Champion Global Power Equipment 201189 User manual

OPERATOR'S MANUAL
MODEL #201189
600 PORTABLE POWER STATION
Champion Power Equipment, Inc., Santa Fe Springs, CA USA
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
4318-M-OP REV 20230920 EN
or visit championpowerequipment.com
READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to
do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.

201189 - 600 PORTABLE POWER STATION TABLE OF CONTENTS
2
TABLE OF CONTENTS
Introduction...................................................3
Safety Definitions ..........................................3
Important Safety Instructions.......................4
Lithium-ion Battery Safety........................................ 5
Safety and Dataplate Labels...................................... 8
Safety Symbols.................................................... 9
Operation Symbols............................................... 11
Controls and Features ................................. 12
Power Station .................................................... 12
Control Panel ..................................................... 13
Intelligauge ....................................................... 14
FCC Statement ................................................... 17
Industry Canada: ICES-003/NMB-003.......................... 17
Parts Included.................................................... 17
Parts Not Included ............................................... 17
Initial Use..................................................... 18
Unpacking ........................................................ 18
Grounding ........................................................ 18
Surge Protection ................................................. 18
Charging From Wall .............................................. 18
Using Included Easy Connect DC Solar Charge Harness ....... 19
Recommended Solar Panels..................................... 19
Using Car Charging Cable........................................20
Operation.....................................................20
Using the Power Station .........................................20
Using the Wireless Charging Pad................................ 20
Standby Mode ....................................................21
LED Light .........................................................21
Connecting Electrical Loads .....................................21
Resetting the Output .............................................22
Do Not Overload Power Station..................................22
Operation at High Altitude ....................................... 23
Turning Off the Power Station ...................................23
Moving the Power Station .......................................23
Maintenance................................................23
Cleaning the Power Station...................................... 23
Storage ...........................................................23
Specifications..............................................24
Power Station Specifications .................................... 24
Battery Specifications............................................ 24
AC Charger Specifications ....................................... 24
Solar Charging Specifications ................................... 24
Car Charging Specifications ..................................... 24
Temperature Specifications...................................... 24
Troubleshooting...........................................25
Power Station Fault Indicator Codes...........27
FOR PARTS BREAKDOWN
Search by model number at
championpowerequipment.com

201189 - 600 PORTABLE POWER STATION INTRODUCTION
3
SAFETY DEFINITIONS
The purpose of safety symbols is to attract your attention to
possible dangers. The safety symbols, and their explanations,
deserve your careful attention and understanding. The safety
warnings do not by themselves eliminate any danger. The
instructions or warnings they give are not substitutes for proper
accident prevention measures.
DANGER
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE
NOTICE indicates information considered important, but not
hazard-related (e.g., messages relating to property damage).
INTRODUCTION
Congratulations on your purchase of a Champion Power Equipment
(CPE) product. CPE designs, builds, and supports all of our
products to strict specifications and guidelines. With proper
product knowledge, safe use, and regular maintenance, this
product should bring years of satisfying service.
Every effort has been made to ensure the accuracy and
completeness of the information in this manual at the time of
publication, and we reserve the right to change, alter and/or
improve the product and this document at any time without prior
notice.
CPE highly values how our products are designed, manufactured,
operated, and serviced as well as providing safety to the operator
and those around the Power Station. Therefore, it is IMPORTANT
to review this product manual and other product materials
thoroughly and be fully aware and knowledgeable of the assembly,
operation, dangers and maintenance of the product before use.
Fully familiarize yourself, and make sure others who plan on
operating the product fully familiarize themselves too, with the
proper safety and operation procedures before each use. Please
always exercise common sense and always err on the side
of caution when operating the product to ensure no accident,
property damage, or injury occurs. We want you to continue to use
and be satisfied with your CPE product for years to come.
When contacting CPE about parts and/or service, you will need to
supply the complete model and serial numbers of your product.
Transcribe the information found on your product’s nameplate
label to the table below
CPE TECHNICAL SUPPORT TEAM
1-877-338-0999
MODEL NUMBER
201189
SERIAL NUMBER
DATE OF PURCHASE
PURCHASE LOCATION

