Central Pneumatic 98635 Installation manual

AIR COMPRESSOR
6 GAL. - 2 HP
98635
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09k

SKU 98635 For technical questions, please call 1-800-444-3353. Page 2
SAVE THIS MANUAL
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information provid-
ed with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Safety Warnings
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future reference.
1. Work area safety
Keep work area clean and well lit.a.
Cluttered or dark areas invite acci-
dents.
Do not operate power tools inb.
explosive atmospheres, such as in
the presence of ammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust or
fumes.
Keep children and bystandersc.
away while operating a power tool.
Distractions can cause you to lose
control.
Electrical safety2.
Power tool plugs must match thea.
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with grounded power tools.
Unmodied plugs and matching out-
lets will reduce risk of electric shock.
Avoid body contact with groundedb.
surfaces such as pipes, radiators,
ranges and refrigerators. There is

SKU 98635 For technical questions, please call 1-800-444-3353. Page 3
an increased risk of electric shock if
your body is grounded.
Do not expose power tools to rainc.
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never used.
the cord for pulling or unplugging
the power tool. Keep cord away
from heat, oil, sharp edges or mov-
ing parts. Damaged or entangled
cords increase the risk of electric
shock.
If operating a power tool in a dampe.
location is unavoidable, use a
Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of
a GFCI reduces the risk of electric
shock.
Personal safety3.
Stay alert, watch what you are do-a.
ing and use common sense when
operating a power tool. Do not use
a power tool while you are tired
or under the inuence of drugs,
alcohol or medication. A moment
of inattention while operating power
tools may result in serious personal
injury.
Use personal protective equip-b.
ment. Always wear ANSI-approved
safety goggles. Safety equipment
such as NIOSH-approved dust mask,
non-skid safety shoes, hard hat, or
hearing protection used for appropri-
ate conditions will reduce personal
injuries.
Prevent unintentional starting.c.
Ensure the switch is in the off-po-
sition before connecting to power
source, picking up or carrying the
tool. Carrying power tools with your
nger on the switch or energizing
power tools that have the switch on
invites accidents.
Remove any adjusting key ord.
wrench before turning the power
tool on. A wrench or a key left at-
tached to a rotating part of the power
tool may result in personal injury.
Do not overreach. Keep propere.
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear loosef.
clothing or jewelry. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewelry or long hair can be caught in
moving parts.
Power tool use and care4.
Do not force the power tool. Usea.
the correct power tool for your ap-
plication. The correct power tool will
do the job better and safer at the rate
for which it was designed.
Do not use the power tool if theb.
switch does not turn it on and off.
Any power tool that cannot be con-
trolled with the switch is dangerous
and must be repaired.
Disconnect the plug from thec.
power source before making any
adjustments, changing accesso-
ries, or storing power tools. Such
preventive safety measures reduce
the risk of starting the power tool ac-
cidentally.
Store idle power tools out of thed.
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to oper-
ate the power tool. Power tools are

SKU 98635 For technical questions, please call 1-800-444-3353. Page 4
dangerous in the hands of untrained
users.
Maintain power tools. Check fore.
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If dam-
aged, have the power tool repaired
before use. Many accidents are
caused by poorly maintained power
tools.
Use the power tool and acces-f.
sories in accordance with these
instructions, taking into account
the working conditions and the
work to be performed. Use of the
power tool for operations different
from those intended could result in a
hazardous situation.
Service5.
Have your power tool serviced bya.
a qualied repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
Compressor Safety Warnings
Maintain labels and nameplates on1.
the Compressor. These carry impor-
tant safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
Avoid unintentional starting. Prepare2.
to begin work before turning on the
Compressor.
Do not leave the Compressor unat-3.
tended when it is plugged into an
electrical outlet. Turn off the Com-
pressor, and unplug it from its electri-
cal outlet before leaving.
This product is not a toy. Keep it out4.
of reach of children.
People with pacemakers should5.
consult their physician(s) before use.
-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure. In addition, people with
pacemakers should:


on.

avoid electrical shock.

