Central Pneumatic CENTRAL PNEUMATIC 95499 Parts list manual

PANCAKE AIR COMPRESSOR
2 HP - 4 GALLON
Model 95499
ASSEMBLY AND OPERATION INSTRUCTIONS
CAUTION!
Your Warranty Is Voided If:
You do not puta. compressor oil in the Compressor’s crankcase prior to its first use.
Before each use, check the oil level. Never run the Compressor with low or no compressor oil.
Running the Compressor with low or no oil will permanently damage the unit.
Youb. drop the Air Compressor.
Always lift the Air Compressor using its Handle.
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright©2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor
FreightTools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements,
actual product may differ slightly from the product described herein. Tools required for assembly and service
may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09j

Page 2SKU 95499 For technical questions, please call 1-800-444-3353.
07b, 07e; 09g
SPECIFICATIONS
Electrical Requirements 120 V~ / 60 Hz / 2 HP Motor / 3400 RPM
14 Rated Amps
Power Cord Type: 14 AWG x 3 C x 6’10-1/2” Long
Power Plug Type: 3 Prong Grounded
Pressure Switch Type: ON/OFF (Pull/Push)
Compressor Style Pancake Round Tank
Pump Style Single Cylinder
Maximum Air Pressure 115 PSI
Air Flow Capacity 5.8 SCFM @ 40 PSI
4.4 SCFM @ 90 PSI
Auto Turn On/Shut Off Pressure On @ 85 PSI / Pressure Off @ 115 PSI
Air Tank Capacity 4 Gallons
Air Outlet Size 1/4”-18 NPT Female Threads
Recommended Oil Type SAE 15W-30W Non-Detergent Compressor Oil
Overall Dimensions 15-3/4” Diameter x 21” High
Weight 50 lb.
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, oper-
ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep this manual and invoice in a safe and dry place for future reference.
GENERAL SAFETY RULES AND PRECAUTIONS
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit.1. Cluttered benches and dark areas invite
accidents.
Do not operate air compressors in explosive atmospheres, such as in the2.
presence of flammable liquids, gases, or dust. Air Compressors create sparks
which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating an air tool.3. Dis-
tractions can cause you to lose control. Protect others in the work area from debris
such as chips and sparks. Provide barriers or shields as needed. Children should
not be allowed in the work area.

Page 3SKU 95499 For technical questions, please call 1-800-444-3353.
PERSONAL SAFETY
Stay alert. Watch what you are doing, and use common sense when operating1.
an air tool. Do not use an air tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating air tools may
result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.2.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the Pressure Switch (63) is in its “STOP”3.
position, all pressure is safely released, and the unit is unplugged before
moving the Compressor and before performing any service, maintenance, or
cleaning procedures on the unit.
Remove adjusting keys or wrenches before turning the Compressor on.4. A
wrench or a key that is left attached to a rotating part of the machine may result in
personal injury.
Do not overreach. Keep proper footing and balance at all times.5. Proper footing
and balance enables better control of the air tool in unexpected situations.
Use safety equipment. Always wear eye protection.6. Always wear ANSI-approved
safety impact glasses and hearing protection under a full face shield during use.
TOOL USE AND CARE
Do not force the tool. Use the correct tool for your application.1. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the Compressor if the Compressor’s Pressure Switch (63) does2.
not turn it on or off. Any tool that cannot be controlled with its Pressure Switch is
dangerous and must be replaced.
Store idle tools out of reach of children and other untrained persons.3. Tools
are dangerous in the hands of untrained users.
Maintain tools with care.4. Properly maintained tools are less likely to bind and are
easier to control. Do not use a damaged tool. Tag damaged tools “Do not use”
until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and any5.
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your6.
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.