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Cancer and Reproductive Harm – www.P65Warnings.ca.gov
WARNING
Read all safety warnings and instructions. Failure to follow
warnings and instruction may result in electric shock, fire
and/or cause serious personal injury. Save all warnings and
instruction.
DANGER
Power Station generates powerful voltage.
Keep your Power Station in a dry, well-ventilated area when in
use.
Do not operate the Power Station with a damaged cord, plug,
or a damaged output cable. Use only Champion electrical cords
for proper application.
Do not allow children or unqualified persons to operate or
service the Power Station.
Do not operate Power Station in wet conditions. To avoid short
circuits or electric shock do not allow unit to get wet. In the
event the unit does get wet, let the unit dry completely before
using.
Always use a ground fault circuit interrupter (GFCI) while
charging in damp areas and areas containing conductive
material such as metal decking.
Do not allow fluids to flow into Power Station. Corrosive or
conductive fluids, such as seawater, industrial chemicals,
bleach or bleach containing products can cause a short circuit,
damaging the Power Station and voiding the warranty.
This equipment has internal arcing or sparking parts which
should not be exposed to flammable vapors or liquids.
WARNING
To avoid fire or electrical shock hazard, observe all ratings on
the Power Station and accessory products you intend to use.
DANGER
This device is intended to be used indoors only. Do not use
outdoors.
WARNING
Do not use Power Station for medical life support uses.
In case of emergency, call 911 immediately.
NEVER use this product to power life support devices or life
support appliances.
Inform your electricity provider immediately if you or anyone
in your household depends on electrical medical equipment to
live.
Inform your electrical provider immediately if a loss of power
would cause you or anyone in your household to experience a
medical emergency.
WARNING
Power Station produces heat.
Do not touch hot surfaces.
Allow equipment to cool before touching.
WARNING
Exceeding the Power Station’s running capacity can damage
the Power Station and/or electrical devices connected to it.
DO NOT overload the Power Station.
DO NOT tamper or modify the Power Station in any way.
WARNING
Improper treatment or use of the Power Station can damage it,
shorten its life and void the warranty.
Use the Power Station only for intended uses.
DO NOT expose Power Station to moisture, dust, or dirt.
DO NOT allow any material to block the cooling slots.
If connected devices overheat, turn them off and disconnect
them from the Power Station.
DO NOT use the Power Station if:
–Electrical output is lost
–Equipment sparks, smokes or emits flames
–Equipment vibrates excessively

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
5
Lithium-ion Battery Safety
DANGER
Electrolyte inside the battery is harmful to skin and eyes.
Electrolyte may pose an increased risk of harm if not handled
properly.
Under abusive conditions, liquid may be ejected from the
battery; avoid contact. Liquid ejected from the battery may
cause irritation or burns. If contact accidentally occurs, flush
with water. If the battery leaks and electrolyte gets in your
eyes, do not rub them, immediately flood eye with running cold
water for at least 10 minutes and seek medical help. If left
untreated, electrolyte can cause permanent eye injury. Keep
away from children.
DANGER
This Power Station generates the same potential lethal AC
electrical voltage as a standard building wall outlet.
Always treat the Power Station as you would a normal AC
outlet on a standard building wall.
WARNING
When using the Power Station:
–Always use in a dry well ventilated area while in use and
do not obstruct fan openings on unit. Inadequate ventilation
may cause execessive heat and damage the unit.
–Always keep the unit clean and dry and inspect for dirt,
dust, or moisture prior to every use.
–Power cord plugs must always match the outlet. Never
modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
–Connect only to properly grounded outlets.
–To reduce risk of damage to the electric plug and cord,
pull the plug rather than the cord when disconnecting the
Power Station. Never use the cord for carrying, pulling or
unplugging the tool.
–Do not use this Power Station if the power cord or the
battery cables are damaged in any way.
–Always use a suitable extension cord to reduce the risk of
electric shock.
–Always keep the cord away from heat, oil, sharp edges or
moving parts.
–Always position cords carefully to avoid hazardous
conditions. Tripping or snagging on cords can cause
injury or cause product damage. Never allow cords to run
through puddles or across wet ground.
–Use of an accessory attachment not recommended or sold
by Champion Power Equipment may result in a risk of fire,
electric shock, or injury to persons.
–To reduce the risk of electric shock always unplug the
cord from outlet when not in use and before servicing or
cleaning.
–Do not insert foreign objects into outputs or ventilation
holes.