grounded. Ground Fault Circuit Inter-
rupter (GFCI) should also be imple-
mented – it prevents sustained elec-
trical shock.
WARNING: Handling the cord on6.
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
WARNING: This product contains7.
brass, which is a chemical known to
the State of California to cause can-
cer and birth defects and other repro-
ductive harm. (California Health &
Safety Code § 25249.5, et seq.)
CAUTION: Your Warranty is voided8.
if:
You do not put compressor oil in thea.
Compressor’s crankcase prior to its

the oil level. Never run the Com-
pressor with low or no compressor
oil. Running the Compressor with

SKU 98635 For technical questions, please call 1-800-444-3353. Page 5
low or no oil will permanently dam-
age the unit.
You drop the Compressor. Alwaysb.
lift the Compressor using its handle.
DANGER: This Compressor is NOT9.
equipped and should not be used “as
is” to supply breathing quality air. For
any application of air for human con-
-
sor with suitable in-line safety and
alarm equipment (not included). This
additional equipment is necessary


D breathing as described in Com-
pressed Gas Association Commodity

CFR 1910. 134, and/or Canadian
Standards Associations (CSA). In the
event the Compressor is used for the
purpose of breathing air application
and proper in-line safety and alarm
equipment is not simultaneously
used, existing warranties are void,
and Harbor Freight Tools disclaims
any liability whatsoever for any loss,
personal injury, or damage.
WARNING: Never attempt to re-10.
pair or modify the air tank. Welding,

weaken the tank resulting in damage
from rupture or explosion. Always
replace worn, cracked, or damaged
tanks.
WARNING: Never use plastic (PVC)11.
pipe for compressed air. Serious
injury or death could result. Any
tube, pipe, or hose used must have a
pressure rating higher than 150 PSI.
Minimum recommended pipe size:
Up to 50 feet long use 1/2” diameter.
Greater than 50 feet use 3/4” diam-
eter. Larger diameter pipe is always
better.
Make sure all tools and equipment12.
used with the Compressor are rated
to the appropriate capacity. Do not
use any tool or equipment that does
not operate from 85 PSI to 115 PSI.
Drain the Compressor every day. Do13.
not allow excessive moisture to build
up inside the air tank. Do not open
the drain valve with more than 10 PSI
of air pressure in the tank. Do not
unscrew the drain valve so that more
than four threads are showing.
Avoid injury. Never direct the air out-14.
let valve at persons or animals.
Do not alter or remove the safety15.
valve.
Make sure the Compressor is lo-16.

capable of supporting the weight of
the Compressor, operator(s), and any
additional tools and equipment.
Industrial applications must follow17.
OSHA guidelines.
Never stand on the Compressor.18.
Serious injuty could result if the Com-
pressor is tipped.
Do not move or transport the Com-19.
pressor if the tank is under pressure.
Avoid contact with oils and lubricants20.
used in the Compressor. If swal-
lowed, seek medical attention imme-
diately. For eye contact, immediately

The warnings, precautions, and in-21.
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.

SKU 98635 For technical questions, please call 1-800-444-3353. Page 6
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
SAVE THESE INSTRUCTIONS.
GROUNDING
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM
INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualied
electrician if you are in doubt
as to whether the outlet is
properly grounded. Do not
modify the power cord plug
provided with the tool. Never
remove the grounding prong
from the plug. Do not use the
tool if the power cord or plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the plug will not
t the outlet, have a proper
outlet installed by a qualied
electrician.
Grounded Tools: Tools with Three
Prong Plugs
Tools marked with “Grounding Re-1.
quired” have a three wire cord and
three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the tool should
electrically malfunction or break
down, grounding provides a low
resistance path to carry electricity
away from the user, reducing the risk
of electric shock. (See 3-Prong Plug
and Outlet.)
The grounding prong in the plug is2.
connected through the green wire in-
side the cord to the grounding system
in the tool. The green wire in the cord
must be the only wire connected to
the tool’s grounding system and must
never be attached to an electrically
“live” terminal. (See 3-Prong Plug
and Outlet.)
The tool must be plugged into an3.
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-Prong
Plug and Outlet.)
Double Insulated Tools: Tools
with Two Prong Plugs
Tools marked “Double Insulated” do1.
not require grounding. They have
a special double insulation system
This Compressor
Uses A
3-Prong Plug

