Central Pneumatic PROFESSIONAL 99901 User manual

PORTABLE COMPRESSED
CO2REGULATOR
99901
OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.

SKU 99901 For technical questions, please call 1-800-444-3353. Page 2
SAVE THIS MANUAL
Keep this manual for the safety warn-
ings and precautions, assembly, operating,
inspection, maintenance and cleaning pro-
cedures. Write the product’s serial number
in the back of the manual (or month and
year of purchase if product has no num-
ber). Keep this manual and the receipt in
a safe and dry place for future reference.
Safety Alert Symbol and Signal
Words
In this manual, on the labeling,
and all other information provid-
ed with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
IMPORTANT SAFETY
INSTRUCTIONS
INSTRUCTIONS PERTAINING
TO A RISK OF FIRE,
ELECTRIC SHOCK, OR
INJURY TO PERSONS
WARNING – When using regulators, basic
precautions should always be fol-
lowed, including the following:
General
To reduce the risks of electrica.
shock, re, and injury to persons,
read all the instructions before us-
ing the regulator.
Work area
Keep the work area clean and wella.
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, re, and injury to persons.
Keep bystanders, children, andb.
visitors away while operating the
regulator. Distractions are able to
result in the loss of control of the
regulator.

SKU 99901 For technical questions, please call 1-800-444-3353. Page 3
Personal safety
Stay alert. Watch what you are do-a.
ing and use common sense when
operating the regulator. Do not
use the regulator while tired or un-
der the inuence of drugs, alcohol,
or medication. A moment of inatten-
tion while operating the regulator in-
creases the risk of injury to persons.
Avoid unintentional starting. Beb.
sure the tool switch is off before
connecting to the CO2Regulator.
Do not connect the tool to the CO2
Regulator with the switch on.
c. Always wear eye protec-
tion. Wear ANSI-ap-
proved safety goggles.
d. Always wear hearing
protection when using
the regulator. Prolonged
exposure to high intensity
noise is able to cause hearing loss.
Regulator use and care
Use only with tools specically de-a.
signed for use with bottled gasses.
Read tool manual before connec-b.
tion and/or use.
Assemble, use and store in a well-c.
ventilated area only. Carbon dioxide
gas is invisible and odorless can ac-
cumulate in conned spaces.
Use with carbon dioxide gas only.d.
Attach the Hose properly to thee.
Regulator and tool before use. A
loose Hose may detach or break dur-
ing operation.
Do not use the regulator if thef.
Regulator Control Knob does not
function properly. Any regulator that
cannot be controlled is dangerous
and must be repaired.
Disconnect the tool from the COg. 2
Regulator before making any ad-
justments, changing accessories,
or storing the tool. Such preventive
safety measures reduce the risk of
starting the tool unintentionally. Turn
off and detach the CO2supply, safely
discharge any residual pressure, and
release the throttle and/or turn the
switch to its off position before leav-
ing the work area.
Store the regulator and gas canis-h.
ter when idle out of reach of chil-
dren and other untrained persons.
A regulator is dangerous in the hands
of untrained users.
Do not exceed 150 PSI input pres-i.
sure.
WARNING: The brass compo-j.
nents of this product contain lead,
a chemical known to the State of
California to cause birth defects
(or other reproductive harm).
(California Health & Safety code
25249.5, et seq.)
The warnings and precautionsk.
discussed in this manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are fac-
tors which cannot be built into this
product, but must be supplied by the
operator.

SKU 99901 For technical questions, please call 1-800-444-3353. Page 4
Service
Regulator service must be per-a.
formed only by qualied repair
personnel. Replacement parts are
not available for this product. Discard
product if it cannot be repaired by
technician.
Inspect before every use; do notb.
use if parts are loose or damaged.
SAVE THESE
INSTRUCTIONS.
Symbol Denitions
Symbol Property or statement
PSI Pounds per square inch of pressure
CFM Cubic Feet per Minute ow
SCFM Cubic Feet per Minute ow at
standard conditions
NPT National pipe thread, tapered
NPS National pipe thread, straight
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
eye protection.
WARNING marking concerning Risk
of Hearing Loss. Wear hearing
protection.
WARNING marking concerning Risk
of Respiratory Injury. Wear NIOSH-
approved dust mask/respirator.
WARNING marking concerning Risk
of Explosion.

