Catler CG 510 User manual

CG 510
Instructions for use
COFFEE GRINDER
COFFEE GRINDER

COFFEE GRINDER

2TABLE OF CONTENTS
TABLE OF CONTENTS
4 Catler recommends safety rst
7 Know your CG 510 COFFEE grinder
9 Operating your CG 510 coee grinder
12 Care and cleaning

3
CATLER RECOMMENDS SAFETY FIRST 3 CONGRATULATIONS
Congratulations
for purchasing your new coee grinder CG 510.

4CATLER RECOMMENDS SAFETY FIRST
CATLER RECOMMENDS SAFETY FIRST
• This appliance is not to be used by children.
Keep this appliance and its power cord out of
children.
• The appliances may be used by persons
with physical or mental impairments or by
inexperienced persons only if they are properly
supervised or have been informed about how
to use of the product in a safe manner and
understand the potential dangers.
• Cleaning and maintenance performed by the
user must not be performed by children.
• Children must not play with the appliance.
• If the power cord is damaged, ask the
authorised service for a replacement in order
to prevent hazards. It is forbidden to use the
appliance if it has a damaged power cord.
• WARNING: Misuse may cause injury.
• Please pay increased attention to handling the
burrs not to cause injury.
• Wipe the coee bean hopper with a soft
sponge lightly moistened in warm water and
wipe dry. Wash the coee container in warm
water with a small amount of washing-up
liquid. Rinse and wipe dry.

5
CATLER RECOMMENDS SAFETY FIRST
• Always disconnect the appliance from the
power socket if you are leaving it unattended
and before assembly, disassembly, or cleaning.
• Before exchanging the accessories or accessible
movable parts, please turn the appliance o
and disconnect it from the power supply.
• This appliance is designed for household use only. This appliance is not designed for
commercial use. Do not use this appliance in moving vehicles or on boats, outdoors, or for
any purpose other than it’s intended. Otherwise, there is a risk of personal injury.
• The appliance is not intended for use in premises such as:
– sta kitchens in stores, oces and other workplaces;
– hotel or motel rooms and other living areas;
– agricultural farms;
– bed and breakfast establishments.
• Do not submerge the appliance, power cord, or plug in water or any other liquid.
• Make sure that the mains cord and plug do not come into contact with water or other
liquid.
• Use the appliances according to the instructions in this user's manual. Otherwise, injury,
damage to the appliance or dangerous situation might occur.
• Do not use this appliance with a programmable switch, timer switch or any other device
that automatically switches the appliance on.
• This appliance has been designed ONLY to grind roasted coee beans. Never use the
appliance for purposes other than those for which it was designed.
• This appliance is NOT designed to grind pre-ground coee. Under no circumstances
should the appliance be used to grind gluey food or extremely hard food, to make dough
and grind fruit, seeds or herbs for example to produce curry pasta or nut butter.
• Do the put metallic objects or similar items that might damage or adversely inuence the
appliance operation in the coee bean hopper.
• Before connecting the appliance to a power socket, check that the nominal voltage on the
appliance's rating label matches the electrical voltage in the socket.
• Connect the appliance only to a properly grounded socket. For safety reasons, we don’t
recommend using adaptor plugs or extension cords.
• Do not place the appliance on windowsills, sink drip tray or on unstable surfaces. Always
place the appliance on a stable, at, and dry surface.
• Do not place the appliance on electric or gas cooker or in the vicinity of naked ame.
• Never use the appliance in close vicinity of a bath, shower, or swimming pool.
• Only use the appliance with the original supplied accessories.
• Always turn the appliance o and disconnect from the power socket if it’s to be unused or
left unattended, before disassembling or assembling, before lling the hopper or before
moving or cleaning. Allow the appliance to fully cool down before cleaning or moving.
• Keep the appliance and its accessories in clean condition. Perform the cleaning and

