CBM CMP-10 User manual

CITIZEN CMP-10 1

2 CITIZEN CMP-10

Manufacturer’s Name : Japan CBM Corporation

Manufacturer’s Address: CBM Bldg., 5-68-10, Nakano, Nakano-ku

Tokyo, 164-0001, Japan

Declardtion on the Product

Product Name LineThermalPrinter

Model Number(s) CMP-10

(S.No.9880001 - )

Conforms with the following standards:

EN60950 A4

EN55022 1994 Class A

EN61000-3-2 1995

EN50082-1 1992

IEC801-2 1991 4KV CD, 8KV AD

IEC801-3 19843V/m,26MHz-1000MHz

AM1KHz80%

IEC801-4 1988+ 0.5KV Signal line

+ 1KV AC mains

Supplementaryinformation

“The product complies with the requirements of the low Voltage

Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336EEC,

92/31/EEC, 93/68EEC”.

Tokyo, Japan Signature:

July1988 Mikio Moriya

GeneralManager

R & D Department

DECLARATION OF CONFORMITY

WARNING!

This is a Class A product. In a domestic environment it may cause radio

interference in which case the user may be required to take adequate measures.

CITIZEN CMP-10 3

READ THESE INSTRUCTIONS CAREFULLY!

·Follow all warnings and instructions marked on the product.

·Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

·Do not place this product on an unstable cart, stand or table. The product

may fall, causing serious damage to the product.

·The slots and openings on the back or bottom of the case are provided for

ventilation. To ensure reliable operation of the product and to protect it

from overheating, do not block or cover these openings. They should never

be blocked by placing the product on beds, sofas, rugs or other similar

surfaces. This product should never be placed near to or over a radiator or

heater. It should not be placed in an built-in installation unless proper venti-

lation is provided.

·This product should be operated from the type of power source indicated

on the marking label.

·Never push objects of any kind into the device through cabinet slots as

they may touch dangerous voltage points or other vital parts that could lead

to excessive risk of fire or electric shock. Never spill liquid of any kind on

the product.

·Do not attempt to service this product yourself.

IMPORTANT! This equipment generates, uses, and emits radio frequency

energyandifnot installedand usedin accordancewith theinstruction manual,

may cause interference to radio communications. It has been tested and

found to comply with the limits for a Class A computing devices pursuant

to Sub-part J of Part 15 off FCC Rules, designed to provide reasonable

protection against such interference when operated in commercial environ-

ments. Operating this equipment in a residential area is likely to cause inter-

ference, in which case the user - at his own expense - will be required to take

whatever measures may be necessary to correct the interference.

CAUTION: Use shielded cable for this equipment.

4 CITIZEN CMP-10

i

FOLLOW INSTRUCTIONS STRICTLY

MAY CAUSE DAMAGE TO THE UNIT

· Do not subject the printer to strong impacts or shocks, such as kicking, stamping,

hitting, dropping, and the like.

· Install the printer in well-ventilated places. Do not use it in such a way as to cause

the closure of its ventilation.

· Do not install the device in chemical laboratories, where reactions are expected to

take place or in locations where salts or gases contaminate the air.

· Do not connect/disconnect the power cord or the data cable, while holding the cable

itself!

· Do not pull, install, use, or carry the equipment in a way as to apply excessive force

on the cables.

· Do not drop or insert any external objects, such as clips or pins, into the equipment.

· Do not spill liquids or spray any chemical-containing liquid over the equipment. If

any liquid is spilled on it, turn off the power, disconnect the power cable and power

cord from the mains socket and contact our local dealer.

· Do not disassemble or remodel the equipment. Treatment of this kind may cause fire

or dangerous electric shocks.

· Use the printer only with the specified commercial power supply and AC adapter.

· If you drop or break the AC adapter, or if water or other liquid substances get

inside it, unplug it immediately from the mains socket and contact our dealer.

· Do not damage, break, bend, pull by force or twist the AC adapter cord. Do not put

heavy objects on it or apply excessive heat. The AC adapter may brake and

cause fire, electric shocks, etc. If the AC adapter cord is damaged, contact our

local dealer.

· Do not connect/disconnect the AC adapter with wet hands.

· Do not overload a single electrical outlet, using a table tap or a current tap socket.

· The packing plastic bag of the printer must be kept away from children -

DANGER OF SUFFOCATION!

CITIZEN CMP-10 5

· Do not use or store the printer in locations exposed to fire, moisture, direct sunshine

or near heaters or thermal devices where the prescribed operating temperature and

humidity are not met, or in a places exposed to oil leaks, iron powder, or dust. The

device may brake, emit smoke, or catch fire.

· Install the printer on a flat, stable desks or tables free from vibrations.

· Do not use any sharp-pointed objects, such as a pens, to touch the operation panel

of the printer.

· Do not use the device near radio or TV receivers. Do not share the power from a

common socket together with radio or TV receivers because this may cause recep-

tion problems.

