Champion Power Equipment C42412-1 User manual

Congratulations on your purchase of a Champion Power Equipment generator. CPE designs and builds generators to
strict specifications and with proper use and maintenance this generator should bring you years of satisfying service.
Read, study, and follow all instructions before operating this device. Failure to heed these instructions may
result in personal injury and/or property damage.
WARNING
Your generator can develop tremendous power forces and if used unsafely or improperly could result in property damage, serious
injury, or death. Throughout this manual you will find the following symbols for caution, warning, and danger. Pay particular attention to
the notes preceded by these symbols as they are written for your safety. Ultimately, safe operation of this device rests with you, the
operator.
Indicates a hazard which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
equipment damage. This notation is also used to alert against unsafe practices.
CAUTION
SAFETY PRECAUTIONS
SAFETY AND OPERATION INSTRUCTIONS
Failure to follow these instructions and warnings may result in death, personal injury, or property damage.
WARNING
DANGER Gasoline engines produce toxic carbon monoxide exhaust fumes. Breathing exhaust fumes will cause serious injury
or death.
WARNING No modifications, alterations, or deviation to the generator are authorized by the manufacturer and should not be made.
Read, study, and understand the operator's manual prior to operation of this product. Read, study and understand the
engine manual prior to operation. Follow all warnings and instructions.
Know your equipment. Check the applications, limitations, and potential hazards with this unit and its placement or
location.
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or
other reproductive harm.
Gasoline is flammable. Check for spilled fuel or fuel leaks. Stop engine and allow to cool at least 2 minutes before
refueling.
Equipment must be used on a hard, level surface, free from grease, fuel and other combustible materials.
Engine must not be run at excessive speeds. Operating an engine at excessive speeds increases the hazard of personal
injury. Do not tamper with the parts which may increase or decrease the speed of the engine.
Do not operate this generator in the rain or unusually wet conditions.
This generator is designed for outdoor use only; do not use this generator inside any building or enclosure including the
generator compartment of a recreational vehicle (RV). Fire or an explosion may result.
No user-performed modifications, including venting of exhaust and/or cooling ventilation are authorized by the
manufacturer, Also, allow at least two feet of clearance on all sides of the generator even while operating the unit
outdoors.
If this unit is used for backup power in the event of a utility power failure, the following step must be taken: Before
connecting the generator to an electrical system, open the main circuit breaker or main switch serving the system, to
isolate the generator system from the electric utility. Failure to isolate the generator and utility systems may result in
damage to the generator and may also result in injury or death to electric utility workers, due to a back feed of electrical
energy.
This product is equipped with a spark-arresting muffler. If the product will be used around flammable materials, or on land
covered with materials such as agricultural crops, forest, brush, grass, or other similar items, then the approved spark
arrester must be installed. SPARK-ARRESTERS ARE REQUIRED IN THE STATE OF CALIFORNIA. Spark arresters are
also required on some U.S. Forest Service land and may also be legally required under other statutes and ordinances.
Never step over a generator.
Failure to heed these warnings may result in personal injury and/or property damage. No modifications, alterations, or
deviations to the generator are authorized by the manufacturer and should not be made.
Engine speed has been factory set to provide safe operation. Tampering with the engine speed adjustment could result in
overheating of attachments and could cause a fire. Never attempt to “speed up” the engine to obtain more performance.
Both the output voltage and frequency will be thrown out of standard by this practice, endangering attachments and the
user.
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
DANGER
WARNING
1

