Chamberlain 374UT User manual

To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:
• ALWAYSkeepremotecontrolsoutofreachofchildren.NEVERpermitchildrentooperate,orplaywithremotecontrol
transmitters.
• ActivategateordoorONLYwhenitcanbeseenclearly,isproperlyadjustedandtherearenoobstructionstodoortravel.
• ALWAYSkeepgateordoorinsightuntilcompletelyclosed.NEVERpermitanyonetocrosspathofmovinggateordoor.
Universal Mini Remote Control
Read instructions thoroughly BEFORE beginning.
If using the Universal Mini Remote Control with residential door openers, the remote control must be used only
with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are
always located on or near the bottom of the door track.
STOP
MODEL 374UT
TABLE OF CONTENTS
GETTING STARTED .................................................... 2
LOCATE THE PROGRAM/LEARN BUTTON ........................ 3-7
Chamberlain®products ............................................. 3
Genie®products ..................................................... 4
Linear®products..................................................... 5
Wayne Dalton®products ........................................... 5
LiftMaster®products ................................................ 6
Overhead Door®products .......................................... 6
Stanley®products ................................................... 7
GARAGE DOOR OPENERS .......................................... 8-9
Programming to a garage door opener with a
Program/LEARN button ............................................. 8
Programming to a Genie®Intellicode®2
garage door opener ................................................. 9
Programming to a LiftMaster garage door opener using
the LEARN button on the control panel ......................... 10
COMMERCIAL DOOR OPERATORS ................................. 11
Programming to a commercial door operator
with a RADIO button................................................ 11
GATE OPERATORS.................................................... 12
Program to a gate operator
with a Program/LEARN button.................................... 12
EXTERNAL RECEIVERS............................................... 13
Programming to an external receiver
with a Program/LEARN button.................................... 13
MYQ®LIGHT CONTROLS ............................................ 14
Programming to a MyQ®Light Control.......................... 14
NEED HELP? ........................................................... 15
BATTERY ............................................................... 16

2
GETTING STARTED
The Universal Mini Remote Control can be programmed to activate up to two products, such as a garage door opener, MyQ®light
control, gate operator, or commercial door operator. Each button on the remote control works independently of the other and must
be programmed separately. The images throughout this manual are for reference only and your product may look different.
Bottom Button
Garage Door Opener Commercial Door OperatorGate Operator
LED
You will need to locate the Program/LEARN button on your product before you start programming.
GARAGE DOOR OPENERS
TheProgram/LEARNbuttonistypicallylocatedonthebackorsidepanel
ofyourgaragedooropener.YourProgram/LEARNbuttonmayhavea
differentname(SMARTbutton,SETbutton,etc.).Forhelplocatingyour
Program/LEARNbuttonrefertotheTableofContentsinthismanualor
contactyourgaragedooropenermanufacturer.
COMMERCIAL DOOR OPERATORS
TheRADIObuttonistypicallylocatedonthelogicboardofyouroperator.
ForhelplocatingyourRADIObuttoncontactyourdooroperator
manufacturer.
GATE OPERATORS
TheProgram/LEARNbuttonistypicallylocatedonthecontrolboardof
youroperator.YourProgram/LEARNbuttonmayhaveadifferentname
(RADIObutton,XMITTERbutton,etc.).ForhelplocatingyourProgram/
LEARNbuttoncontactyourgateoperatormanufacturer.
EXTERNAL RECEIVER
Someproductsdonot
haveaProgram/LEARN
button.Inthiscase,the
Program/LEARNbutton
willbelocatedinan
externalreceiver.The
receiverwillbelocatedon
theproductormounted
nearby.Followthe
programminginstructions
foranexternalreceiver.

3
LOCATE THE PROGRAM/LEARN BUTTON
CHAMBERLAIN PRODUCTS

4
LOCATE THE PROGRAM/LEARN BUTTON
LearnCode
Button
ProgramSetButton
GENIE PRODUCTS

5
LOCATE THE PROGRAM/LEARN BUTTON
LINEAR PRODUCTS
Learn
Button
Learn
Button
ProgramSW
Button
WAYNE-DALTON PRODUCTS

6
Control Panel
LOCATE THE PROGRAM/LEARN BUTTON
LIFTMASTER PRODUCTS
OVERHEAD DOOR PRODUCTS
YellowLearn
Button
PurpleLearn
Button
OrangeLearn
Button
GreenLearn
Button
PresstheLEARN
buttontwice.
LearnCode
Button