6CATLER RECOMMENDS SAFETY FIRST
maintenance in accordance with the instructions in chapter Cleaning and maintenance.
Never wash the appliance under running water or submerge it in water or another liquid.
• Before turning the appliance on, attach the coee bean hopper lid properly on the
hopper.
• Do not turn the appliance on until the coee bean hopper and the lid is properly secured
in place.
• Do not use the appliance if the coee bean hopper is not properly attached. Be careful
during operation and do no insert ngers, hands, hair, clothing, or kitchen utensils in the
vicinity of the coee bean hopper.
• Do not use the appliance for longer than 2 minutes, otherwise it might overheat. If such
situation occurs, please turn the appliance o and disconnect it from the power supply.
Allow the appliance to cool down for 30 minutes, the try to turn it on again.
• Before connecting this appliance to a power socket, make sure the voltage stated on the
product's rating label corresponds to the voltage in your power socket.
• Do not disconnect the appliance from the power socket by pulling the power cord. This
could damage the power cord or the power socket. Disconnect the cord from the power
socket by gently pulling the plug of the power cord.
IMPORTANT SAFETY INSTRUCTIONS FOR USING ELECTRICAL EQUIPMENT
• Fully unwind the power cord before use.
• Do not leave the power cord hanging over the edge of a table or countertop or allow it
to touch a hot surface or to become tangled up. Do not put heavy objects on the power
cord.
• For safety reasons, we recommend connecting the appliance in an independent electrical
circuit separated from other appliances. Do not use adapter plugs or extension cords to
connect the appliance to a power outlet.
• To prevent potential electric shock, do not submerge this appliance, its base or power
cord in water or any other liquid.
• We recommend that you inspect the appliance regularly. Do not use the appliance if it is
damaged in any way or if the power cord or plug are defective. All repairs or adjustments
must be performed at the nearest Catler authorised service centre.
• Any maintenance other than standard cleaning must be performed at authorised Catler
service centre.
• We recommend installing a residual current device (standard safety switches in your
power outlet) to provide a higher level of protection when using the appliance. We
recommend installing a residual current device (with a nominal residual operating current
of no more than 30mA) in the electric circuit in which your appliance is to be connected.
For further expert advice, please contact your electrician.
The user’s manual is also available at www.catler.eu.

7
KNOW YOUR CG 510 OFFEE GRINDER
KNOW YOUR CG 510 COFFEE GRINDER
9
1
2
3
4
5
7
6
8
13
14 15 16 17
10
11
12

8KNOW YOUR CG 510 OFFEE GRINDER
1. Coee bean hopper lid
2. Coee bean hopper
The coee bean hopper with a capacity of around 250g is equipped with a special
lockable system to facilitate handling the hopper and transferring unused coee beans
into the air-tight container.
3. Upper conical burr
4. Coee bean hopper release button
5. Grind size control knob
The control knob’s rotary mechanism allows you to select the correct ground level from
31 presets. You can easily and comfortably grind your coee for various uses from French
press to espresso machines.
6. Stainless grinder housing
The stainless grinder housing with a built-in motor forms a stable and powerful grinder
base.
7. Control panel
8. Ground coee release chambre
The release chamber is designed to allow you to grind coee directly into the handle as
well as the jar.
9. Portalter holder
The coee grinder is supplied with two holders of dierent sizes. Thus, you can grind your
coee directly into the holder for both professional and household coee machine.
10. Cleaning brush
11. Ground coee jar lid
12. Ground coee jar
13. Display
14. SET button
15. + button
16. – button
17. button

9
OPERATING YOUR CG 510 COFFEE GRINDER
OPERATING YOUR CG 510 COFFEE GRINDER
BEFORE FIRST USE
Remove all packaging from the appliance
and dispose of it in a proper manner. Before
a proper disposal, make sure you have
removed all accessories from the packaging.
Wash the ground coee jar and holders in
warm water with a small amount of washing-
up liquid. Rinse and wipe dry.
Wipe the coee grinder housing and coee
bean hopper with a soft sponge lightly
moistened in warm water and wipe dry.
COFFEE BEAN HOPPER  ATTACHING
AND REMOVING
1. Before attaching or removing the coee
bean hopper, always make sure the
power cord is disconnected from the
power socket.
2. Attaching the hopper: Align the
symbol on the hopper with symbol
above the coee bean hopper release
button (at the back of the grinder) and
turn the hopper till the symbol is
aligned with symbol.
3. Releasing and removing the hopper:
Press the coee bean hopper release
button to release the hopper. The hopper
releases and turns. Now, you can remove
the hopper from the grinder housing.
NOTE:
If it is not possible to attach the hopper
easily, remove any coee beans with the
cleaning brush. The grinder will not start
if the coee bean hopper is not attached
properly.
FILLING THE HOPPER
Ensure the hopper is correctly attached.
Remove the hopper lid and ll it with fresh
coee beans.
Attach the lid. Always ensure the lid is
securely attached before turning the grinder
on.
NOTE:
We recommend lling the hopper up to
the maximum level line. This will exert
a constant pressure on the burr stones
which is important for correct grinding.
WARNING!
PLEASE
PUT ONLY FRESH
ROASTED COFFEE
BEANS IN THE
COFFEE BEAN
HOPPER. NEVER
PUT GROUND
COFFEE, CRUSHED
COFFEE BEANS,
NUTS OR OTHER
FOODS IN THE
HOPPER.