Page 4SKU 95499 For technical questions, please call 1-800-444-3353.
SERVICE
Tool service must be performed only by qualified repair personnel.1. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instruc-2.
tions in the “Inspection, Maintenance, And Cleaning” section of this manual.
Use of unauthorized parts or failure to follow maintenance instructions may create
a risk of electric shock or injury.
SPECIFIC SAFETY RULES AND PRECAUTIONS
CAUTION!1. Your Warranty is voided if:
You do not puta. compressor oil in the Compressor’s crankcase prior to
its first use. Before each use, check the oil level. Never run the Compressor
with low or no compressor oil. Running the Compressor with low or no oil will
permanently damage the unit.
Youb. drop the Air Compressor. Always lift the Air Compressor using its Han-
dle.
DANGER! This Air Compressor is NOT equipped and should not be used2.
“as-is” to supply breathing air. For any application of air for human consump-
tion, you must fit the Air Compressor with suitable in-line safety and alarm equip-
ment (not included). This additional equipment is necessary to properly filter and
purify the air to meet minimal specifications for Grade D breathing as described
in Compressed Gas Association Commodity Specification G 7.1-1966, OSHA 29
CFR 1910. 134, and/or Canadian Standards Associations (CSA). In the event the
Air Compressor is used for the purpose of breathing air application and proper in-
line safety and alarm equipment is not simultaneously used, existing warranties
are void, and Harbor Freight Tools disclaims any liability whatsoever for any loss,
personal injury, or damage.
DANGER!3. Never attempt to repair or modify the Air Tank (50). Welding, drilling,
or any other modification will weaken the Tank resulting in damage from rupture or
explosion. Always replace worn, cracked, or damaged Tanks.
Maintain labels and nameplates on the Air Compressor.4. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
WARNING!5. Never use plastic (PVC) pipe for compressed air; serious injury or death
could result. Any tube, pipe, or hose used must have a pressure rating higher than
150 PSI. Minimum recommended pipe size: Up to 50 feet long use 1/2” diameter.
Greater than 50 feet use 3/4” diameter. Larger diameter pipe is always better.

Page 5SKU 95499 For technical questions, please call 1-800-444-3353.
Make sure all tools and equipment used with the Air Compressor are rated to6.
the appropriate capacity. Do not use any tool or equipment that does not operate
from 85 PSI to 115 PSI.
Drain the Air Compressor every day.7. Do not allow excessive moisture to build
up inside the Air Compressor’s Tank. Do not open the Drain Valve (54) with more
than 10 PSI of air pressure in the Tank. Do not unscrew the Drain Valve so that
more than four threads are showing.
Avoid injury.8. Never direct the Air Outlet Valve (67) at people or animals.
Do not alter or remove the Safety Release Valve (61).9.
Make sure the Air Compressor is located on a flat, level, sturdy surface capable10.
of supporting the weight of the Compressor, operator(s), and any additional
tools and equipment.
Do not move or transport the Compressor if the Air Tank (50) is under pres-11.
sure.
Industrial applications must follow OSHA guidelines.12.
Never stand on the Air Compressor.13. Serious injury could result if the Compres-
sor is tipped.
Never leave the Air Compressor unattended when it is plugged in and running.14.
Turn off the Compressor, and unplug the unit before leaving.
Do not allow children and other unauthorized people to handle or play with15.
the Air Compressor.
Do not modify the factory set pressure shutoff or startup switches.16. This tool will
do the work better and safer at the speed and capacity for which it was designed.
Avoid body contact with oils and lubricants used in the Compressor.17. If swal-
lowed, seek medical treatment immediately. For skin contact, immediately wash
with soap and water. For eye contact, immediately flush eyes with clean water.
WARNING: The brass components of this product contain lead, a chemical18.
known to the State of California to cause birth defects (or other reproductive
harm). (California Health & Safety code § 25249.5, et seq.)
People with pacemakers should consult their physician(s) before use.19. Elec-
tromagnetic fields in close proximity to heart pacemaker could cause pacemaker
interference or pacemaker failure.
WARNING!20. The warnings and precautions discussed in this manual cannot cover
all possible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
07d

Page 6SKU 95499 For technical questions, please call 1-800-444-3353.
SAVE THESE INSTRUCTIONS
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool.
Never remove the grounding prong from the plug. Do not use the tool if the
power cord or plug is damaged. If damaged, have it repaired by a service facil-
ity before use. If the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1. Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a
properly grounded outlet. If the tool should electri-
cally malfunction or break down, grounding pro-
vides a low resistance path to carry electricity away
from the user, reducing the risk of electric shock.
(See 3-Prong Plug and Outlet.)
The grounding prong in the plug is connected2.
through the green wire inside the cord to the
grounding system in the tool. The green wire in the
cord must be the only wire connected to the tool’s
grounding system and must never be attached to an electrically “live” terminal. (See
3-Prong Plug and Outlet.)
Your tool must be plugged into an appropriate outlet, properly installed and grounded3.
in accordance with all codes and ordinances. The plug and outlet should look like
those in the following illustration. (See 3-Prong Plug and Outlet.)
3-Prong Plug and Outlet

Page 7SKU 95499 For technical questions, please call 1-800-444-3353.
SYMBOLOGY
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~ Volts Alternating Current
AAmperes
n0xxxx/min. No Load Revolutions per Minute (RPM)
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page
13 are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.