SKU 99901 For technical questions, please call 1-800-444-3353. Page 5
SPECIFICATIONS
Maximum Input
Pressure 150 PSI
CO2Inlet 1/2” -14 TPI
CO2Bottle Size Standard 20 Oz. size with
1/2” x 14 TPI Thread
Hose Fittings Female Quick Connectors
UNPACKING
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown throughout the manual as soon as
possible.
This product may be shipped with a•
protective plug covering the air inlet/
outlet. Remove this plug before set
up.
OPERATION
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
TO PREVENT
SERIOUS INJURY
AND DEATH:
The work, setup, and storage
areas must all be well
ventilated. CO2is an invisible
odorless gas which can cause
serious injury or death if it
accumulates.
TO PREVENT
EXPLOSION:
Use only clean, dry, bottled,
compressed CO2with this
regulator. Do not use oxygen
or any other gas.
TO PREVENT
SERIOUS INJURY:
Do not adjust any control or
component in a way not
specically explained within
this manual. Improper
adjustment can result in
regulator failure or other
serious hazards.
Regulator Control Knob
Output Gas Pressure Dial
Female Hose
Quick Connector
Belt Hook
1. Close the Regulator Control Knob
completely by turning it counterclock-
wise.
REV 09c

SKU 99901 For technical questions, please call 1-800-444-3353. Page 6
CO2Canister Connector
Bottom View of Item
Regulator Knob
Female Output Connector
Belt Hook
2. Insert a standard 20 oz. CO2bottle
(not included) into the opening at the
bottom of the regulator. Turn the
canister clockwise to screw it into the
Connector. Tighten rmly to prevent
leaks.
Adjust the Regulator Control Knob so 3.
that the air output is enough to prop-
erly power the tool, but the output
will not exceed the tool’s maximum
air pressure at any time. Adjust the
pressure gradually, while checking
the air output gauge to set the right
pressure range.
Inspect the air connections for leaks.4.
Tighten connections to eliminate
leaks.
Connect Hose to tool (not included)5.
by pressing coupler onto inlet.
The CO6. 2Regulator has a built in
hook that can be used to hang it from
a belt.
Connect the Hose to the CO7. 2Regu-
lator by pressing it onto the outlet.
The pressure supplied to the tool can8.
be adjusted by turning the Regulator
Control Knob. Turn counterclockwise
to reduce pressure. Turn clockwise
to increase pressure. The pressure
setting is shown on the Output Gas
Pressure Dial.
Adjust the Regulator knob to the 9.
pressure recommended by the tool
manufacturer. Do not exceed the
tool’s maximum air pressure rat-
ing.
Note: Residual air pressure should not be
present after the tool is disconnected
from the CO2supply. However, it is
a good safety measure to attempt to
discharge the tool in a safe fashion
after disconnecting to ensure that the
tool is disconnected and unpowered.
As the contents of your CO10. 2canister
are used up, the available pressure
will decrease. Available pressure will
eventually fall below your regulator
setting. The dial will show a lower
pressure reading than desired. When
pressure is no longer adequate,
replace the CO2Canister. Dispose
of used canisters according to solid
waste disposal instructions.
To prevent accidents, turn off the tool,11.
detach the CO2Regulator from tool
and canister, and safely discharge
any residual air pressure in the tool
after use.
REV 09c

SKU 99901 For technical questions, please call 1-800-444-3353. Page 7
USER-MAINTENANCE
INSTRUCTIONS
Procedures not specically
explained in this manual
must be performed only by a
qualied technician.
Detach tool and CO2 canister, then1.
clean external surfaces of the regula-
tor with clean, dry cloth.
Store the regulator indoors out of2.
children’s reach.
Note: Since this regulator is not user-
serviceable, no assembly diagram or
parts list are available for this tool.
Troubleshooting
Problem Possible Causes Likely Solutions
Decreased output. Not enough air pressure and/1.
or air ow.
Air leaking from loose hose2.
connection.
Mechanism contaminated.3.
CO4. 2pressure is low or
depleted.
Check for loose connections and make sure1.
that regulator is set at required pressure.
Do not exceed maximum air pressure.
Make sure hose is properly connected and2.
tight.
Have qualied technician clean mechanism. 3.
Replace CO4. 2canister.
Severe air
leakage.
(Slight air leakage
is normal,
especially on older
tools.)
Cross-threaded components.1.
Incorrectly installed CO2. 2
canister.
Damaged valve or hose.3.
Check for incorrect alignment and uneven1.
gaps. If cross-threaded, disassemble and
replace damaged parts before use.
Reinstall if cross threaded. Tighten if2.
loose. Make sure o-ring is in place at top of
regulator threaded connection.
Replace or repair damaged hose. Have3.
qualied technician repair valve.
Follow all safety precautions whenever diagnosing or servicing the
tool. Disconnect air supply before service.

SKU 99901 For technical questions, please call 1-800-444-3353. Page 8
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
LIMITED 1 YEAR WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of one year from the
date of purchase. This warranty does not apply to damage due directly or indirectly, to
misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, nor-
mal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential
damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclu-
sion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MER-
CHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection veries the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]