10 OPERATING YOUR CG 510 COFFEE GRINDER
GRIND SIZE SETTING
The grind size is set by the control knob.
If the coee bean hopper is empty, set the
desired grind size while the grinder is
turned o.
If the coee bean hopper is full, set the
desired grind size once the grinder is in
operation.
Use the control knob to set the desired grind
size from 1 (the nest ground coee) to 31
(the coarsest ground coee). It’s important to
select the grind size according to the coee
making method. The line in the front of the
grinder shows the set grind size.
GRIND SIZE TABLE
Grind size
setting
Coee making method
1-2 Cezve
3-5 Espresso coee machines
6-10 Siphon coee machines
11-20 Drip-coee machines
17-25 Pour Over machines
26-31 French press
When selecting the grind size, please note
the following:
• The ner the ground coee is, the longer
the water runs through the strainer.
• The ner the ground coee is, the higher
is the risk of choking the grinder and the
release point. In such case, you can slightly
tap the hopper lid during grinding to
release the blocked ground coee.
• If you ground very ne coee for
a prolonged period of time, we
recommend that you clean the burr stones
after some time. The cleaning procedure is
described in the Care and Cleaning chapter
further in this manual.
GRINDING COFFEE
1. Put the appliance on a at, dry and clean
surface. Ensure it is correctly assembled,
the grind size is set and there are coee
beans in the hopper.
2. Place a jar or a cup under the ground
coee release chamber.
3. Insert the power cord plug to the power
socket.
4. There is a short been sound and the
display shows“01”and a cup symbol.
That means the grinder will grind one
portion of ground coee for one cup.
5. Use the +/- buttons to set the number of
portions of the ground coee from 1 to 10.
6. Press the button to start grinding. If
you need to stop grinding, press the
button again.
7. The grinder will automatically turn o
once the desired quantity of ground
coee has been milled.
NOTE:
The grinder remembers last setting once
you have turned it on again. That it not
applied when you disconnect the power
cord from the power socket.
AMENDMENT OF THE GRINDING TIME OF
ONE COFFEE PORTION
If you need to amend the grinding time of
one portion, it is necessary to set the number
of portions rst – see the previous part of the
manual.
1. After setting the number of portions,
press and hold the SET button until
“3.0”ashes on the display. That value
indicates the default grinding time of
one ground coee portion.
2. Use the +/- buttons to amend the coee
grinding time in the range from
3.0 to 5.0 seconds. Each press increases
or decreases the grinding time
by 0.1 second.

11
OPERATING YOUR CG 510 COFFEE GRINDER
3. Shortly press the SET button to save
the setting and press the to start
grinding.
GRINDING COFFEE INTO PORTAFILTER
1. Attach the portalter holder under the
ground coee release chamber. Push it
backwards until it clicks. The display will
automatically show a portalter symbol
(the grinder have recognised grinding
into portalter) and value “8.0”(the
default grinding time into portalter).
2. Use the +/- button to set the desired
grinding time from 5.0 to 20.0 seconds.
Each press increases or decreases the
grinding time by 0.1 second.
3. Insert a portalter to the holder.
4. Press the button to start grinding.
If you need to stop grinding, press the
button again.
NOTE:
If you do not insert the holder correctly,
it will not be possible to set the correct
grinding time.
STANDBY MODE
The grinding time will automatically turn o
and enter the standby mode after 3 minutes
of inactivity. Press any button to turn it on
again.
TIPS AND TRICKS
• Always select the grind size setting level
according to the coee making method
– see the grind size table in the previous
manual sections.
• If you prefer coee with weaker taste,
make the coee as recommended, then
pour some hot water in the cup.
• If the ground coee used is excessively
ne, the coee extraction may be very
slow. The resulting coee will be very
over-extracted and very bitter. On the
other hand, too coarsely ground coee
will speed up the extraction with the
resulting coee being under-extracted,
slack and without strong taste.
• The ground coee will lose its taste and
avour very quickly. We recommend that
you always use freshly ground coee
when making coee.
• Buy coee beans in smaller packages
with the roasting date stated.
• To prolong the coee bean freshness,
store the coee beans in an air-tight
container in a cool, dark and dry place.
The coee bean hopper is not suitable for
storing coee beans. Thus, it’s important
for you to transfer the coee beans from
the hopper to an appropriate container
for storage.
• Keep the grinder in a clean condition.
This will ensure that you always reach the
best results when making coee.