2
CAUTION This generator has been shipped from the factory without oil in the crankcase. Operating the unit without oil can ruin the
engine.
You MUST unplug any load from the generator before starting. This will help to prevent permanent damage to any
appliances.
Do not exceed rated capacity of current draw. Current load must be kept within rating on the generator label. Overloading
will damage the unit and/or shorten its life.
For starting, grasp the starter grip and pull slowly until you feel resistance. Then pull firmly. Repeat if necessary with
choke opened slightly. When engine starts, open the choke gradually until the engine is warm.
CAUTION
CAUTION
CAUTION
INCLUDED WITH YOUR GENERATOR
1. Generator
2. Battery Cable
3. Bolts
4. Rubber Mounts
5. Spark Plug Tool
1
1
4
4
1
CONTROL PANEL COMPONENTS
1. Engine Switch - Use this switch to turn power on.
2. AC Voltmeter - Use the voltmeter as a visual aid. It indicates the AC voltage. The normal voltage meter reading is 110 to 120 volts.
Excessive meter voltage could result in damage to appliances.
CAUTION Engine speed has been adjusted at the factory and establishes the proper electrical frequency output (60 Hz). Do not
attempt to increase the speed of the engine for higher output. Serious damage could occur to the generator, engine or
electrical appliance.
3. AC Socket (120 V) - This outlet is protected by a 10 Amp, push-to-reset circuit breaker. This receptacle powers 120 Volt AC, 60 Hz, Single
Phase loads requiring up to 10 AMPS or 1200 Watts of power.
WARNING Combined amperage of the receptacle is not to exceed circuit breaker limits.
4. 12 VOLT, 10 Amp DC Outlet - This receptacle allows you to recharge a 12 Volt automotive or utility style storage battery with the battery
charge cables provided. This receptacle can not charge 6 Volt batteries and can not be used to crank an engine. It is also not recommended
for charging deep cycle batteries. Do not charge any batteries for extended periods without checking.
Never refuel a generator while it is in operation. Make sure the generator is not running. (This is a severe risk of
fire.)
WARNING
WARNING Engine Exhaust, some of it’s constituents, and certain vehicle components contain or emit chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.”
This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling .”

3
CAUTION Let the engine stabilize and warm up for about five minutes after starting and before using.
DO NOT OVERLOAD THE GENERATOR. Add up the rated watts (or amps) of all loads to be connected at one time.
This total should not be greater than the rated wattage/amperage capacity of the generator.
CAUTION
STARTING WATTAGE REQUIREMENTS
1. Some appli
convert voltage and amperage to wattage:
a. FORMULA: VOLTS X AMPS = WATTS
b. EXAMPLE(Voltage and amperage for 1/3 HP furnace fan):
120 Volts X 10 Amps = 1200 Running Watts
2. To deter
that was calculated by 3 times to assure adequate generator capacity. If the nameplate information is not available, use the values on the
following page as a guide.
3. Remem atts to
start.) Most resistive loads will be listed in wattage.
4.Use the chart on the next page as a reference guide.

RUNNING WATTAGE GUIDE
Starting loads may need as much as 3 times the Running Wattage for Electrical Motors. Check your appliance rating before using generator.
0 4000500 1000 1500 2000 2500 3000 3500
Air Conditioner (12,000 BTU)
Air Conditioner (20,000 BTU)
Battery Charger 20 AMP
Battery Charger 12V DC
Belt Sander 3”
Bench Grinder 6”
Chain Saw
Circular Saw (6-12”)
Clothes Washer
Coffee Maker
Compressor (1HP)
Compressor (½ HP)
Compressor (3/4 HP)
Curling Iron
Demolition Hammer
Disc Sander (9”)
Edge Trimmer
Electric Blanket
Electrical Nail Gun
Electric Range - One Element
Electric Skillet
Freezer
Furnace Fan (1/3 HP)
Hair Dryer
Hand Drill (1”)
Hand Drill (½”)
Hand Drill (1/4”)
Hand Drill (3/8”)
Hedge Trimmer
Home Security
Impact Wrench
Jet Pump
Jigsaw
Lawn Mower
Light Bulb
Microwave
Milk Cooler
Oil Burner on Furnace
Oil Fired Space Heater (140,000 BTU)
Oil Fired Space Heater (30,000 BTU)
Oil Fired Space Heater (85,000 BTU)
Paint Sprayer, Airless (1/3 HP)
Paint Sprayer, Airless (handheld)
Portable Heater (5,000 BTU)
Radio
Refrigerator
Refrigerator/Freezer
Slow Cooker
Small Refrigerator
Submersible Pump (1 HP)
Submersible Pump (½ HP)
Submersible Pump (1-1/2 HP)
Sump Pump
Table Saw
Television
Toaster Oven
Water Heater
Weed Trimmer
1700
3300
500
110
1000
700
1200
800
1200
1000
2000
1400
1800
700
1300
1200
500
230
1200
1500
1250
500
1200
1200
1100
750
250
500
450
100
500
800
550
1200
100
700
1100
300
400
150
225
600
150
1550
50
600
1200
200
500
2000
1500
2800
600
1750
400
1500
4000
500
4

