Chamberlain MYQ-G0303-SP User manual

QUICK START GUIDE
MYQ-G0303-SP

To reduce the risk of SEVERE INJURY to persons:
• DO NOT enable the MyQ Home Bridge if operating either one-piece or swinging
doors. To be enabled ONLY on a sectional door.
Read instructions thoroughly BEFORE beginning.
If using this product with residential door openers, this product
must be used only with door openers manufactured after 1993 that
utilize photoelectric sensors. The photoelectric sensors are always
located on or near the bottom of the door track.
NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/
bystanders and device.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: This product can expose you to chemicals including lead, which are known to the State
of California to cause cancer or birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov

WHAT’S IN THE BOX

Yellow LED
Green LED
Blue LED
MyQ Home Bridge
Power Adapter
Mounting bracket
Warning Label
Hardware
(5/32" x 1-1/2"
screws)
BEFORE YOU START, YOU MUST HAVE A…

Router with
2.4GHz Wi-Fi®
Mobile device connected to
your home Wi-Fi network
Compatible device:
• Chamberlain®, LiftMaster®, and Raynor®garage door openers with MyQ®technology
• Craftsman®garage door openers with Smart Control or AssureLink™ Connectivity
• Chamberlain® and LiftMaster® MyQ Garage™
TIPS
• Keep any existing MyQ devices plugged in
• Do not delete existing devices from the MyQ app
• To control this HomeKit-enabled accessory, iOS 10.0 or later is recommended
• Watch set up videos atwww.chamberlain.com/MyQSupport
©2017 Sears Brands, LLC. All Rights Reserved. Craftsman and AssureLink are registered trademarks of KCD, IP, LLC.

Need Help?
Go to: www.chamberlain.com/MyQSupport
1. Check the Wi-Fi signal in the garage, where the MyQ Home Bridge will be mounted.
2. Make sure you have two or more Wi-Fi bars.
NOTE: If there are signal strength issues, please visit
https://www.chamberlain.com/wifisupportvideos for instructional videos.
3. Install the MyQ Home Bridge on the ceiling near the garage door opener, or in a
convenient location in the garage within Wi-Fi range.
TIP: Wrap excess power adapter cable around the mounting bracket.
4. Plug it in and make sure the green LED turns on solid.
5. Attach the warning label to the wall next to the door control.
CHAMBERLAIN MyQ®APP
INSTALL
1. Power the MyQ Home Bridge by plugging it in. The blue LED will
start blinking.
2. Download the Chamberlain MyQ®app or open the app if it is
already installed.
3. Create an account or sign-in.
4. Press “+” or “” icon and select MyQ-nnn under Discovered
Accessories/Devices.


Communication between iPhone, iPad, or iPod touch and the HomeKit-enabled MyQ®device is
secured by HomeKit technology and Security+ 2.0®.
Controlling this HomeKit-enabled accessory automatically and away from home requires anApple
TV with tvOS 10.0 or later or an iPad with iOS 10.0 or laterset up as a home hub.