Cerio ANT-10AD User manual

Installation Guide
5GHz 2x2 Outdoor IP68 Directional 10dBi Panel Pole/Wall Mount Antenna
1
CERIO Corporation
ANT-10AD
5GHz 2x2 Outdoor IP68 Directional 10dBi
Panel Pole/Wall Mount Antenna
Installation Guide
Technical Support
E-mail: [e-mail]
TEL: [phone] #222
Web Site: www.cerio.com.tw

Installation Guide
5GHz 2x2 Outdoor IP68 Directional 10dBi Panel Pole/Wall Mount Antenna
Package Contents :
ANT-10AD Main Unit x1
Adjustable Pole & Wall Mounting Kit (OW-PKUR) x1
Quick Installation Guide x1
Warranty Card x1
Main Unit Overview : (ANT-10AD )
Installation:
Mount the antenna on the brackets according to the
Mounting diagram. Make sure the ANT-10AD
antenna polarization parallel direction you needed.
When the antenna polarization are vertical to the
ground, the antenna is vertical polarized. When the
antenna polarization are horizontal to the ground,
the antenna is horizontal polarization.
1. ANT-10AD design in a horizontally- antenna,
Mount the ANT-10AD antenna on the antenna
on the mast supplied by customer according to the Mounting diagram. Make sure that
when ANT-10AD is installed as standard, the antenna points horizontally, the Horizontal
beam width is 35°, and the Vertical beam width is 30°; or when the ANT-10AD casing is
rotated 90 degrees, the antenna points horizontally, and the Horizontal beam width is 30°,
Vertical beam width is 35°.
Linear H/V :
Real
Real / with OW-PKUR
2x2 N-Type
Connector
Mounting Kit

Installation Guide
5GHz 2x2 Outdoor IP68 Directional 10dBi Panel Pole/Wall Mount Antenna
3
2. Test the antenna with the device to make sure it is receiving the best RSSI signal: turn the
azimuth and elevation, then tighten all the screws and make sure your own RF cable is
connected with a lock seal, if you bought the LLMR-NNP-1M/ 2M RF cable, you can directly
use the waterproof cap provided with LLMR-NNP-1M/2M to tightly seal the connector
between ANT-10AD RF cables.

Installation Guide
5GHz 2x2 Outdoor IP68 Directional 10dBi Panel Pole/Wall Mount Antenna
ANT-10AD back plate
1. Pole Mount (Pole Range:
Ø30-Ø90mm)
(Based on the panel antenna by side view)
Tilt angle adjustable by pole mount
Drill 4 holes on the wall with following dimensions.
2. Alternative wall mount
Unit : mm
Adjustable up/down 35° for upright mount
NO DESCRIPTION QTY
1 SUS304 Uni-axis bracket with
Hexagon socket cap screw set
1
2 SUS304 M6 Hexagon Flange Non-
slip Nut
8
3
US304 M6 U bolt 66x75mm
2
4 US304 4" Hose Clamps 2
5
Simple single open hexagonal
h
1
6 #45 carbon steel-L-shaped hex
wrench tool / 5mm
1
7 US304 M6/L18
Hexagon socket cap
4
8 US304 M6 spring washer 4
9 US304 M6 flat washer 4
10 Ni Drop in Anchors (25x6mm) 4
#4 Pole Range│Ø30-Ø90mm
#3 Pole Range│Ø34-Ø54mm
Adjustable up/down 40° for horizontal mount
35°
35°
40°
40°
3
2
1
4
6
5
8
7
9
0