5
BEFORE OPERATION
Grounding the generator provides extra safety.
The 
WARNING Failure to properly ground the generator can result in electric shock.
A ground terminal connected to the frame of the generator has been provided on the front panel for this purpose. For
remote grounding, connect a length of heavy gauge (12 AWG min.) copper wire between the generator Ground Terminal
and a copper rod driven into the ground. This should provide a suitable ground connection. CPE recommends that you
consult with a local electrician to insure that local codes are being adhered to.
OPERATION
Add oil:
1) Place generator on a level surface.
2) Follow the oil grade recommendations and oil fill instructions given in the maintenance section of this manual.
CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil may result in engine
failure.
Add gasoline:
1. Use regular UNLEADED gasoline with the generator engine. Do not use premium gasoline. Do not mix oil with gasoline.
2. Clean area around fuel fill cap, remove cap.
3. Slowly add unleaded regular gasoline to fuel tank. Be careful not to overfill. Allow about ½” of tank space for fuel expansion.
4. Install fuel cap and wipe up any spilled gasoline.
WARNING Never fill fuel tank indoors.
Never fill fuel tank when Engine is running or hot.
Do not overfill the fuel tank.
Do not light cigarettes or smoke when filling the fuel tank.
WARNING
WARNING
WARNING
MODEL # C42412-1
Generator Specifications
Running Watts
Max Watts
AC Voltage
DC Voltage
Frequency
Phase
Power Factor
Engine
Fuel Tank Capacity
Running Hours
Noise Level
Overall dimensions
Gross Weight (with package)
Net Weight (without gas)
1200 Watts
1500 Peak Watts
120/240 V
12V
60 Hz
Single
1.0
2.4 HP OHV Champion Engine (EPA & CARB Certified)
1.45 gallons (5.50L)
7.5 Hours at 50% Load
65 dB (from 7 meters)
17.7” (L) x 13.8” (W) x 14.4” (H) - 45cm (L) x 35cm (W) x 36.5cm (H)
62.2 lbs. (28.2 kg)
57.3 lbs. (26 kg)

6
WARNING Do not use the choke on a warm engine or when restarting. The choke should only be used when starting the engine cold.
Do not attempt to connect 240 Volt loads to the 120 Volt receptacles.
Do not connect 50 Hz loads to the generator.
WARNING
FIG. 1 FIG. 2 FIG. 3 FIG. 4
WARNING
Stopping the Engine:
1. Unplug all
2. Let engine run at no-load for 30 seconds to stabilize the internal temperatures of engine and generator.
3. Move On/Off switch to “OFF”.
4. Close the fuel shut-off valve.
Start the generator:
1. Disconnect all electrical loads from the generator when starting the engine
2. Turn the fuel valve to the “On” position (Fig 1).
3. Set the On/Off switch to the “On” position (Fig 2).
4. Place the choke lever in the “Full” choke position by sliding it to the right as indicated in the illustration (Fig 3).
5. Grasp the recoil handle and pull slowly until slight resistance is felt. Then pull rapidly one time only to start engine (Fig 4).
6. Move the . When
engine is at operating temperature, move the choke to “Run” position (left).
7. Let the engine stabilize and warm up for a few minutes after starting.
8. For initial operation of a new generator, allow the engine to operate for 10 minutes before applying any electrical load.
9. Plug in the desired 120 Volt AC, single phase, 60 Hz electrical load.
1. Generator maintenance includes keeping the unit clean and dry.
2. Operate and st
Cooling air slots in the generator must not become clogged with snow, leaves or any other foreign material.
3. Check the
exterior surface.
4. Check the oil level and air cleaner cleanliness at each use.
5. Init
comes first.
6. Clean the air cleaner element every 50 hours (every 10 hours under dusty conditions.) Wash in high flash-point solvent. Squeeze dry, then
dip in clean engine oil and squeeze out excess oil.
7. Check and adjust the spark plug every 6 months or 100 hours, whichever comes first.
8. Replace the spark plug every year or 300 hours, whichever comes first.
9. Check and if n
months or 100 hours of operation.
MAINTENANCE
WARNING Improper maintenance or operating a defective generator could result in death or serious injury
CAUTION We DO NOT recommend using a garden hose to clean the generator. Water can enter the fuel system and cause
problems. In addition, if water enters the generator through cooling air slots, some of the water will be retained in voids
and cracks of the rotor and stator winding insulation. Water and dirt buildup on the generator internal windings will
eventually decrease the insulation resistance of these windings.