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
6
WARNING
–Do not overload the Power Station’s capacity. Exceeding
the wattage/amperage capacity may damage the power
supply and/or electrical devices connected to it. Inductive
loads such as refrigerators with compressors, motor
powered equipment, and air conditioners may have much
greater starting wattage than their rated wattage.
–Do not connect Power Station output to a building’s
electrical system.
–Do not use this unit if you do not understand these
operating instructions.
–Maintain the labels and nameplates on this Power Station.
These carry important information.
WARNING
–Do not use a Power Station or appliance that is damaged
or modified. Damaged or modified internal batteries may
exhibit unpredictable behavior resulting in fire, explosion or
risk of injury.
–Do not remove cover. No user serviceable parts inside.
–Do not tamper or disassemble the Power Station to attempt
service or replace the battery. Incorrect reassembly may
result in a risk of fire, electric shock or personal injury.
–For service information please contact our Champion
Technical Support Team at 1-877-338-0999. Please have
your serial number and model number available when
service, repair or replacement is required.
–Never place fingers or hands inside the product.
WARNING
–To reduce the risk of injury or damage, avoid contact with
any hot surface.
–Do not use the Power Station near sources of high heat or
fire. Exposure to fire or temperature above 265°F (130°C)
may cause explosion.
–Do not discharge the Power Station battery in
temperatures below 5°F (-15°C) or above 104°F (40°C).
–Do not allow fluids to flow into the Power Station. Corrosive
or conductive fluids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc.,
can cause a short circuit.
–Follow all charging instructions and do not charge the
Power Station outside the temperature range specified in
the instructions. Charging improperly or at temperatures
outside the specified range may damage the battery and
increase the risk of fire.
When charging the Power Station:
–Always charge the Power Station’s internal battery in a
well-ventilated area.
–Do not use the AC charging cable outdoors.
–Do not expose AC charging cable to oil, oil vapor, grease,
gasoline, gasoline vapors or other caustic substances that may
damage the AC charging cable.
–Do not charge the Power Station below 43°F (6°C) or above
104°F (40°C).
–Do not charge Power Station in rain, snow, damp or wet
locations.
–Do not overcharge the Power Station. Use only supplied AC
charging cable and follow solar charging guidelines and
voltage and current limits.
–Always connect to properly grounded outlets.
–Never use Power Station or charger in the presence of
explosive atmospheres (gaseous fumes, dust or flammable
materials).
–Never leave the Power Station unattended while charging.
If the internal battery smokes, or gives off an odor during
charging, terminate charging immediately.
–During charging, if the Power Station battery becomes hot to
the touch, stop charging. Allow Power Station to cool before
resuming.
–Always unplug charger when not in use.
–To reduce the risk of electric shock, always unplug charger
before cleaning or maintenance. Do not allow water to flow
into plug. Use a Ground Fault Circuit Interrupter (GFCI) to
reduce shock hazards.
Grounding Information:
If the Power Station should malfunction or breakdown, provides
a path of least resistance for electric current to reduce the risk
of electric shock. This product is equipped with a cord having an
equipment conductor and a plug. The plug must be plugged into
an outlet that is properly installed and grounded in accordance
with all local codes ordinances. We strongly recommend that you
consult with a qualified electrician to ensure compliance with local
electrical codes.
When storing the Power Station:
–This Power Station is intended to be stored indoors and shall
not be stored or left outdoors when not in use.
–Do not stack any items on top of the Power Station during
storage.
–Store your Power Station in a cool, dry place between 32°F
(0°C) and 104°F (40°C). The ideal storage temperature is 59°F
(15°C).