SKU 98635 For technical questions, please call 1-800-444-3353. Page 7

and complies with the applicable
standards of Underwriters Labora-
tories, Inc., the Canadian Standard
Association, and the National Electri-
cal Code. (See Outlets for 2-Prong
Plug.)
Double insulated tools may be used2.
in either of the 120 volt outlets shown
in the preceding illustration. (See
Outlets for 2-Prong Plug.)
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~ Volts Alternating Current
AAmperes
n0xxxx/min. No Load Revolutions per Minute
(RPM)
SPECIFICATIONS
Electrical Requirements
120 V~ / 60 Hz / 2.0 HP Motor
21.8 Start-Up Amps
9.3 No Load Amps
Motor RPM: 3400
Power Cord: 14AWGx3C
Plug: 3-Prong, Grounded
Maximum Pressure 115 PSI
Pump SCFM Maximum 6.1 CFM @ 40 PSI
3.8 CFM @ 90 PSI
Air Tank Capacity 6.34 Gallons
Tank Air Outlet Size 1/4”-18 NPT
Automatic
Start Up & Shut Off 85 PSI Start Up / 115 PSI Shut Off
Safety Valve Maximum
Pressure Rating 130 PSI
Crankcase Oil Type 

Oil Capacity 8.5 ounces
UNPACKING
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch (60) of
the Compressor to its “OFF”
position and unplug the
Compressor from its electrical
outlet before set up or use of
the tool.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
1.
Compressor, the Compressor MUST

compressor oil (not included).
-a.
peratures over
-b.
atures under
2.
(26). (See Figure A, next page.)
REV 08k, 09a

SKU 98635 For technical questions, please call 1-800-444-3353. Page 8
Observe the level of oil through the3.
Oil Sight Glass (23). The oil level
should appear between the “MINI-
MUM” and “MAXIMUM” marks on the
Sight Glass.
(See Figure A.)
4.
(26), while checking the Oil Sight
Glass (23), until the oil level reaches
the “MAXIMUM” mark on the Sight
Glass. Do not exceed the “MAXI-
MUM” mark on the Sight Glass.
(See Figure A.)
5.

(See Figure A.)
BREATHER
(26)
OIL SIGHT GLASS
(23)
FIGURE A
Incorporate an in-line oiler, shut-off6.
valve, regulator with pressure gauge,

the diagram on the next page. An in-
line shutoff valve is an important
safety device because it controls
the air supply even if the air hose
is ruptured. (See Figure B.)
Tool
Air
Compressor
Quick
Coupler Air Hose
on Reel
Filter
Regulator with
Pressure Gauge
Male
Connector
Male
Connector
Valve
Quick
Coupler
Attach an air hose to the Compres-7.
sor’s Quick Coupling (63). Then con-
nect the other end of the air hose to
the air inlet of the pneumatic tool.
Close the in-line safety valve be-8.
tween the Compressor and the tool.
Turn on the Compressor according9.
to the directions in this manual and
allow it to build up pressure until it
cycles off at 115 PSI.
Adjust the Compressor’s Tool Pres-10.
sure Gauge (64) so that the air output
is enough to properly power the tool,
but the output will not exceed the
tool’s maximum air pressure at any
time. Adjust the pressure gradually,
not to exceed the maximum working
pressure.
Inspect the air connections for leaks.11.
Repair any leaks found.
If the tool will not be used at this12.
time, turn off and detach the air sup-
ply, safely discharge any residual
air pressure, and release the tool’s
throttle and/or turn the switch to its off
FIGURE B