7
SERVICE INFORMATION
A = Intermittent use (less than 1 hour) or colder temperatures, below 60°F
B = Medium use (less than 3 hours) or seasonal temperatures 50°F 80°F
C = Extreme use (continuous use) or hot climates 80°F-100°F
Spark Plug, NGK or equivalent
Spark Plug Gap
Valve Clearance, Cold
A B6HS B B7HS C B8HS
0.70 / 0.80mm (.028 / .031 in.)
Intake 0.10 / 0.12mm (.004 / .005 in.)
Exhaust 0.10 / 0.12mm (.004 / .005 in.)
ADDING / CHECKING OIL LEVEL
1)Remove oil fill cap / dipstick to add oil
2)Add .42 qts. (0.40 L) oil and replace cap / dipstick
3)To check oil level - remove cap/dipstick and wipe it clean. Insert
cap/dipstick into the filler, but do NOT screw it in. Oil should
appear on dipstick.
4)If more oil is required add slowly
5)Oil should be filled at least to the bottom of the threads but not above the
top of the threads when on a level surface.
MAXIMUM FILL
MINIMUM FILL
DRAIN PLUG
DIP STICK
CAUTION This engine is equipped with a “low oil shut-off” and the engine will stop when engine oil falls below the minimum safe
level. Add oil immediately then restart engine.
CHECK ENGINE OIL LEVEL DAILY AND ADD AS NEEDED!
REGULAR SERVICE PERIOD : Perform at every indicated month or operating hour interval, whichever comes first.
EACH USE
FIRST
MONTH OR
5 HOURS
FIRST 10
HOURS
EVERY
3 MONTHS
OR 50 HOURS
EVERY
6 MONTHS
OR 100 HRS
ITEM
Check level
Change
Check
Clean
Clean
Clean-Readjust
Check-Readjust
Clean
Clean
Replace if necessary
Engine Oil
Air Cleaner
Sediment cup
Spark plug
Valve clearence*
Spark Arrester
Fuel tank and filter*
Fuel Line Every 3 years
°F-20 0 20 40 60 80 100 120
10W-30
5W-30 30
MAINTENANCE SCHEDULE:
* Recommended for experienced owner or service center.
• Tampering with the factory set governor could void your warranty.
• Improper maintenance will void your warranty.

8
TROUBLE SHOOTING GUIDE
PROBLEM CAUSE CORRECTION
Engine will not start Low on fuel or oil
Ignition switches in off position
Faulty spark plug
Choke in wrong position
Fuel shut-off valve in closed position
Unit loaded during start-up
Spark plug wire loose
Add fuel or oil
Turn to “ON” position
Replace spark plug
Adjust choke accordingly
Open fuel shut-off valve
Remove load from unit
Attach wire to spark plug
No electrical output Faulty receptacle
Circuit breaker kicked out
Defective capacitor
Faulty brush assembly
Faulty power cord
Faulty AVR
Loose wiring
Have Service Center replace
Depress and reset
Have Service Center replace capacitor
Replace brush assembly
Replace cord
Have Service Center replace AVR
Inspect and tighten wiring connections
Repeated circuit
breaker tripping
Overload
Faulty cords or equipment
Reduce load. Depress and reset
Check for damage, bare, or frayed wires. Replace
Generator overheating Generator overloaded
Insufficient ventilation
Reduce load
Move to adequate supply of fresh air, check for
air restriction
CHAMPION POWER EQUIPMENT
1 YEAR LIMITED WARRANTY
Warranty Qualifications:
Champion Power Equipment (CPE) will activate this warranty on receipt of your Warranty Registration Card and proof of purchase such as a
copy of your sales receipt from one of CPE's retail customers.
Warranty registration and your receipt must be submitted within ten (10) days from the date of purchase.
Champion Power Equipment Repair/Replacement Warranty:
CPE warrants to
period of one (1) year from the original date of purchase (90 days for commercial & industrial use). This warranty only applies to the original
purchaser and is not transferable.
Do not return the unit to the place of purchase.
Contact CPE's Technical Department and CPE will troubleshoot any problem with you over the phone or via e-mail. If the problem is not
corrected b
Service Center
without prior authorization, or at an unauthorized repair facility, will not be covered by this warranty.
Warranty Exclusions:
This warranty wil
overloaded the ge
surfaces are also excluded from this warranty. *Warranty is Limited to 90-days from purchase for Commercial users, including Rentals.
Limits of Implied Warranty and Consequential Damage:
Champion Power
claim by anyone from using this generator. This written warranty is the only warranty and any implied warranty will be limited by these terms.
This warranty gives you certain legal rights which may change from state to state. Your state may also have other rights you may be entitled to
that are not listed within this warranty.
An exchanged unit will continue the warranty from the purchase date of the original unit.

