Castel XELLIP XEMED-P User manual

AUDIOVIDEOIPWASHABLEMASTERSTATION
Range: INTERCOM OVER IP
Series:
Installation Connection Programming Use
Technical data sheet no. EN-604-0008G
www.castel.fr
Page 1 / 8
PRESENTATION
Product references: 540.4000 - 540.4100 (WIFI) –540.4300 (4B)
The XELLIP washable master station with easy clean surface is part of a complete,
powerful Full IP multimedia system. With native SIP, it includes the following functions
(according to the version):
Set up Audio/Video over IP communication
Recording on SIP server (option of configuring up to two backup servers)
Managing a 12-button keypad and function keys (line tap, end call, directory, call on
hold, etc.)
Managing a 128x64-pixel graphic display.
Managing 1 to 4 programmable function buttons
Managing an "on-off" input
Managing a single-pole dry contact to control a keeper or other organ
Managing automatisms developed on the interfaces (time and logic relations)
Self tests (automatically or on request)
Update by TFTP.
Integrate SNMP protocol (Simple Network Management Protocol)
Integrate VLANs
Secure the Ethernet network by using the 802.1X protocol (Radius)
Backup on power failure.
The PoE (Power over Ethernet) function
The Wi-Fi function is available (optional)
Thanks to its embedded web server, it can be configured, monitored and operated
from any browser
VERSIONS
The standard version of the washable master station can be powered by POE (Power over
Ethernet)
Wi-Fi functionality optional
4 push button version without keyboard and display

AUDIOVIDEOIPWASHABLEMASTERSTATION
Technical data sheet no. EN-604-0008G
www.castel.fr
Page 2 / 8
CONNECTION
15-30VDCPower supply
RJ45: ETHERNET & 10/100 POE
USB (NC) Logic input Relayoutput
Reset Button
Amplifier connection
or magnétic induction loop
RTE C
NO NF C
Power supply connection
The station requires a power supply of 15 V to 30 V.
Comment: the station can be powered by the PoE network
Connection to the IP network
The connection is carried out by a 10/100 Mbit RJ45 Ethernet link.
Connection of the relay output
The connection is carried out via a 3-point terminal block providing a "make-and-break contact" interface (TRC).
If you use one of these relay outputs to control an AC or DC door release, wire a non-polarised 58 V diode in
parallel on the dry contact between C and T or between C and R according to the intended use (diode included).
Input connection
An on-off input allows the connection of a dry contact (do not supply power). In order to be activated, the input
must be earthed.
The contact can be up to 1 km away.
the door entry station by using the terminal supplied (mounted on microphone mount).
Debug

AUDIOVIDEOIPWASHABLEMASTERSTATION
Technical data sheet no. EN-604-0008G
www.castel.fr
Page 3 / 8
INSTALLATION
Flush mounting:
- Make a recess in the support with the following minimum dimensions: height 268 mm, width 112 mm and depth
48 mm.
- Position and attach the embeddable base in the recess, pressing the embedding abutments against the support
in which the recess is made.
- Position and clip the plate onto the base.
40= =
60= =
130= =
183
273,1
26= =
16,25
280
44,9
47 4
265,1
110= =
Butée d’encastrement
IMPORTANT WARNING: Use a flat screwdriver to remove the plate, inserting the tip in the slot provided for this
purpose at the bottom of the plate. Next, rotate the screwdriver and pull manually in order to release the plate from its
suppor

AUDIOVIDEOIPWASHABLEMASTERSTATION
Technical data sheet no. EN-604-0008G
www.castel.fr
Page 4 / 8
USE
IP address of the station
Every station must have its own IP address in the network. This address can be provided by the network server
(DHCP addressing) or configured manually. The address can be configured from a PC using the web server of the
station
The station is delivered by default with a DHCP address. If no DHCP server is present, then the
station will take a fixed IP address of domain IP4All: 169.254.xx.xx. The IP address of station will be
found by the application CastelIPSearch or CASTELServeur. In the case where the discovery of the
IP address of the set is not possible, pressing the "reset" button of the station during operation
sets its IP address in 192.168.49.251..
Accessing the web server of the station
You can use any web browser, such as Firefox or Internet Explorer, to connect to the web server of the station. To do
so, open your internet browser on any PC connected to the network and enter: "https://" followed by the IP address of
the station ([https://ip_address_of_the_station]). You will then be connected directly to the web page for the station.
Now you simply need to enter your username (default: admin) and password (default: admin) to access the functions
of the web server.
The web server provides information on the station and allows you to configure
it.
In order to access all the functions, go to View / Full view.
On-line help, which can be accessed from any menu, provides information on
the various functions of the web server.