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
7
–Do not store Power Station where temperatures may exceed
104°F (40°C) such as in direct sunlight, in a vehicle or metal
buildings especially during the summer.
–Do not store the Power Station near sources of high heat or
fire.
–Do not store the Power Station when battery level is at 20% or
less state of charge (SOC). The ideal storage SOC is 40-60%.
–When storing the Power Station for periods of one month or
longer, store the Power Station at an SOC of about 60%. Every
three months, discharge the Power Station to 0% and recharge
back to 100%, then discharge it to 60%.
–Lithium batteries must be charged regularly to perform well.
The Power Station must be fully charged by you at least once
every 6 months (180 days).
In case of battery damage:
–If damaged, the internal battery may emit hazardous fumes.
If fumes are present, move Power Station to a well-ventilated
area.
–Do not try to repair the Power Station or replace the battery.
Safe disposal of Lithium-ion battery:
–Lithium-ion batteries contain elements that pose health risks
to individuals if they are allowed to leach into the ground
water supply. In many states and counties, it may be illegal to
dispose of these batteries in standard household waste.
–To dispose the battery safely, apply tape over any exposed
connectors to prevent accidental shorting of the positive and
negative terminals of the battery during transport.
–Place the battery in a clear sturdy plastic bag, seal the bag and
deposit the battery into the recycling container at your local
municipal hazardous waste (HHW) recycling location.
–In the United States and Canada, a large network of over
30,000 battery drop-off locations may be found at
www.call2recycle.org.
–Never dispose of the battery in a fire or incinerator, as the
battery may catch fire and explode.