12 CARE AND CLEANING
CARE AND CLEANING
Before cleaning, unplug the mains cord from
the power outlet and allow the appliance to
cool down properly.
WARNING!
TO PREVENT
ELECTRIC SHOCK,
DO NOT SUBMERGE
THIS APPLIANCE,
PLUG OR POWER
CORD OR IN WATER
OR ANY OTHER
LIQUID. NO PART OF
YOUR APPLIANCE
IS SUITABLE FOR
DISHWASHER USE.
WARNING!
DO NOT
USE ABRASIVE
CLEANING AGENTS,
STEEL WOOLS, WIRE
SPONGES ETC.,
AS THESE MIGHT
DAMAGE THE
SURFACE.
CLEANING THE GRINDER HOUSING,
COFFEE BEAN HOPPER AND GROUND
COFFEE JAR
1. Remove the coee bean hopper from
the grinder base and transfer the unused
coee beans in an air-tight container.
2. Wipe the coee grinder housing and
coee bean hopper with a soft sponge
lightly moistened in warm water and
wipe dry.
3. Wash the ground coee jar, lid and
holders in warm water with a small
amount of washing-up liquid. Rinse and
wipe dry.
CLEANING THE BURR STONES
Depending on the grinder frequency of
use, the burr stones should be cleaned on
regular basis. If you use the grinder daily,
it’s necessary to clean the burr stones about
every three weeks to ensure correct grinder
operation. Regular maintenance will extend
the lifetime of the burr stones, therefore the
lifetime of the entire grinder.
1. Release and remove the coee bean
hopper. Transfer the coee beans in an
air-tight container.
2. Attach the empty hopper back to grinder
and run the grinder empty to remove
the rest of the coee beans from the burr
stones. Then release and remove the
coee bean hopper again.
3. Take the upper conical burr by a handle
and turn it anti-clockwise to release it
and then remove it from the grinding
chamber.
4. Use the cleaning brush to remove the
ground coee residues from the upper
conical burr.
5. Use the cleaning brush to clean the
lower conical burr, grinding chamber and
ground coee release outlet as well.
6. Place the upper conical burr into the
grinding chamber so that the protrusions
in the grinding chamber were aligned
with the openings on the upper conical

13
CARE AND CLEANING
burr. Turn the upper conical burr
clockwise until you feel resistance.
7. Attach the coee bean hopper.
THERMAL FUSE
The grinder is equipped with a thermal
fuse that is activated when it should be
overheated. If such situation occurs, the
grinder will automatically pause its operation
and turn o. Disconnect the power cord from
the power outlet and allow it to cool down
for about 30 minutes. Then, you can use it
again.
STORAGE
If the grinder is to be left unused, clean it
according to the above instructions. Store
the grinder in a well-ventilated dry place out
of reach of children and animals.
ERROR MESSAGES
Error
code Description Solution
E1
The coee bean hopper is not
attached, or it is not attached cor-
rectly.
Attach the coee bean hopper according
to the instructions in this manual.
E2
The total grinding time is 100 sec-
onds. The grinder will automatically
turn o not to get overheated and
damaged.
Remove the power cord plug from the
power outlet and allow the grinder to cool
down for about 30 minutes. Then, you can
use it again
The motor is overheated.
Note:
If the problem persists, stop using the grinder and contact an authorised service centre.

14
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
MATERIALS
Dispose of packaging material at apublic waste disposal site.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES
The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not
be treated as household waste. Please, dispose of this product at your applicable collection point for the
recycling of electrical & electronic equipment waste. Alternatively in some states of the European Union or
other European states you may return your products to your local retailer when buying an equivalent new
product. The correct disposal of this product will help save valuable natural resources and help in preventing
the potential negative impact on the environment and human health, which could be caused as aresult of
improper liquidation of waste. Please ask your local authorities or the nearest waste collection centre for
further details. The improper disposal of this type of waste may fall subject to national regulations for  nes.
For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the necessary information from your seller
or supplier.
Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information about the correct disposal method
from local government departments or from your seller.
The product applies all regulations of EU.
Changes to the text, design and technical specications may occur without prior notice and we reserve the right to make
these changes.
The original version is in the Czech language.
Address of the manufacturer: FAST ČR, a.s., USanitasu 1621, Říčany CZ-251 01

16
WWW.CATLER.EU