AUDIOVIDEOIPWASHABLEMASTERSTATION
Technical data sheet no. EN-604-0008G
www.castel.fr
Page 5 / 8
FUNCTIONS
The washable master station is designed to dialogue, via the IP network, with other XELLIP stations, softphones, SIP phones or
any other elements that are compatible with the SIP standard.
General functions of the washable master station
Configuring a network connection
Setting up a SIP account
Managing audio communication
↘Setting the level of priority of the station
↘Setting a call and communication time-out
↘Automatic pick-up with and without delay
↘Enabling secret mode for automatic pick-up
Configure the viewer to customize the greeting or sleep timer
Configure the keyboard to indicate the delay before the automatic lock
Functions of the audio interface
Setting the speaker volume and the microphone volume
Setting the voice transmission mode (Full Duplex / Half Duplex)
Setting a noise-reduction level
Configuring the RTP port number
Validating / invalidating audio codecs
Set up ring tones and tones
Configure DTMF commands to control for example the local relay
Configure noise detection
Switch to simplex via a DTMF command:
↘'*' to switch to simplex listening
↘'#' to switch to speech simplex
↘'0' returns to standard operation
Programmable button functions
All the buttons are programmable and can be used for:
Making a call to 1 to 10 stations, simultaneously or with a time-delay
Controlling the local relay, the relay of the station making or receiving the communication
Sending a DTMF code
Activating forwarding to a station
Activating a call transfer
Activating "do not disturb" mode
Functions of the on-off input interface
Configuring the STATUS or COUNTER input
Configuring the active status of the input (contact open or closed)
Setting a timer for acknowledging a status change (anti-bounce function)
Configuring the counter threshold
Inhibiting the input
Functions of the output interface
The relay output interface can be programmed for:
Configuring the type of relay output: monostable, bistable or flashing
Configuring the type of NO/NC contact
Controlling the Start/Stop output
Controlling the Forcing Open/Closed output
Configuring the time parameters of the output
Functions of logical inputs (or flags)
Logic inputs allow two features in particular:
create a logical state from which it will be possible to condition actions in relationships.
create a counter that will be updated according to events and depending on the value of this counter to trigger
one or more actions.

AUDIOVIDEOIPWASHABLEMASTERSTATION
Technical data sheet no. EN-604-0008G
www.castel.fr
Page 6 / 8
Configuring relations
The Web server is where automatic controls, also called relations, are configured
There are two types of relations:
Time: used to trigger actions at identified time slots. There are three levels of priority for a time relation (high,
medium and low).
Logical:
↘Logical condition: used to trigger actions at certain status conditions (active, inactive, etc.). A logical
relation can integrate several conditions by operators such as AND, OR, NOT, XOR. Likewise, a logical
relation can trigger several actions.
↘Digital condition (Counting): used to perform actions by comparing the value of a counter with different
thresholds. It is also possible to add or subtract counter values and compare the result obtained.
Configuration of web server users (software users)
The Web server for the station can grant, modify or remove rights for users by specifying their login, password and
operating language.
Function for voice-transmission users of the station
In the user tab, you can create, edit or delete the voice-transmission users to whom you assign a profile. Then, a user
can log into the station using his/her username and password and activate his/her profile on the station.
Profile configuration
Station operating profiles can be created, modified or deleted. Each profile specifies a station priority, a configuration
of function buttons and access rights to the station.
The station can operate with a unique profile or with different profiles according to time slots.
Directory configuration
Station directory inputs can be created, modified or deleted.
It is possible to create inputs for simple calls or multiple calls
Local access configuration
It is possible to configure a simplified access control on the station:
↘Programming from 1 to 15,000 access codes of 1 to 20 figures.
↘Programming action or actions associated with access authorisation and denial by logical relations.
↘Recognition of time slots
SNMP administration management
The station features an SNMP agent (Simple Network Management Protocol) that can respond to SNMP queries and
send notifications (TRAPS) to an SNMP manager.
From web pages, it is possible to:
Configure different communities (read/write)
Configure system data (sysContact and sysLocation)
Configure notifications (recipient, community, etc.)
Download MIB Castel
It supports the SNMPv1 and SNMPv2c versions.
Self-test function
The station has several tests to validate its operation:
HP/MIC self-test: can remotely test the right operation of the speaker and microphone. From the ‘advanced
parameters’ page, the levels of this test can be adapted according to the installation environment. This test can
be activated from the web server or by an SNMP command. The result of the test can be viewed from the web
server history and by an SNMP notification.
Mechanical button self-test: the detection of a locked mechanical button (contact made for more than 20 s) is
signalled by an SNMP notification and an event is signalled in the web server history.
Backup and recovery of system parameters
A full backup or recovery of the station parameters can be made (configuration, profiles, relations, directory, etc.
The door entry station can be reset to factory settings by pressing the reset button for 10 seconds when the station is
started up.