Page 8SKU 95499 For technical questions, please call 1-800-444-3353.
ASSEMBLY INSTRUCTIONS
CAUTION!1. Always make sure the Compressor’s Pressure Switch (63) is in its
“STOP” position prior to performing any service, maintenance, or cleaning of the
Compressor.
2.
REGULATOR
OILER WATER
FILTER
TO
TOOL
AIR
COMPRESSOR
FIGURE C
To extend the life of your tools and equipment, it is recommended that you install
an oiler and water filter in-line with the Air
Outlet Valve (67) of the Air Compressor.
(See Figure C.)
Prior to using the Air Compressor, the unit3.
requires the attachment of a 1/4”-18 NPT
Female Quick Connector (not included). To
do so, wrap approximately 3” of pipe thread
sealant tape (not included) around the male
threads of the Air Outlet Valve (67). Then
firmly screw the Quck Connector into the Air
Outlet Valve (67). (See Figure D.)
QUICK
CONNECTOR
(NOT INCLUDED)
AIR OUTLET
VALVE (67)
FIGURE D
07d

Page 9SKU 95499 For technical questions, please call 1-800-444-3353.
PRE-START INSTRUCTIONS – Adding Compressor Oil
IMPORTANT!1. Prior to first using the Compressor, the Compressor MUST be filled
with a high quality S.A.E. 15W-30W grade non-detergent compressor oil.
OIL SIGHT GLASS
(21)
OIL BREATHER CAP
(24)
FIGURE E
DESIRED LEVEL
2. To do so, unscrew and remove the Oil Breather Cap (24). Pour approximately 1/2
quart of compressor oil into the Oil Breather Cap hole. Do not overfill.
(See Figure E.)
Observe the level of compressor oil through the Oil Sight Glass (21). The optimal3.
oil level is at the center of the glass.
When finished adding compressor oil, re-install the Oil Breather Cap (24) back into4.
the Oil Breather Cap hole. (See Figure E.)

Page 10SKU 95499 For technical questions, please call 1-800-444-3353.
OPERATING INSTRUCTIONS
To Start The Compressor:
TOOL PRESSURE
GAUGE (65)
SAFETY RELEASE
VALVE (61)
REGULATOR (66)
ATTACH AIR HOSE HERE
TANK DRAIN VALVE (54)
TANK PRESSURE
GAUGE (62)
PRESSURE SWITCH
(63)
AIR OUTLET
VALVE (67)
FIGURE F
1. Check to make sure the Air Tank’s Drain Valve (54), located at the bottom of the Air
Tank (50), is fully closed. Pull on the Safety release valve to verify that it is unstuck.
(See Figure F.)
Turn the Air Outlet Valve (67) to its2. closed position. (See Figure F.)
Connect an air hose (not included) to the previously installed Quick Connector.3.
Then, connect the other end of the air hose to the pneumatic tool (not included)
that is to be used. (See Figure F, next page.)
Plug the Power Cord (55) into the nearest 120 volt, grounded, electrical outlet.4.
Pull5. up on the Pressure Switch (63) to its “START” position to turn on the unit.
(See Figure F.)
When the Tank Pressure Gauge (62) reaches at least6. 85 PSI, turn the Air Outlet
Valve to its open position to allow air to the pneumatic tool. (See Figure F.)
Once the air pressure reaches the pneumatic tool, observe the Tool Pressure Gauge7.
(65). Adjust the Regulator (66) to feed the proper PSI to the tool. To do so, turn
the Regulator clockwise to increase the PSI. Turn the Regulator counterclockwise
to decrease the PSI. (See Figure F.)
NOTE:8. When the maximum air pressure,115 PSI, is reached as indicated by the
Tank Pressure Gauge (62), the motor will stop. The Compressor will automatically
restart when the air pressure drops below 85 PSI. (See Figure F.)
07d