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
8
Safety and Dataplate Labels
These labels warn you of potential hazards that can cause serious injury. Read them carefully.
If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement.
LABEL DESCRIPTION
A
4299-L-SF-B
 DANGER
 DANGER
 CAUTION  MISE EN GARDE
 WARNING  AVERTISSEMENT
Do not overcharge the internal b attery. To reduce the risk of injury, user must r ead Operator’s Manua l. Do not smoke, strike a match, or cause a
spark in the v icinity of the power pac k. Only charge the in ternal batter y in a well ventilated area . Risk of Explosion. This equipment has a rcing or
sparking p arts which should not be exposed to flammable vapors. Risk of Electric Shock and R isk of Fire. This device is not to be stored in a
vehicle. / Ne pas surcharger la batterie interne. Pour déduire le risque de bles sure, l’utilisateu r doit lire le manuel de l’opé rateur. Il ne fa ut pas
fumer, allumer une allumette ou prod uire des étincelles à p roximité du bloc d'alime ntation. Charg er la batterie uniq uement dans un endro it bien
aéré. Risque d'explosion. Cet équipement comporte des pièces susceptibles de produire des arcs ou des étincelles qui ne doivent pas êt re
exposées à de s vapeurs inflammables. Risques de décharge électrique et d'incendie. Le dispositif ne doit pas être rangé dans un véhicule.
This device is intended to be used i ndoors only. Do not use o utdoors.
Cet appar eil est destiné à être utilisé à l'intérieur uniquement. Ne pas utiliser à l'extérieur.
Risk of Elec tric Shock. Do not rem ove cover. No user serviceable parts insi de. Refer servicing to qualified serv ice personnel. Connect only to
properly grounded outlet s. Risk of Injury To Persons. Do not use this pro duct if the power cord or t he battery cab les are damaged in any way. Th is
device is not intended for use in a commercial repair fac ility. This device is in tended to be stored indoors when not in use.
Risque de décharge électrique. Ne pas enlever le couvercle. Aucune des piè ces à l'intérieur ne peu t être réparée par l'utilisateur. L'entretien
courant doit être effectué par un personnel d'entretien qualifié. Bra ncher l'unité uniquement à des prises de courant correctement mises à la
masse. Risque de blessure aux personnes. Ne pas u tiliser ce produit si le cordon d'alimenta tion ou les câbles de bat terie sont endommagé s de
quelque façon. Le dispositif n'est pas destiné à êtr e utilisé dans un ateli er de réparation commercial. Le dispos itif est destiné à être rangé à
l'intérieu r lorsqu'il n'est pas ut ilisé. Le dispositif ne doit pas être rangé ou laissé à l'extérieu r lorsqu'il n'est pas ut ilisé.
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y Daño Reproductivo – www.P65Warnings.ca.gov
AVERTISSEMENT : Cancer et Troubles de l'appareil reproducteur – www.P65Warnings.ca.gov
K485 152 109 ---
ColorsAPN 4299-L-SF
Rev B
Size 158 x 130 mm
Artwork Notes
3mm corner radius; 2mm safe margin; to be printed
on
white substrate.
Revision Changes
rev B: xed misspelling
This art work belongs to Champi on Power Equipment. Th e contents are confi dential and privileg ed and shall not be disclo sed to or used by or for
outside par ties without th e explicit consent o f Champion Power Equi pment.
Safety Symbols/ Safety
Warning
B
Model / Modèle: 201189
Capacity / Capacité : 579Wh 22.2V 26.1Ah
USB Output / Sortie USB : USB-A (x3) 5V 2.4A, 12W max
USB-A QC3.0 : 5V 3A, 9V 2A, 12V 1.5A, 18W max
USB-C PD3.0 : (5V,9V,12V,15V)/3A; 20V/3.25A, 65W
12VDC Automotive / 12VCC Automobile : 12V 10A, 120W
DC Input: / Entrée CC : 12V-30V, 8A (max)
Wireless Charging / Chargement sans fil : 5V 1A, 7.5V 1A,
9V 1.12A, 10W max
Discharging temperature / Température de décharge :
5°F-104°F (-15°C-40°C)
Charging temperature / Température de charge :
43°F-104°F (6°C-40°C)
DC output / Sortie CC : 249W
AC output / Sortie CA : 600W 120VAC 60Hz,
1200W Starting / Démarrage
CHAMPION POWER EQUIPMENT, INC. 12039 SMITH AVENUE, SANTA FE SPRINGS, CA 90670 USA / É.-U.
1-877-338-0999 • WWW.CHAMPIONPOWEREQUIPMENT.COM • MADE IN CHINA / FABRIQUÉ EN CHINE
CAN ICES-003/
NMB-003
4288-L-PR-A
Conforms to
ANSI/CAN/UL
STD.2743
Conforme à
ANSI/CAN/UL
STD.2743
Contains IC :
10186A-CPEWC01
Contiene IC :
10186A-CPEWC01
Contient IC :
10186A-CPEWC01
5022215
K--- --- --- ---
ColorsAPN 4288-L-PR
Rev A
Size 84.5 x 44.5 mm
Artwork Notes
3mm corner radius; 2mm safe margin; to be printed
on
white substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
Power Station Dataplate
C
MODEL / MODÈLE : SOY-2520800-244-B INPUT / ENTRÉE : 100-240V 60/50HZ, 3.0A
OUTPUT / SORTIE : 25.2V 8.0A, 201.6W
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Ces dispositifs se conforment à la section 15 du règlement de la FCC. Le
fonctionnement est assujetti aux conditions suivantes : (1) Ce dispositif ne doit pas
générer d’interférences nuisibles, et (2) ce dispositif doit accepter toute interférence
qui peut causer un fonctionnement non désiré.
ICES-003(B)/NMB-003(B)
Shenzhen SOY Technology Co., Ltd
4F,5F 501, A building, No. 11,
Dakan Industrial, 2nd Road, xili Town,
Nanshan District, Shenzhen City, China
Made in China / Fabriqué en Chine
4289-L-PR-A
Certified to UL/CSA STD.
C22.2 NO. 62368-1
Certifié selon la norme
UL/CSA C22.2 NO. 62368-1
4004541
SWITCHING ADAPTER / ADAPTATEUR DE COMMUTATION
XXXXXXXXXXXX
K--- --- --- ---
ColorsAPN 4289-L-PR
Rev A
Size 119.2 x 41.7 mm
Artwork Notes
3mm corner radius; 2mm safe margin; to be printed
on
WHITE substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
Charging Adapter
Dataplate
Bottom Bottom of Adapter
A
B
Back
C

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
9
Safety Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these
symbols will allow you to more safely operate the product.
SYMBOL MEANING
Read Operator’s Manual. To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Eye protection. Always wear eye protection with side shields marked to comply with ANSI Z87.1.
Ground. Consult with local electrician to determine grounding requirements before operation.
Electric Shock. Failure to use in dry conditions and to observe safe practices can result in
electric shock.
Shield eyes. Explosive gases can cause blindness or injury.
If damaged, battery may emit hazardous fumes. If fumes present, move battery to a well-ventilated area.
Fire/Explosion. Batteries and its vapors are extremely flammable and explosive. Fire or explosion
can cause severe burns or death. Keep Power Station at least 5 feet (1.5m) from all objects to prevent
combustion.
Blindness or severe burns. Electrolyte solution can cause blindness or severe burns.
Open Flame Alert. Keep away from fuel, smoking, open flames, sparks, pilot lights, heat, and other
ignition sources.