SKU 98635 For technical questions, please call 1-800-444-3353. Page 9
position to prevent accidental opera-
tion.
Note: Residual air pressure should not be
present after the tool is disconnected
from the air supply. However, it is a
good safety measure to attempt to
discharge the tool in a safe fashion
after disconnecting to ensure that the
tool is disconnected and unpowered.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch (60) of
the Compressor to its “OFF”
position and unplug the tool
from its electrical outlet
before performing any
inspection, maintenance, or
cleaning procedures.
Work Piece and Work Area Set Up
Designate a work area that is clean1.
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
Route the Power Cord (67) and air2.
hose along a safe route to reach the
work area without creating a tripping
hazard or exposing the Power Cord
or air hose to possible damage. The
Power Cord and air hose must reach
the work area with enough extra
length to allow free movement while
working.
There must not be hazardous ob-3.
jects, such as utility lines or foreign
objects, nearby that will present a
hazard while working.
The Air Compressor should be po-4.

preferably in a dry location.
General Operating Instructions
Check to make sure the Compres-1.
sor’s Drain Valve (53), located at the
bottom of the Tank (1) is fully closed.
(See Figure C, next page.)
FIGURE C
DRAIN VALVE
(53)
2. Turn the Air Outlet Valve on the Reg-
ulator Assembly (62) to its “CLOSED”
position. (See Figure D.)

SKU 98635 For technical questions, please call 1-800-444-3353. Page 10
FIGURE D
AIR OUTLET VALVE
3. Press down on the Power Switch (60)
to its “OFF” position.
(See Figure E.)
FIGURE E
POWER SWITCH
(60)
4. Plug the Power Cord (67) into the
nearest 120 volt, grounded outlet.
Pull up on the Power Switch (60) to5.
its “START” position to turn on the
Compressor. (See Figure E.)
When the Tank Pressure Gauge (65)6.
reaches at least 85 PSI, turn the Air
Outlet Valve on the Regulator As-
sembly (62) to its “OPEN” position to
allow air to the pneumatic tool.
(See Figures F and E.)
FIGURE F
TANK
PRESSURE
GAUGE
(65)
TOOL
PRESSURE
GAUGE
(64)
REGULATOR
(62)
AIR
OUTLET
VALVE
(62)
Once air pressure reaches the pneu-7.
matic tool, observe the Tool Pressure
Gauge (64). Adjust the Regulator (62)
to feed the proper PSI to the tool. To
do so, turn the Regulator clockwise to
increase PSI to the tool. Turn the Reg-
ulator counterclockwise to decrease
the PSI. (See Figure F.)
When the Compressor’s maximum air8.
pressure, 115 PSI, is reached as in-
dicated by the Tank Pressure Gauge
(65), the unit will automatically switch
to idle and the Compressor will stop
building pressure. The Compressor
will automatically restart when the
Tank’s air pressure drops below 85
PSI. (See Figure F.)
IMPORTANT: The Safety Valve (59) is9.
used when decompression is needed

the air pressure in the Tank (1), push
down on the Power Switch (60) to its
“STOP” position. Then, pull out on the
Safety Valve to immediately release air
pressure from the Tank.
(See Figure F.)

SKU 98635 For technical questions, please call 1-800-444-3353. Page 11
FIGURE F
SAFETY VALVE
(59)
10. 
push down on the Power Switch (60)
to its “STOP” position.
(See Figures E and F.)
Unplug the Power Cord (67) from its11.
electrical outlet.
Remove any moisture in the Com-12.
pressor’s Tank (1) by opening the
Drain Valve (53) (no more than two
turns). Then, retighten the Drain
Valve. (See Figure C.)
Squeeze the trigger on the pneumatic13.
tool to release any remaining air pres-
sure from the tool. Then disconnect
the air hose from the tool, and store
the tool in a clean, dry, safe location
out of reach of children.
Disconnect the other end of the air14.
hose from the Quick Coupling (63)
on the Compressor and store the air
hose in a clean, dry, safe location out
of reach of children.
Allow the Compressor to completely15.
cool. Then store the unit in a clean,
dry, safe location out of reach of chil-
dren.