9
Champion Power Equipment, Inc (CPE),
The California Air Resources Board (CARB) and the United States Environment Protection Agency (U.S. EPA.)
Emission Control System Warranty
Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB)
emission regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
The California Air Resources Board, US EPA AND CPE are pleased to explain the Federal and California Emission Control Systems Warranty
on your 2005 and later, small off-road engine. In California, new, small off-road engines must be designed, built and equipped to meet the
State's stringent
EPA regulations for small non-road engines. CPE must warrant the emission control system on your small off-road engine for the period of time
listed below, provided there has been no abuse, neglect, unapproved modification, or improper maintenance of your small off-road engine.
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter and fuel
lines. Als
repair your small off-road engine at no cost to you including diagnosis, parts and labor.
MANUFACTURER'S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:
This emission control system is warranted for two years, subject to provisions set forth below. If, during the warranty period, emission related
part on your engine is defective in materials or workmanship, the part will be repaired or replaced by CPE.
OWNER WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your Owner's Manual. CPE
recommends that you retain all your receipts covering maintenance on your small off-road engine, but CPE cannot deny warranty solely for the
lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that CPE may deny you warranty coverage if your small, off-road engine or a
part has failed due to abuse, neglect, improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet, CPE dealer or CPE, Santa Fe Springs, Ca.
as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact:
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
Tel: [phone]
The emission warranty is a defects warranty. Defects are judged on normal engine performance. The warranty is not related to an in-
use emission test.
EMISSION CONTROL SYSTEM WARRANTY
The following are specific provisions relative to your Emission Control System Warranty Coverage.
Emission Control System Warranty (ECS Warranty) for 1995 and later model year California small off-road engines (for other states, 1997 and
later model year engines):
1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for other states, 1997 and later
model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use
purchaser, and shall continue for 24 consecutive months thereafter.
2. GENERAL EMISSIONS WARRANTY COVERAGE
CPE warra f-
road engines is:
a. Designed, built and equipped so as to conform with all applicable regulations adopted by the Air Resources Board pursuant to its authority in
Chapters 1 and 2, Part 5, Division 26 of the Health and Safety Code, and
b. Free from defects 
described in the engine manufacturer's application for certification for a period of two years.
3. The warranty on emission-related parts will be interpreted as follows:
a. Any w
Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or replaced by CPE according to Subsection “d”
below. Any such part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the ECS Warranty Period.
b. Any warran
for the ECS Warranty Period. A statement in such written instructions to the effect of “repair or replace as necessary”, shall not reduce the ECS
Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty
Period.
c. 
warranted for t
replacement, the part shall be repaired or replaced by CPE according to Subsection “d” below. Any such emissions-related part repaired or
replaced under the ECS Warranty, shall be warranted for the remainder of the ECS Warranty Period prior to the first scheduled replacement
point for such emissions-related part.

