Challenger Lifts Versymmetric CL9 Configuration guide

01/31/2008
INSTALLATION & OPERATION MANUAL SUPPLEMENT
7,000LB PAD ADAPTER
FOR MODELS CL9 & CL10
200 CABLE STREET, P.O. BOX 3944 LOUISVILLE, KENTUCKY 40201-3944
EMAIL: [e-mail] WEB SITE: WWW.CHALLENGERLIFTS.COM
OFFICE 800-648-5438 / 502-625-0700 FAX [phone]
IMPORTANT:READ THIS MANUAL COMPLETELY BEFORE INSTALLING OR
OPERATING LIFT
Read entire manual before assembling, installing, operating, or
servicing this equipment. Proper maintenance and inspection is
necessary for safe operation. DO NOT operate a damaged lift.

CL9 & CL10 Pad Adapter
Installation & Operation Supplement
- 2 - 01/31/2008
P1002-2002 IOM.doc
General Specifications
Figure 1

CL9 & CL10 Pad Adapter
Installation & Operation Supplement
- 3 - 01/31/2008
P1002-2002 IOM.doc
INSTALLATION
Drive On
Figure 2

CL9 & CL10 Pad Adapter
Installation & Operation Supplement
- 4 - 01/31/2008
P1002-2002 IOM.doc
1. The Pad Adapters are designed to be installed on the CL9 with a inside to
inside column dimension of 109”, and on a CL10 with a inside to inside
column dimension of 110”. See Figure 2.
Figure 3
2. Using supplied hardware, install the Pad Adapters as shown in Figure 3.
Note Pad Adapter orientation in Figure 2.
Figure 4
3. Adjust ¾” Bolt and Jam Nut so Pad Adapter is level. See Figure 4.

CL9 & CL10 Pad Adapter
Installation & Operation Supplement
- 5 - 01/31/2008
P1002-2002 IOM.doc
Figure 5
4. Locate the ¼” holes already in the column and tap 5/16-18 NC. If there
are accessories located at that location find a suitable working height and
using the Tire Hanger Bracket as a template drill two ¼” holes and tap
5/16-18 NC. See Figure 5.
5. The Tire Hanger Rod’s are installed into the sleeves on the Tire Hanger
Bracket and on the Pad Adapters, use supplied Cotter Pin during
installation.

CL9 & CL10 Pad Adapter
Installation & Operation Supplement
- 6 - 01/31/2008
P1002-2002 IOM.doc
PARTS BREAKDOWN CL9 & CL10

CL9 & CL10 Pad Adapter
Installation & Operation Supplement
- 7 - 01/31/2008
P1002-2002 IOM.doc
Item # Part # Qty./Lift Description
P1002-01 1 CL9 Pad Adapter Weld-Left
P1002-02 1 CL9 Pad Adapter Weld-Right
P2002-01 1 CL10 Pad Adapter Weld-Left (Shown)
1
P2002-02 1 CL10 Pad Adapter Weld-Right
2 P1002-03 2 Rubber Pad
3 427041 8 ¼-20 Self Tapping Screw
4 4100082 8 Washer, 13/32 x 13/16
5 10028 4 ¾-10 x 2 Hex Head Cap Screw, Gr. 5
6 10029 4 ¾-10 Jam Nut
7 10030 4 1 ¼”-7 x 6 ½” HHCS, Plated, Grade 5
8 10032 8 1 ¼” Flat Washer, Plated
9 10031 4 1 ¼”-7 Steel Lock Nut, Plated
10 10048 2 Capacity Decal (Not Shown)
11 TH-01 4 Tire Hanger Assembly
12 40126 4 Cotter Pin
P1002-06 2 CL9 Channel Weld-Front Tire Hanger
13 P2002-04 2 CL10 Channel Weld-Front Tire Hanger
14 10335 4 5/16-18 x 3/8” Phillips Pan HD Screw
15 31331 4 5/16” Split Lock Washer