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
10
SYMBOL MEANING
Wet Conditions Alert. Do not operate Power Station in wet conditions.
This product uses lithium-ion (Li-ion) batteries. Local, state, or federal laws prohibit disposal of
Li-ion batteries in ordinary trash. In the United States and Canada, a large network of over 30,000
battery drop-off locations may be found at www.call2recycle.org and/or consult your local waste
authority for information regarding available recycling disposal options.

201189 - 600 PORTABLE POWER STATION IMPORTANT SAFETY INSTRUCTIONS
11
Operation Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these
symbols will allow you to more safely operate the product.
SYMBOL MEANING
Hold for 3 seconds to power ON/OFF
Wireless Charging Pad
USB Output Button
AC Output Button
DC Output Button
Charging Input Port
SYMBOL MEANING
USB Fast Charge Port
USB-C PD Port
3
Qualcomm Quick Charge 3+
Pure Sine Wave Output
LED Light Button

201189 - 600 PORTABLE POWER STATION CONTROLS AND FEATURES
12
CONTROLS AND FEATURES
Read this operator’s manual before operating your Power Station. Familiarize yourself with the location and function of the controls and
features. Save this manual for future reference.
Power Station
1. Carrying Handle –Used to lift or carry the unit.
2. Wireless Charging Pad (5V 1A, 7.5V 1A, 9V 1.12A,
10W max.)– Used to charge compatible devices when placed
in center of pad and USB ports turned ON.
3. Control Panel –See Control Panel section.
4. Cooling Vents – Used to cool battery and other internal
components. Do not block.
5. Charging Port - 12-30V DC, max. 8A/200W – Used to
charge the power station via supplied accessories.
1
3
5
4
2

201189 - 600 PORTABLE POWER STATION CONTROLS AND FEATURES
13
Control Panel
1. On/Off Button – Turns the Power Station ON/OFF when
pressed for three seconds.
2. 12V DC Button – Turns the 12V DC port ON/OFF when
pressed one time.
3. LED Light Button – Used to turn the LED light ON/OFF and
toggle through different modes.
4. LED Light – Used to illuminate the work area in front of the
Power Station.
5. Intelligauge – See Intelligauge section.
6. USB Button – Turns the USB ports ON/OFF when pressed
one time.
7. AC Button – Turns the AC outlet ON/OFF when pressed one
time.
RECEPTACLES
Az
12V DC/10A, 120W.
(12V DC Regulated Automotive)
May be used to supply electrical power for
operation of 12 Volt DC, 10 Amp electrical loads.
B
(5V, 9V, 12V, 15V)/3A; 20V/3.25A, 65W max.
(USB-C PD3.0)
Port may be used to supply DC power to
cellphones, laptops, tablets, and similar devices
up to a maximum of 65W with PD 3.0 compatible
devices.
C
5V/3A, 9V/2A, 12V/1.5A, 18W max.
(USB-A QC3.0)
Port may be used to supply DC power to
cellphones, laptops, tablets, and similar devices
up to a maximum of 18W with Quick Charge
3.0(QC 3.0) compatible devices.
D
(3x) 5V/2.4A, 12W max. (USB-A)
Ports may be used to supply DC power to
cellphones, laptops, tablets, and similar devices
up to a maximum of 12W.
E
(2x) 120V AC, 5.0A (NEMA 5-15R)
May be used to supply electrical power for
operation of 120 Volt AC, 5.0 Amp, single phase,
60 Hz electrical loads.
1
5
2
4
3 6
7
C
B
A
E
D

