CCR SR5 User manual
653RZHU6XSSO\&RQWUROOHU0DQXDO
&&5
3URFHVV3URGXFWV
7HUUHQFH0DWWKHZV&UHVFHQW.DQDWD2QWDULR.0& &DQDGD
7HO )D[
:DUUDQW\DQG5HSDLU3ROLF\
7+,6(;35(66:$55$17<683(5&('(6$1<$1'$//27+(5:$55$17,(6
(;35(66('25,03/,(' ,1&/8',1*,03/,(':$55$17<2)0(5&+$17$%,/,7<25
),71(66)253$57,&8/$5385326(
2%7$,1,1*6(59,&(81'(5:$55$17<
5(3$,5:$55$17<
7$%/(2)&217(176
FIGURES
Figure 3
Push
F
F
open collector outputs
Signal Input: 0-5 vdc
Input Resistance: > 1 Megohm
Input Bias Current: < 1 na
Displaype:
Max displaange: +/- 99,999 counts
A/D Resolution: +/- 19,999 counts
Linearty:
FS Accurcy:
FS Step Response: 500ms (typ)
Ov y: Flashing digits f
No Sensor Indication:
er Supply:
Operange:
Input P:
(solder pad jumper selectab
Pkg dimensions: 3.78W x 1.89H x 5.13D
,167$//$7,21$1':,5,1*
1. ner)
e sure
knesses up
to 0.25 inches (6.35mm).
2.
3. laps the
4.
Figure 1. SR5 Front Panel View
Figure 2. SR5 Model Rear Panel View
9$
Y$
/LQH
+]
0RGHO65
(Actual display text
may be different )
Figure 3. Transducer Wiring Diagram
Figure 4. I/O Wiring Diagram
** only used
when
connected to
MFC or
Pressure
Controller
5
1
***
***
*** 0 - 10 vdc optional
0RGH6ZLWFK6
Setpoint fw (StPt)
Set Pint High 1
Set Pw 1
Set Pint High 2
Set P (SPL2)
Hysteresis High
Hysteresis Lo
Cal
Decimal P (dP)
Exit
,QFUHPHQW6ZLWFK6
6:,7&+$1')81&7,21'(),1,7,216
66666
0RGHO65
A
)
B)
6WHSDQG0LQ0D[6ZLWFK6
=HURDQG([LW6ZLWFK6
QRW
&DO6ZLWFK6
C)
D)
E)
6HWSRLQW6W3W
1RWH,IVZLWFK6:G5HIHUHQFHGUDZLQJRQSJLV21WKHODVW6W3W
YDOXHZLOOEHUHFDOOHGDWSRZHUXSDOWKRXJKWKH6W3WGLVSOD\ZLOO
DOZD\VGLVSOD\WRDWSRZHUXSDQGPD\QRWFRUUHVSRQGWRWKH
DFWXDO6W3WYDOXH
,I6ZLWFK6:GLV2))WKH6W3WRXWSXWZLOOEH]HURDWSRZHUXS
6HW3RLQW+LJK63+
exceeds
6HW3RLQW/RZ63/
is
less
a)
b)
c)
6HW3RLQW+LJK63+
6HW3RLQW/RZ63/
+\VWHUHVLV+LJK++
+\VWHUHVLV/RZ+/
)6&DO&$/
d)
f)
g)
h)
e)
'HFLPDO3RLQWG3
i)
OPERA7,1*,16758&7,216
2. ys
, depress the MODE(S1), then the
66666
6W3W
0RGHO65
63+oint High 1
oint High 1
w 1
If S4 is
olatile
63/w 1
w 1 to the
63+oint High 2
oint High 2 to the
63/w 2
w 2 to the
++alue of Hysteresis High will
Hysteresis High to the
+/
&$/umber will be
Proceed to
G3y the current decimal position will be
Use S2 to set the decimal point to the desired
xit the Mode Selection Sequence and enter
This
is
that the
&$/,%5$7,21,16758&7,216
The
alues) are
Oing the
ut does
566(5,$/&20081,&$7,216
6:D6:E
6:F
6:G
&RPPDQG6\QWD[
8QOHVV2WKHUZLVH6SHFLILHG
566(5,$/&20081,&$7,216
6(7&200$1'35272&2/)81&7,21
[Z] [CR] [LF] Zero the displ
[F] [CR] [LF] Calibr
is scaled to displa
Set Full Scale displa
(counts
alue] [CR] [LF] Set decimal position
1 = x.xxxx
2 = xx.xxx
3 = xxx.xx
4 = xxxx.x
5 = xxxxx
alue] [CR] [LF] Set l
[P2] [vlue] [CR] [LF]
lue] [CR] [LF]
lue] [CR] [LF]
[H1] [counts] [CR] [LF] Set Lo Alar
[H2] [counts] [CR] [LF]
5($'&200$1'3527OCOL )81&7,21 5(78510(66$*(
lue
Full Scale displa
[R9] [CR] [LF]
1 = x.xxxx
2 = xx.xxx
3 = xxx.xx
4 = xxxx.x
5 = xxxxx
[R1] [CR] [LF] el
el
el
[P4] [v
[R6] [CR] [LF] Lo Alarysteresis
ysteresis
[RX] [CR] [LF] lue
nor
it will not respond to RS-232 commands or quer
Other CCR Power Supply manuals
Popular Power Supply manuals by other brands
ZALMAN
ZALMAN ZM1000-HP user manual
Texas Instruments
Texas Instruments UCD3138 Technical reference manual
Agilent Technologies
Agilent Technologies E3634A Service guide
Sherlotronics
Sherlotronics 3.2AMP installation instructions
Ultra Power
Ultra Power UP6 instruction manual
Elster Instromet
Elster Instromet FE260 Operating Manual and Installation Instructions