· Use the printer only with the specified power supply, voltage and frequency.

· Confirm that the mains socket, used for the connection, has sufficient capacity.

· Avoid connecting the power cable to a mains socket shared by other devices or

extending the wiring too fa - the cable may catch fire. Do not step on or apply

excessive force (pull) to the cable.

· Never connect the grounding cable (frame ground) to a gas pipe beacuse of the

danger of explosion. When connecting or disconnecting the grounding cable, be

sure to disconnect the power cable and the power plug from the mains socket.

· When connecting/disconnecting the cables, be sure to turn off the power first,

including the connected side, and then connect/disconnect them, holding the plug

and the connector.Pulling the cable itself cam seriously damage it.

·If a reverse-polarity connection is made, internal elements may be broken or a mating

device may be adversely affected.

· Use a shielding wire or twisted pair for a signal line, in order to minimize noise

effects. Do not route the cable too long or connect it to a noisy device. Connection

to noisy devices can cause erroneous printing due to corrupt data.

· Use the printer in locations where the mains socket is close at hand so that you can

easily disconnect the power plug from it and shut off the power.

· When the printer will be kept in storage for longer periods of time, or during transpor

tation, unplug all cables from it and remove the paper roll.

i

PRECAUTIONS DURING INSTALLATION

6 CITIZEN CMP-10

DAILY MAINTENANCE

PROCEDURES!

CAUTION!

During printing the head and motor are very hot. Be careful not to touch

them before they cool off. Do not touch the heating surface of the with

bare hands or metal objects.

CLEANING THE PRINTING HEAD

1. Referring to “4.5 Removing Paper Jam,” dismount the plate roller unit.

2. Moisten slightly with alcohol, and clean the heating surface of the

printing head with it.

3. Reassemble the plate roller unit.

CAUTION!

When dismounting or reassembling the plate roller unit, be sure to raise

the printing head - otherwise, they may be damaged. Handle the de

tached plate roller unit with care or you may damage it.

i

CAUTION!

1. The use of non-specified paper may cause irregularity of printing den

sity. If this is the case, use the DIP switch to reset this parameter

2. Do not paste the paper to the core.

3. If the paper comes in contact with a chemical or oil, it may discolor or

fail to print.

4. Do not rub the paper surface with your finger nails or metal objects -it

may discolor.

i

· During maintenance operations be sure to switch the printer off and unplug it from

the socket.

· Use a dry soft cloth to wipe off stains and dust from the surfaces of the printer case.

For harder soiling, use a water moist cloth. Never use organic solvents, such as

alcohol, thinnesr,benzenes, ketone, or chemical dusters.

· If the printer is contaminated with paper powder, use a soft brush for cleaning. Be

careful not to damage the printing head.

CITIZEN CMP-10 7

Notes

.................................................................................................................................

8 CITIZEN CMP-10

CONTENTS:

DeclarationofConformity..........................................

Introduction...................................................................

Technicalparameters...................................................

Appearanceandcontrols............................................

Replacingthebatterypack.........................................

Functions.......................................................................

Replacingthepaperroll..............................................

Interfacespecifications...............................................

ListofCommands........................................................

3

9

12

14

17

18

19

21

22

CITIZEN CMP-10 9

Notes

.................................................................................................................................

10 CITIZEN CMP-10

Features:

1.Smalland lightweight.

2. High speed and low noise emission of the line thermal printing mechanism.

3. Long-life printing head and high reliability, owing to its simplicity.

4. Easy paper-loading, owing to the auto-loading function.

5.Built-inIrDA.

6. Built-in magstripe reader.

7. Accommodates two paper-roll diameters - 40 and 55 mm.

Unpacking

When unpacking the package, confirm the availability of:

·Printeruntit: 1

·Sample paper roll: 1roll

·AC adapter: 1 piece

·AC cord: 1 piece

·User’s manual: 1 copy

The CITIZEN CMP-10 is a compact, full featured line thermal printer, which can be

used in a large variety of job environments ranging from door-to-door sales through

small and mid-sized catering establishments, car-rentals, parking lots, field services to

on-board sales on land, sea and air. Its abundant built-in wireless technology features

allow the device to replace the traditional paper-based business processes and to realize

commercial transactions at the point of sale or service. Easily worn on the belt it is a

highly efficient device for printing plain text and graphic receipts on demand plus logos,

bar codes and other graphic elements.

CAUTION!

· Install the printer body on a flat and stable desk at a minimum risk of vibrations.

· Do not install the printer near a heater or in a place exposed to direct sunshine.

·Donotusetheprinterinhigh-temperature,high-humidity,orcontaminatedenvironments.

· Do not allow the formation of condensed moisture on the printer. If such condensa

tion appears do not switch the printer ON until it has become completely dry.

· Use only the accessory AC adapter. Do not use this adapter for other purposes.

INTRODUCTION

CBM CMP-10 User manual

Popular Printer manuals by other brands