10
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of
the list applicable to the engine)
TO OBTAIN WARRANTY SERVICE:
d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be performed at no charge to the owner at a
CPE Authorized Service Outlet.
e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered by the ECS Warranty is in fact
defective, provided that such diagnostic work is performed at a CPE Authorized Service Outlet.
f. CPE 
warranty of an emission-related part covered by the ECS Warranty.
g. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-related parts sufficient to meet the expected
demand for such emission-related parts.
h. Any CPE Authorized and approved emission-related replacement part may be used in the performance of any ECS Warranty maintenance or
repair and will be provided without charge to the owner. Such use shall not reduce CPE's warranty obligation.
i. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids this ECS Warranty and shall be
sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable hereunder for failures of any warranted parts of a CPE
engine caused by the use of such an unapproved add-on or modified part.
Systems covered by
this warranty
Parts Description
Fuel Metering System
Air Induction System
Ignition System
Exhaust System
Miscellaneous Parts
Evaporative Emissions
Fuel regulator, Carburetor and internal parts
Air cleaner, Intake manifold
Spark plug and parts, Magneto ignition system
Exhaust manifold, catalytic converter
Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed systems
Fuel Tank, Fuel Cap, Fuel Line, Fuel Line Fittings, Clamps, Pressure Relief Valves,
Control Valves, Control Solenoids, Electronic Controls, Vacuum Control Diaphragms,
Control Cables, Control Linkages, Purge Valves, Vapor Hoses, Liquid/Vapor Separator,
Carbon Canister, Canister Mounting Brackets, Carburetor Purge Port Connector
You must take
purchas
service that CP
workmanship will not be denied because the engine was not properly maintained and used.
If you 
Customer service of Champion Power Equipment, Inc.
Champion Power Equipment, Inc.
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
[phone]
Attn: Customer Service
Customer Service: Mon. - Fri. 8:30 am - 5:00 pm (Pacific Standard Time)
Toll Free : 1 - 877 - 338 - 0999
Fax no. : 1 - 562-236-9429 (weekdays only)
Technical Service: Mon. - Fri. 8:30 am - 5:00 pm (Pacific Standard Time)
Toll Free : 1 - 877 - 338 - 0999
24hr. Voicemail: 1 - 626 - 230 - 5248 or E-mail: [email protected]

PARTS DIAGRAM
1
23
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36 37 38 39 40
41
42 43 44
45
46
47
48
49
7
7
50
51
11

PARTS LIST
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Part Number
GB5781-86- M6x22
GB859-86-φ6
GB96-85-φ6
GB41-86-M6
ST154FD-4010000
ST168F-1121100-C
GB5789-86-M6x12
ST154FD-4060000
ST154FD-4020000
ST154FD-4050000
ST154FD-4070000
ST02FD-1151204
ST154FD-4040000
ST154FD-4000003
ST154FD-4030000
ST154FD-2000003
GB/T6177-2000-M8
GB5789-86-M8x12
ST02FD-1151400-19
ST154FD-2000002
ST154FD-2000001
ST154FD-1000000
ST160F-1010002
ST154FD-1100100
ST154FD-1110000
GB/T41-2000-M8
ST168FD-1160400
ST168FD-1160100
ST154FD-1070200
ST168FD-1160200
GB5789-86-M6x20
ST168FD-1160300A
ST154FD-1070005-CPE
ST154FD-1070002-CPE
ST154FD-1070100
ST154FD-2001000
ST154FD-3000005
GB5789-86-M8x20
ST154FD-3001000
ST154FD-3000006
ST154FD-3002000
ST154FD-3000007
ST154FD-11004000
ST154FD-3000008
GB16674-1996- M5x12
GB859-87-φ5
GB97.1-85-φ5
ST154FD-3000001
GB5789-86- M5x20
ST168FD-1152004
ST154FD-3000004
Name
Bolt M6x22
Spring washer
Flat washer
Nut M6
Control panel
Engine saw
Bolt M6x12
DC socket
DC circuit breaker
AC circuit breaker
AC socket
Voltage meter
Condenser
Control panel cover
Wire protect hose
Vibration absorber
Nut M8
Bolt M8x12
Vibration absorber
Vibration absorber
Vibration absorber
Engine
Exhaust bolt
Exhaust gasket
Muffler
Nut M8
Fuel cock
Fuel meter
Fuel filiter
Fuel tank cap
Bolt M6x20
Vibration absorber washer
Clip
Fuel hose(CPE)
Fuel tank
Frame
Alternator front frame
Bolt M8x20
Rotor assembly
Stator cover
Stator assembly
Alternator center screw
Muffler support
Screw M6x90
Screw M5x12
Spring washer
Flat washer
Alternator rear cover
Bolt M5x20
Diode assy
Rear frame
Amount
1
2
2
2
1
1
6
1
1
1
1
1
1
1
1
2
10
2
4
1
1
1
2
1
1
2
1
1
1
1
4
4
2
1
1
1
1
4
1
1
1
1
1
4
2
2
2
1
1
1
1
12
12/05 -2