CATSKILL 1529 User manual

CRAFTSMEN, INC.
Assembly Instructions
Model 1529
Cuisine Cart Deluxe
GENERAL:
1. You have purchased model 1529. Overall dimensions of an assembled unit is 21” x 15 1/4” x 34”
2. Should you need assistance or need to replace a damaged or missing part, DO NOT RETURN THE
UNIT TO THE STORE where you purchased it, simply give us a call at 607-652-7321 from 7:30 - 4:00 PM
Eastern time and we’ll send you the prepaid part via UPS usually that same day! Please have model
number and part description ready when you call.
3. Read the assembly instructions and the enclosed brochure before beginning assembly.
Assembly is very easy if you read and follow the instructions step by step.
4. Tools required: Phillips screwdrivers, medium and small; medium flat blade screwdriver and hammer.

Side Panel (2)
TOP TOP
Back Panel (1)
Drawer Dowel (1)
Drawer Front (1)
Drawer Back (1)
Middle Shelf (1)
Left Door (1) Right Door (1)
Drawer Side Left (1)
Drawer Side Right (1)
Table Top Stick (2)
Door Spacer (1)
Bottom Brace (1)
Cabinet Top(1)
CABINET PARTS
Middle Brace (1)
Drawer Bottom (1)
P1 P2
T1
T2
B1
B2
D1
D2
D3
D4
D5
D6
D7
D8 D9
MS
Bottom Shelf (1)
BS
Middle Shelf has edge banding

1 3/4” Phillips Flat Head Machine Screw (8)
Cam Posts (2)
1 1/4” Phillips Flat Head #8 Screw (12)
1 1/4” Truss Head Machine Screw (2)
3/4” Long 3/16” DIA. Steel Pin (4)
1” Long 3/16” DIA. Steel Pin (8)
1 1/2” Long 3/16” DIA. Steel Pin (4)
Caster Socket (4)
Cam (2)
5/8 Wooden Disk (8)
Non Locking Wheel Caster (2)
Locking Wheel Caster (2)
Magnet (1)
3/16” Flat Washer (2)
10-24 Hex Nut (8)
CABINET HARDWARE
5/8” Phillips Flat Head #8 Screw (3)
5/8” Pan Head Screw (2)
included in
magnet pack
1/2” Phillips Flat Head #4 Screw (1)
included in
magnet pack
Magnet Plate (1)
included in
magnet pack
1/2” Truss Head Machine Screw (2)
Cup Handle (1)
Door Knob (2)

STEP 1 1 1/4” #8 Screw
STEP 2
1” Steel Pin
1 3/4” Machine Screw
Nut
T2
T2
Repeat to other Side Panel
P2
P1
P1
P1
P1

1 1/4” Screw
STEP 3
P2
P1 P1
T1

STEP 4
A. Attach the drawer back to the drawer sides with
four 1 1/4” #8 screws. Make sure parts are aligned
as in illustration 4A.
B. Insert drawer bottom into the slots in the drawer
sides, best side to inside of drawer. Slide down
until seated in the slot in the drawer back.
See illustration4B.
C. Screw the cam posts into the two outside holes
on the inside face of the drawer front until seated.
Only 3/8” of this post goes into the wood, leaving
the 4 guide rings/head exposed. See illustration 4C.
D. Insert the posts into holes in the drawer sides
until seated against the front end of the drawer
sides. Insert cams so that slot in the cam fits over
the post and turn with Phillips screwdriver until
seated. Don’t over-torque! See illustration 4D.
E. Attach drawer handle with the two 1/2” handle
screws ( no illustration ).
ILLUSTRATION 4A
Below line in wood
Cam Posts (2)
ILLUSTRATION 4B
ILLUSTRATION 4D
1 1/4” Phillips Flat Head #8 Screw (14)
4 used
in this step
Cam (2)
2 used
in this step
1/2” Truss Head Machine Screw (6)
2 used
in this step
ILLUSTRATION 4C
D1
D2
D3 D4
D2
D3 D4
D5
D2
D5
D1
D4 D3

STEP 5
1 1/2” Pin 1/2” #4 Screw
1 1/4” Machine Screw
5/8” #8 Screw
Magnet Plate
STEP 6
Door assembly
D1
D6
D9 D8
Door
Knob
D7
Place drawer in position

STEP 6
1 3/4” Machine Screw
Nut
3/4” Pin
STEP 7
Install 3/4” pins in brace ends
B1
B2
B1

Washer
STEP 7
B1
B2
D8
D9
1 3/4” Machine Screw

STEP 8
A. Stick magnet to magnet plate on right door.
B. With left door open, close the right door. The magnet should be positioned over the wooden block
on the bottom of the top front brace. Hold the magnet in place with your thumb, and open the right
door. The magnet will be in the correct position on the block.
C. Secure magnet with the two round head screws in the magnet packet. Center screws in the slots in
the magnet . This will allow adjustment later, if needed.
NOTE: No pilot holes in block, as softwood!
Magnet (1)
5/8” Pan Head Screw (2)
2 Used
in this step
B1
D8
D9
B2

STEP 9
BS
MS

STEP 10

5/8” Wooden disk
STEP 11
Tap in the 5/8” wooden disks. If you are afraid of marring the disks, you can cover them with a
piece of paper.

Catskill Craftsmen, Inc.
15 West End Ave.
Stamford, NY 12167-1296
CRAFTSMEN, INC.
BUTCHER BLOCK OIL COUPON
CRAFTSMEN, INC.
NAME _____________________________________
ADDRESS __________________________________
__________________________________________
CITY ______________________________________
STATE _________________________ ZIP _______
Please make checks payable to: Catskill Craftsmen Inc.
15 West End Ave. Stamford, NY 12167-1296
Please send me _____# of bottle(s) of the
Catskill Craftsmen Butcher Block Oil at $6.95.
My Check or Money Order is enclosed for a
total of $______________.
Item Code: 1529
013013
For continued beauty and long life of
your Catskill Craftsmen cart, we
recommend Catskill Craftsmen’s Butcher
Block Oil.
If you would like to purchase Butcher
Block Oil directly from Catskill
Craftsmen’s factory, we offer a reduced
price. For one eight ounce (8 fl. oz.)
bottle, which is sufficient for two
applications, simply send $6.95 along
with the completed coupon to the
address below or visit us online at
www.catskillcraftsmen.com for other
ordering options.