the okey, attach the front cover to the
ClassPad and then turn the ClassPad over. Remove the battery cover from the ClassPad by
pulling with your finger at the point marked 1.
P
1
(2) Load the four batteries that come with ClassPad.
• Make sure that the positive (+) and negative (–) ends of
the batteries are facing correctly.
1-4-1
Replacing Batteries and Setting Up the ClassPad

20110401
(3) Replace the battery cover, making sure that its tabs enter
the holes marked 2and turn the ClassPad front side up.
(4) Remove the front cover from the ClassPad.
(5) Align the touch panel.
a. Your ClassPad should turn on automatically and display
the Touch Panel Alignment screen.
b. Tap the center of each of the four cross marks as they
appear on the display.
• If the Touch Panel Alignment screen does not appear,
use the stylus to press the P button on the back of the
ClassPad.
Important!
• It may take a little time for your ClassPad to start up after
you press the P button.
P
P button
1-4-2
Replacing Batteries and Setting Up the ClassPad

20110401
(6) Adjust the display contrast.
a. Tap the button to make contrast darker, or the
button to make it lighter.
b. After the contrast setting is the way you want, tap [Set].
• Tapping [Initial] on the Contrast dialog box returns contrast to its initial factory default
setting.
(7) Specify the display language.
a. On the list that appears, tap the language you want to use.
• You can select German, English, Spanish, French, or
Portuguese.
b. When the language you want is selected, tap [Set].
• Tapping [Cancel] selects English and advances to the next dialog box.
(8) Specify the soft keyboard key arrangement.
a. On the list that appears, tap the key arrangement you
want to use.
b. When the key arrangement you want is selected, tap [Set].
• Tapping [Cancel] selects QWERTY arrangement and advances to the next dialog box.
1-4-3
Replacing Batteries and Setting Up the ClassPad