SKU 98635 For technical questions, please call 1-800-444-3353. Page 12
MAINTENANCE AND
SERVICING
Procedures not specically
explained in this manual
must be performed only by a
qualied technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch (60) of
the Compressor to its “OFF”
position and unplug the unit
from its electrical outlet
before performing any
inspection, maintenance, or
cleaning procedures.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
Inspection, Maintenance, and
Cleaning
1.
general condition of the Compressor.
Check for loose screws, misalignment
or binding of moving parts, cracked or
broken parts, damaged air hose, and
any other condition that may affect its
safe operation.
2.
compressor oil level in the Oil Sight
-
pressor’s Crankcase with the proper
amount and type of compressor oil.
DAILY, purge the Compressor’s Tank3.
(1) of all air and moisture to prevent
corrosion. Carefully unscrew (no
more than two turns) the Drain Valve
(53) until the compressed air and
moisture begins to be discharged

for all of the air and moisture to

retighten the Drain Valve.
AFTER USE,4. clean external surfaces
of the tool with clean cloth and mild
detergent. Do not use solvents. Do
not immersed any part of the Com-
pressor in liquid.
5. WARNING! If the Power Cord
(67) of this Compressor is dam-
aged, it must be replaced only by a
qualied service technician.
PLEASE READ THE
FOLLOWING CAREFULLY

HAS PROVIDED THE PARTS LIST AND

A REFERENCE TOOL ONLY. NEITHER THE

ANY REPRESENTATION OR WARRANTY OF

IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT.
IN FACT, THE MANUFACTURER AND/OR

ALL REPAIRS AND PARTS REPLACEMENTS




REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.

SKU 98635 For technical questions, please call 1-800-444-3353. Page 13
Power switch will not
turn off Compressor.
1. Defective power switch.
power switch.

SKU 98635 For technical questions, please call 1-800-444-3353. Page 14
PARTS LIST PARTS LIST
Part Description Part Description
1 Tank 35 Cylinder Cover
2 Hex Nut (M8) 36 Spring Washer (#6)
3 Spring Washer (#8) 37 Flat Washer (#6)
4 38 
5 Flat Washer (#8) 39 Air Filter
6 Rubber Foot 40 Cylinder Cover Gasket
7 Plastic Cowling 41 Pin
8 Tube Fan 42 Air Intake Valve
9 Rear Motor Cover 43 Valve Plate Assembly
10 Wave Washer 44 Cylinder Plate
11  45 Piston Pin
12  46 Piston
13 Spring Washer (#5) 47 Connecting Rod
14 Motor Stator 48 Capacitor
15 Motor Rotor 49 Wheel Assembly
16  50 Wheel Shaft Screw
17 Oil Seal 51 Wheel Shaft Sleeve
18 Crankcase 52 Hex Nut (M8)
19 Crank 53 Drain Valve
20  54 Outlet
21 Crankcase Cover Gasket 55 Non-Return Valve
22 Crankcase Cover 56 Discharge Valve
23 Oil Sight Glass 57 Rubber Plate
24  58 Lock Nut
25  59 Safety Valve
26  60 Power Switch Assembly
27 Circlip (#12) 61 Connector
28 Cylinder 62 Regulator Assembly
29 Spring Washer (M8) 63 Quick Coupling
30  64 Tool Pressure Gauge
31 Oil Clean Ring 65 Tank Pressure Gauge
32 Oil Seal Ring 66 Handle Sleeve
33 Valve Plate Gasket 67 Power Cord/Plug
34 Square Connector

SKU 98635 For technical questions, please call 1-800-444-3353. Page 15
ASSEMBLY DIAGRAM

SKU 98635 For technical questions, please call 1-800-444-3353. Page 16
LIMITED 1 YEAR / 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that for a period
of one year from date of purchase that the tank is free of defects in materials and work-
manship (90 days if used by a professional contractor or if used as rental equipment).
Harbor Freight Tools also warrants to the original purchaser, for a period of ninety days
from date of purchase, that all other parts and components of the product are free from
defects in materials and workmanship. This warranty does not apply to damage due di-
rectly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations out-
side our facilities, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limita-
tion of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES

To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.

which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.