201189 - 600 PORTABLE POWER STATION CONTROLS AND FEATURES
14
Intelligauge
1. Charging/Discharging – Shows “Charging” when input
watts are higher than output watts. Shows “Discharging”
when output watts are higher than input watts.
2. Hour Meter – Shows time, in hours, until battery level is 0%
(when “Discharging” shown) or hours until 100% charged
(when “Charging” shown).
3. Communication Fault – Indicates a communication fault
between the Battery Management System (BMS) or other
component.
4. Error – Indicates a fault and may be accompanied by a Fault
Indicator Code (see #14. Fault Indicator Code).
5. Overload – Indicates the devices’ power demands exceed
the max wattage of the ports/outlets.
6. Battery Percentage (%) – Shows battery level in percent.
7. Low Temperature – Indicates internal temperature too low.
8. High Temperature – Indicates internal temperature too high.
9. Battery Fault – Indicates a battery fault and may be
accompanied by a Fault Indicator Code (see #14. Fault
Indicator Code).
3
2
4 5 67 8 9 10
1516 14 13
11
10. Cooling Fan – Indicates the fan is on to cool internal
components. Intermittent operation of the fan is normal.
11. Power Meter – Shows power, in watts, supplied to load
(when “OUTPUT” shown) or supplied to charge the Power
Station (when “INPUT” shown).
12. INPUT/OUTPUT – Toggles automatically to show input and
output watts.
13. Frequency – Shows the frequency, in Hertz (Hz), of the AC
outlet load.
14. Fault Indicator Code – Shows error code. See
Troubleshooting section POWER STATION FAULT INDICATOR
CODES.
15. DC Input – Indicates the power station is being charged.
Even when charging through wall outlet, DC Input icon is
illuminated as the AC power is being converted to DC to
charge the battery.
16. Fuel Gauge – Shows battery level in 20% increments.
This meter displays a variety of info such as input/output power, charge/discharge times, as well as faults, errors, and protection codes to
help diagnose malfunctions in the Power Station.
1
12

201189 - 600 PORTABLE POWER STATION CONTROLS AND FEATURES
15
Display Modes and Indicators
See Power Station Fault Indicator Codes section for full list of codes.
MODE DESCRIPTION
Charging Example: 0.9 Hours to charge to full, 199 watts in,
battery is at 56%, Fan is ON.
Discharging (AC) Example: 0.5 Hours to empty, 600 watts out, battery
is at 57%, Fan is ON.
Discharging (DC) Example: 19.1 Hours to empty, 12 watts out, battery
is at 57%.
AC Voltage Protection
(Low Battery)
Example: E85 Error code displayed. AC Output cutoff
when battery falls to 5%. Fault will clear when
charged to 7%.
High Temperature
Warning (E77)
Example: The battery surface temperature ≥60 ° C,
reduce AC load, move to cooler or shaded location.

201189 - 600 PORTABLE POWER STATION CONTROLS AND FEATURES
16
MODE DESCRIPTION
High Temperature
Protection (E78)
Example: The battery surface temperature ≥64 ° C,
the AC and 12V DC will be closed automatically, the
USB & PD port goes on working. Move the power
station to cooler or shaded location.
Low Temperature
Warning
Example: Illuminated when the Power Station has
experienced a low temperature event.
Low Voltage
Protection Alarm
(E11)
Example: Battery fully discharged, power station
needs to be recharged immediately.
Overload Example: Rated output exceeded. Reduce output,
press the USB, 12V DC, or AC button to reset output.

201189 - 600 PORTABLE POWER STATION CONTROLS AND FEATURES
17
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1a. This device may not cause harmful interference.
1b. This device must accept any interference received,
including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
NOTICE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and
receiver.
–Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult dealer or an experienced radio/TV technician for help.
Industry Canada: ICES-003/NMB-003
This device complies with Industry Canada license - exempt RSS
standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
Parts Included
Accessories
Easy Connect DC Solar Charge Harness ..........................1
Car Charging Cable ................................................1
AC Charging Adapter...............................................1
AC Charge Cable ...................................................1
Parts Not Included
–Solar Panels