7
LOCATE THE LEARN BUTTON
STANLEY PRODUCTS
LearnButton

8
GARAGE DOOR OPENERS
Programming to a Garage Door Opener with a Program/LEARN Button
The Program/LEARN button is typically located on the back or side panel of the garage door opener or an external receiver. For
help locating your Program/LEARN button contact your garage door opener manufacturer.
If you have a LiftMaster or Chamberlain branded garage door opener with a yellow learn button, press and release the learn
button, then press and hold the button on the remote control you would like to use. If programming is not successful, proceed
through the steps below.
If you have a Genie®Intellicode®2 garage door opener go to the next page.
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
BottomButton
1Startwithyourgaragedoorclosed. 2Pressandholdbottombuttonontheremotecontroluntil
theblueLEDstayssolid(approximately15seconds)then
releasethebutton.
3PressandreleasetheProgram/LEARNbuttononyour
garagedooropener.
4Ontheremotecontrol,pressandreleasethebuttonthat
youwouldliketoprogramtwice.TheblueLEDwillblink
forupto60seconds.
5 6
Waitforthegaragedoortomove,thenpressandrelease
eitherofthebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyou
programmedinstep4.Ifthegaragedooropenerdoesnot
activate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your garage door during
programming. Ensure garage door is clear of ALL obstructions.
LED

9
Programming to a Genie®Intellicode®2 Garage Door Opener
Before starting, you MUST have an existing Genie®Intellicode®2 remote control programmed to the garage door opener. For help
programming a Genie Intellicode 2 remote control, see your owner’s manual.
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
GARAGE DOOR OPENERS (continued)
1 2
34Onthegaragedooropener,pressandholdthe
Program/SetbuttonuntilboththelongandshortLED’s
lightupBLUE.
5
WaitfortheroundLEDonthegaragedooropenerto
flashBLUEthenpressandreleaseeitherofthebuttons
ontheremote.
6
PressandreleasetheProgram/Setbuttonandthelong
LEDwillflashPURPLE.
78
OntheGenie®remotecontrol,pressandreleasethe
buttonthatisalreadyprogrammedtothegaragedoor
opener.BothLED’swillflashPURPLE.
BottomButton
Startwithyourgaragedoorclosed. Pressandholdbottombuttonontheremotecontroluntil
theblueLEDstayssolid(approximately15seconds)then
releasethebutton.
Ontheremotecontrol,pressandreleasethebuttonthat
youwouldliketoprogram3times.TheblueLEDwillblink
forupto60seconds.
Thegaragedoorwillopen.
LED
Testtheremotecontrolbypressingthebuttonyou
programmedinstep7.Ifthegaragedooropenerdoesnot
activate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your garage door during
programming. Ensure door is clear of ALL obstructions.
LED

10
Programming to a LiftMaster Garage Door Opener Using the LEARN Button on the
Control Panel
IfyouhaveaLiftMasterorChamberlainbrandedcontrolpanel,pressandreleasetheLEARNbuttontwice,thenpressandholdthebuttonontheremotecontrolyou
wouldliketouse.Ifprogrammingisnotsuccessful,followthestepsbelow.
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
BottomButton
1Startwithyourgaragedoorclosed. 2Pressandholdbottombuttonontheremotecontroluntil
theblueLEDstayssolid(approximately15seconds)then
releasethebutton.
3PressthecontrolpanelLEARNbuttontwice,theredlearn
LEDwillturnon.
4Ontheremotecontrol,pressandreleasethebuttonthat
youwouldliketoprogramtwice.TheblueLEDwillblink
forupto60seconds.
5 6
Waitforthegaragedoortomove,thenpressandrelease
eitherofthebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyou
programmedinstep4.Ifthegaragedooropenerdoesnot
activate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your garage door during
programming. Ensure garage door is clear of ALL obstructions.
LED
GARAGE DOOR OPENERS (continued)

11
COMMERCIAL DOOR OPERATORS
Programming to a Commercial Door Operator with a RADIO Button
The RADIO button is typically located on the logic board of the operator or an external receiver. For help locating your RADIO
button contact your commercial door operator manufacturer.
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
RADIOButton
RADIOLED
RADIOButton
BottomButton
1Startwithyourcommercialdoorclosed. 2Pressandholdbottombuttonontheremotecontroluntil
theblueLEDstayssolid(approximately15seconds)then
releasethebutton.
3PressandreleasetheRADIObuttononyourcommercial
dooroperator.TheRADIOLEDwillilluminate.
WaittoseeiftheLEDontheoperatorflashesrapidly,
indicatingtheremotecontrolisprogrammedtothe
operator.PressandreleasetheRADIObuttononyour
commercialdooroperatortoexitprogrammingmode.
4Ontheremotecontrol,pressandreleasethebuttonthat
youwouldliketoprogramtwice.TheblueLEDwillblink
forupto60seconds.
5 6 Waitforcommercialdoortomove,thenpressandrelease
eitherbuttonontheremotecontroltoexitprogramming
mode.
LED
Testtheremotecontrolbypressingthebuttonyou
programmedinstep4.Ifthecommercialdooroperator
doesnotactivate,repeattheprogrammingsteps.
IMPORTANT: The remote will
activate your commercial door
during programming. Ensure
door is clear of ALL
obstructions.
7
LED