AUDIOVIDEOIPWASHABLEMASTERSTATION
Technical data sheet no. EN-604-0008G
www.castel.fr
Page 7 / 8
Station update
For the update, you will be provided with a file containing the new software version, if necessary.
You must then download this file via the Web Page. The entry station will restart so as to apply the update. The
update does not modify the user parameters in any way.
Backup on power outage
When a power outage occurs, the station can back up the following information:
counter values
history
backed up events (these events are defined from CastelServer)
The interface statuses
History function
The history displays station events. They are listed by showing the date and time of the relevant event, a description
and additional information.

AUDIOVIDEOIPWASHABLEMASTERSTATION
Environmental protection:
Dispose of this product in compliance with the environmental protection regulations.
Technical data sheet no. EN-604-0402A
www.castel.fr
Page 8 / 8
CASTEL: ZAC de La Ronde –10 route du Bois de La Casse –49680 NEUILLE –France
Tel.: [phone] - Fax: [phone]
Non-contractual photos and document. Concerned with achieving continuous improvement, CASTEL reserves the possibility of making any modification
considered to be necessary.
TECHNICAL CHARACTERISTICS
Compliance with European standards
Safety according to EN 60950
EMC emissions according to EN 55022 class B
EMC immunity according to EN 55024
Mechanical characteristics
Protection rating IP54 according to EN 60529.
Polyester front panel.
Weight: 1.5 kg
Raised or flush mounting (optional).
Dimensions:
↘Front panel: H 280 mm x W 130 mm
↘Embeddable base: H 265 mm x W 110
mm x D 47 mm
↘Strap (optional): H 282.5 mm x W 132.5
mm x D 65 mm
Handset features
White ABS base with satin finish for wall
mounting
Numerous fixing points allowing an adjustment of
the verticality.
White satin-finish ABS handset with built-in
speaker and boom and microphone. It is
connected to the base by a spiral cord
connectable RJ jack.
Dimensions: H 236 x W 101 x D 65mm
General electric characteristics
Protection against electric shocks, class 3
according to EN 60950
Storage temperature: -20 ºC to +70°C.
Operating temperature: 0 to +50°C
Input voltage: 15VDC (15V to 30V)
Consumption: 15V/150 mA in standby and
15V/200 mA during communication
Buttons
Acquisition speed 5 Hz (200 ms)
Inputs
1 protected and filtered digital inputs
Acquisition speed 5 Hz (200 ms)
Outputs
1 potential-free relay outputs
Relay cutoff power 42.4 Vac/60 V dc/5 A/150 VA
The maximum frequency is 5 Hz (minimum
switching time: 200 ms)
Display:
Backlit 128x64 pixel graphic display.
White text on blue background
Audio codecs
G711 Ulaw/Alaw
GSM
G722
DTMF
RFC-2833
SIP INFO
Ethernet 10/100/1000 Mbps network
Fixed IP or DHCP
PoE class0 conformity with standard IEEE
802.3af
Option Wi-Fi wireless network according to IEEE
802.11b/g standard
Security of Ethernet connections via protocol
802.1X
SNMP V1 and V2c