201189 - 600 PORTABLE POWER STATION INITIAL USE
18
INITIAL USE
Your Power Station must be charged before first use.
If you have any questions regarding the use of your Power Station,
call our Technical Support Team at 1-877-338-0999. Please have
your serial number and model number available.
Unpacking
1. Set the shipping carton on a solid, flat surface.
2. Remove everything from the carton except the Power Station.
3. Using the carrying handle of the unit, carefully remove the
Power Station from the box.
Grounding
Your Power Station must be properly connected to an appropriate
ground to help prevent electric shock.
If the Power Station should malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce
the risk of electric shock. This product is equipped with a cord
having an equipment grounding conductor and a grounding plug.
The plug must be plugged into an outlet that is properly installed
and grounded in accordance with all local codes ordinances. We
strongly recommend that you consult with a qualified electrician to
ensure compliance with local electrical codes.
Surge Protection
Electronic devices, including computers and many programmable
appliances use components that are designed to operate within a
narrow voltage range and may be affected by momentary voltage
fluctuations. While there is no way to prevent voltage fluctuations,
you can take steps to protect sensitive electronic equipment.
–Install UL1449, CSA-listed, plug-in surge suppressors on the
outlets feeding your sensitive equipment.
Surge suppressors come in single- or multi-outlet styles.
They’re designed to protect against virtually all short-duration
voltage fluctuations.
Charging From Wall
NOTICE
The Power Station must be fully charged at least every 180
days when in storage, to keep the internal battery in good
operating condition. Do not store the Power Station when
battery level is at 20% or less state of charge (SOC). The ideal
storage SOC is 40-60%.
1. Open the input port cover.
2. Plug the AC Charging Adapter Cable into the input port.
3. Plug the other end into a standard wall outlet. Ensure the
cable is securely connected to the adapter.

201189 - 600 PORTABLE POWER STATION INITIAL USE
19
Using Included Easy Connect DC Solar
Charge Harness
NOTICE
The Power Station’s charging wattage is rated at 200W.
However, depending on environmental conditions and solar
panel efficiency, it may be necessary to use a solar panel rated
higher than 200W to reach the full 200W of charging power.
It will not damage the Power Station to use solar panels rated
more than 200W as long as they are rated between 12-30V.
The charging power and rate is reduced as the battery level
gets closer to 100% to safely charge the internal battery.
It is important to adjust your solar panels to face the sun as
best as possible throughout the day to achieve maximum
charging efficiency.
For example, on a cloudy day, a 300W or higher solar panel
may be needed to produce 200W of charge. Ensure the solar
panel is within the power station’s required voltage and current
range.
1. Open the input port cover.
2. Plug the EZ connect solar charging cable into the input port.
3. Connect solar panel using MC4 connectors.
4. It is important to adjust your solar panels to face the sun as
best as possible throughout the day to achieve maximum
charging efficiency.
Recommended Solar Panels
NOTICE
It will not damage the Power Station to use solar panels rated
more than 200W as long as they are rated between 12-30V.
Do not exceed voltage or current rating. Connecting solar
panels in series will add their voltages and connecting solar
panels in series will add their current together.
Model Watts Connector Type
Renogy RNG-100D-SS 100 MC4
Renogy Solar Panel 200
Watt 12 Volt 200 MC4
Bluetti SP120 120 MC4
Bluetti SP200 200 MC4
ECOFLOW EFSOLAR
160W 160 MC4
Champion 201246 120 MC4
Champion 201247 200 MC4
Any solar panel rated between 12-30V, 8A with MC4 connectors
can be used. The Power Station has a built in MPPT solar charge
controller and inverter so there is no need to buy an external
charge controller, inverter, or worry about connecting more than
200W of solar panels to reach 200W of input on cloudy days.

201189 - 600 PORTABLE POWER STATION OPERATION
20
Using Car Charging Cable
1. Open the Input Cover.
2. Plug the car charging cable into the input port.
3. Connect the other end into a regulated 12V outlet.
OPERATION
Using the Power Station
1. Press and hold the power button for three seconds, until
display illuminates.
2. Press the appropriate button to turn on power for ports/
outputs intended to be used.
NOTICE
See Specifications section for maximum allowable watts. The
sum of the watts of the 12V DC outlet, wireless charging pad,
and USB ports can not exceed the number listed next to “DC
Watts”. The 120V AC outlet(s) can not exceed the number
listed next to “AC Running Watts” and “AC Starting Watts”.
All ports and outlets may be used simultaneously and each
have their own wattage limits and protections.
NOTICE
To protect sensitive electronics, as the Power Station’s battery
level drops to 5%, the AC output will be shutoff and fault
indicator code E85 will be shown. DC and 12VDC ports can
still be used. AC output will be restored once the power station
is recharged.
3. Plug in desired devices.
Using the Wireless Charging Pad
1. Press the USB button.
2. Place the device in the center of the charging pad. If the
device is not centered on the pad, the device may not charge
or charge slowly.
NOTICE
Ensure your device is compatible with wireless charging.
Remove phone case for more efficient charging.