12
Programming to a Gate Operator with a Program/LEARN Button
The Program/LEARN button is typically located on the control board of the operator or an external receiver. For help locating your
Program/LEARN button contact your gate operator manufacturer.
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
GATE OPERATORS
PressandreleasetheProgram/LEARNbutton*onyour
gateoperator.TheProgram/LEARNLEDwillilluminate.
Program/LEARN
Button*
*Dependingonyourproduct,theProgram/LEARNbuttonmayhaveadifferent
name(usethebuttonforprogrammingremotecontrols).
BottomButton
1Startwithyourgateclosed. 2Pressandholdbottombuttonontheremotecontroluntil
theblueLEDstayssolid(approximately15seconds)then
releasethebutton.
34Ontheremotecontrol,pressandreleasethebuttonthat
youwouldliketoprogramtwice.TheblueLEDwillblink
forupto60seconds.
5 6
Waitforthegatetomoveortheprogram/LEARNLEDon
thegateoperatorblinks,thenpressandreleaseeitherof
thebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyou
programmedinstep4.Ifthegateoperatordoesnot
activate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your gate during
programming. Ensure gate is clear of ALL obstructions.
LED
Program/LEARN
LED

13
Programming to an External Receiver with a Program/LEARN Button
EXTERNAL RECEIVERS
PressandreleasetheProgram/LEARNbutton*onthe
externalreceiver.
Program/LEARN
Button*
If using the Universal Mini Remote Control with residential door openers, the remote control must be used only with
door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located
on or near the bottom of the door track.
The external receiver is typically located on the product or mounted near the product.
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
*Dependingonyourproduct,theProgram/SMART/LEARNbuttonmayhavea
differentname(usethebuttonforprogrammingremotecontrols).
STOP
BottomButton
1Startwithyourgaragedoor,commercialdoor,orgate
closed.
2Pressandholdbottombuttonontheremotecontroluntil
theblueLEDstayssolid(approximately15seconds)then
releasethebutton.
34Ontheremotecontrol,pressandreleasethebuttonthat
youwouldliketoprogramtwice.TheblueLEDwillblink
forupto60seconds.
5 6
Waitforthedoororgatetomove,thenpressandrelease
eitherofthebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyou
programmedinstep4.Ifthegaragedooropener,
commercialdooroperator,orgateoperatordoesnot
activate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your door or gate during
programming. Ensure door or gate is clear of ALL obstructions.
LED

14
MYQ®LIGHT CONTROLS
Programming to a MyQ®Light Control
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
PressandreleasetheLEARNbuttononthemodule(the
LEDonthemodulewilllight). Button
1Plugthelampintothemoduleandplugthemodule
intoanelectricaloutlet(theLEDonthemodulewill
flash).NOTE: Make sure the lamp is switched ON.
2IfthelampisnotON,pressandreleasethePowerbutton
onthemoduletoturnthelampON.
34Pressthebuttonontheremotecontrol.
5Thelamp’slightbulbwillblinkandtheLEDonthe
modulewillturnOFFwhenthedevicehasbeen
programmed.
LED

15
NEED HELP?
The remote control does not have good range.
• Therangeoftheremotecontrolmayvarydependingonvariousfactorsandenvironmentalfactors
The remote control will not program to a product with a Program/LEARN button.
• Checkthebatteryintheremotecontrol.TheLEDshouldlightwhenyoupressabutton.Replacethebatteryifnecessary.
The remote control LED will not light or it is dim.
• Replacethebattery.
The remote control LED does not activate the product until it is close to the product.
• Replacethebattery.

To prevent possible SERIOUS INJURY or DEATH:
• NEVERallowsmallchildrennearbatteries.
• Ifbatteryisswallowed,immediatelynotifydoctor.
Toreduceriskoffire,explosionorchemicalburn:
• ReplaceONLYwith3VCR2032coinbatteries.
• DONOTrecharge,disassemble,heatabove212°F(100°C)
orincinerate.
NOTICE:TocomplywithFCCandorIndustryCanada(IC)rules,adjustmentor
modificationsofthisreceiverand/ortransmitterareprohibited,exceptfor
changingthecodesettingorreplacingthebattery.THEREARENOOTHERUSER
SERVICEABLEPARTS.
TestedtoComplywithFCCStandardsFORHOMEOROFFICEUSE.Operation is
subjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
ChamberlainandLiftMasterareTrademarksofChamberlainGroup.GenieisaTrademarkofOverheadDoorCorporation.
OverheadDoorisaTrademarkofOverheadDoorCorporation.LinearisaTrademarkofLinearCorporation.MasterMechanic
isaTrademarkofTruServ.SearsisaTrademarkofSears&Roebuck.StanleyisaTrademarkofTheStanleyWorks.Wayne
DaltonisatrademarkofWayneDaltonCorporation.DoItisatrademarkofDoItBestCorporation.
©2016,LiftMaster
GDOPro103B AllRightsReserved
LiftMaster.com
1-800-442-1255
BATTERY
Disposeofbatteriesproperly.ReplaceONLYwith3VCR2032coin
batteries.
Need Help?
GotoLiftMaster.com/374ut
orcall1-800-442-1255
Battery
Screw