Norac U5 User manual

PULSE Display Kit – Pull Type
Installation Manual
PULSE-PT01

Printed in Canada
Copyright 2010 by NORAC Systems International Inc.
Reorder P/N: PULSE-PT01-INST Rev B (PULSE Display Kit – Pull Type)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.

1
Contents
1INTRODUCTION..................................................................................................... 2
1.1List of Parts..........................................................................................................................................................................2
1.2Optional RAM Mount Ordering Information ...............................................................................................................2
2TECHNICAL SPECIFICATIONS ............................................................................ 3
3INSTALLATION........................................................................................................ 4
4CABLE DRAWINGS ................................................................................................. 6
4.1ITEM C01: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M ...........................................................................6
4.2ITEM C02: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M ...........................................................................6

2
1Introduction
The PULSE™ Display Kit Manual is intended to be used in conjunction with the UC5™ Spray
Height Control Installation Manual. This manual provides instructions to interface the UC5
Control Module to the PULSE Display. For installation of the rest of the UC5 Spray Height
Control System please refer to the sprayer specific manual provided with the kit.
Your input can help make us better! If you find issues or have suggestions regarding the parts
list or the installation procedure, please don’t hesitate to contact us.
1.1 List of Parts
Item Part Number Name Quantity
C01 43220-01 CABLE UC5 NETWORK 14 AWG 1M 2
C02 43220-03 CABLE UC5 NETWORK 14 AWG 3M 1
D01 43800 UC5 PULSE DISPLAY PANEL 1
E12 43764 UC5 NETWORK COUPLER 2-WAY 1
E20 43764T UC5 NETWORK COUPLER 2-WAY WITH TERMINATOR 2
M01 UC5-BC-MANUAL-ECHO_VT MANUAL UC5 OPERATORS - ECHO/VT 1
M04 PULSE-PT01-INST MANUAL UC5 PULSE DISPLAY KIT - PULL TYPE 1
If this kit is being installed with an existing system with control module serial
number lower than 3200, the following cable is required:
Item Part Number Name Quantity
C30 43250-17 CABLE UC5 POWER RETROFIT FOR ECHO SWITCH FUSED 1
1.2 Optional RAM Mount Ordering Information
This is an optional suction cup mount that may be useful when mounting the PULSE display.
This mount is not supplied with this kit, but can be ordered as per the following information:
To order from NORAC: • Contact us at any of the numbers above.
• Part number - 106332
To order from RAM: • Go to www.ram-mount.com or visit your local RAM dealer.
• Part number - RAM-B-224-1U

3
2Technical Specifications
CAN ICES-3(A)/NMB-3(A)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at their
own expense.
This Class A digital apparatus complies with Canadian ICES-003.
Pursuant to EMC Directive – Article 9, this product is not intended for residential use.
Table 1: System Specifications
Supply Voltage (rated) 12VDC
Supply Current (rated) 10
A
Hydraulic Pressure (maximum) 3300 psi
Baud Rate 250 kbps
Clock Frequency (maximum) 96 MHz
Solenoid Valve PWM Frequency 300 Hz
Ultrasonic Sensor Transmit Frequency 50 kHz
Operating Temperature Range 0°C to 80°C

4
3Installation
Ensure the PULSE power switch is OFF for the remainder of the installation
(Bottom of switch pressed IN).
1. Install the PULSE™ display in the cab of the sprayer where it will be clearly visible and
within easy reach of the operator.
2. RAM manufactures a suction cup mount that works well for installing the PULSE display.
The suction cup mount is not supplied with this kit, but is available from NORAC or RAM.
See Section 1.2 for ordering information.
3. Connect the cable from the PULSE display (D01) to one of the 2-way couplers with
terminator (E20) and connect one of the network cables (C01) to the other side of the
coupler.
4. Connect the remaining coupler with terminator (E20) to the free end of the network cable
(C01).
NOTE: Items E20 (2-way coupler with terminator) are white in color.
5. Connect the remaining cable C01 to the other side of the coupler with terminator (E20).
6. Connect the free end of the second network cable (C01) to the Display Bus connector on
the control module (E01). This is the end of the control module that only has one Deutsch
connector.
7. Disconnect the existing cable C01 from the control module. Connect cable C02 to the
control module.
8. Route cable C02 to the hitch and connect the 2-way coupler (E12) between cable C02 and
the existing cable C01. This will serve as the hitch disconnect.
NOTE: Only parts shown in black are included with this kit. Parts shown in blue
are included with the UC5 Spray Height Control System.

5
Figure 1: PULSE Pull Type Display Kit Parts

6
4Cable Drawings
4.1 ITEM C01: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M
4.2 ITEM C02: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M

Canada
NORAC Systems International Inc.
Phone: [phone]
Toll Free: 1 800 667 3921
Shipping Address:
3702 Kinnear Place
Saskatoon, SK
S7P 0A6
United States
NORAC, Inc.
Phone: [phone]
Toll Free: 1 866 306 6722
Shipping Address:
6667 West Old Shakopee Road, Suite 111
Bloomington, MN
55438
Europe
NORAC Europe
Phone: (+33) (0)4 26 47 04 42
Shipping Address:
Rue de l’hermitage
01090 GUEREINS
France
www.norac.ca