Changhong Electric LED42YC2000UA User manual

LED(BACKLIGHTING) COLOR
TELEVISION
OPERATION MANUAL
Please read this manual carefully before operation.
LED42YC2000UA

REGULATORY INFORMATION
This equipment generates,uses,and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
CAUTION
DO not attempt to modify this product in any way without written authorization from
supplier. Unauthorized modification could void the user's authority to operate this
product.
It is not recommended to keep a certain still image displayed on the screen for a long
time as well as displaying extremely bright images on screen.
Figures and illustrations in this User Manual are provided for reference only and
may differ from actual product appearance. Product design and specifications
may be changed without notice.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning
1

WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To
Rain Or Moisture.
The ventilation should not be impeded by covering the ventilation openings with
items, such as newspapers, table-cloths, curtains, etc.
The Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Attention should be drawn to the environmental aspects of battery disposal. Don’t
throw used batteries in dustbin. Please contact your retailer in order to protect the
environment.
When you install your TV, maintain a distance of at least 4 inches between the TV
and other objects (walls, cabinet sides, etc.) to ensure proper ventilation. Failing to
maintain proper ventilation may result in a fire or a problem with the product caused
by an increase in its internal temperature.
No naked flame sources, such as lighted candles, should be placed on the
apparatus.
To prevent the spread of fire, keep candles or other open flames away from this
product at all times.
The device may malfunction when under electrostatic discharge. It can be manually
resumed by recycling the power off and on again.
CAUTION connecting the Power Cord
Most appliances recommend they be placed on a dedicated circuit; that is, a single
outlet circuit which powers only that appliance and has no additional outlets or
branch circuits.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer. Protect the power cord
from physical or mechanical abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the
point where the cord exits the appliance.
The MAINS plug is used as the disconnect device, and the disconnect device shall
remain readily operable.
Operating Temperature: 0°C to 35°C Operating Humidity: ≤80%
Storage Temperature: -20°C to 60°C Storage Humidity: ≤90%
Warning
2

Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and
the U.S. Department of Energy helping us all save money and protect the
environment through energy efficient products and practices.
Home mode is the default as-shipped television configuration and settings. Home
mode is the setting in which the product qualifies for ENERGYSTAR. Any changes to
default as-shipped television configuration and settings would change the energy
consumption. Enabling certain optional features and functionalities may increase
energy consumption beyond the limitsre quired for ENERGY STAR qualification, as
applicable.
is a trademark of SRS Labs, Inc. TruSurround HD technology is
incorporated under license from SRS Labs, Inc.
SRS TruSurround HD™ creates an immersive, feature-rich surround sound
experience from two speakers, complete with rich bass, high frequency detail and
clear dialog.
Warning
3

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
7. Do not block any of the ventilation
openings. Install in accordance with the
manufacturer's instructions.
5. Do not use this apparatus near water.
8. Do not install near any heat source such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers)
that produce heat.
6. Clean only with a dry cloth.
9. Do not defeat the safety purpose of the
polarized or grounding type plug. A
polarized plug has two blades with one
wider than other. A grounding type plug
has two blades and a third grounding
prong. The wide blade or the third
prong is provided for your safety. When
the provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
Safety instructions
4

10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
13. Unplug this apparatus during
lightning storms or when unused for
long periods of time.
11. Only use the attachments/
accessories specified by the
manufacturer.
12. Use only with a cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in
any way, such as power supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been
dropped.
ON DISPOSAL
-The fluorescent lamp used in this product contain a small amount of mercury.
-Do not dispose of this product with general household waste.
-Disposal of this product must be carried out in accordance to the regulations of your
local authority.
NOTE
-If the TV feel cold to the touch, there may be a small "flicker" when it is turned on.
This is normal, there is nothing wrong with TV.
-Some minute dot defects may be visible on the screen, appearing as tiny red,
green, or blue spots. However there have no adverse effect on the monitor's
performance.
-Avoid touching the screen or holding your finger(s) against it for long periods of time.
Doin
g
so may produce some temporary distortion effect on the screen.
Safety instructions
5

UsingtheRemoteControl
When using the remote control, aim it at remote sensor on the television. If there is an
object between the remote control and the remote sensor on the unit, the unit may no
operate.
•Point the remote control at the REMOTE SENSOR located on the television.
•When using this television in a very brightly lit area, the infrared REMOTE CONTROL
SENSOR may not work properly.
•The recommended effective distance for using the remote control is about 7 metres.
Installing Batteries in the Remote Control
1. Open the cover at the back of the remote control.
2. Install two AAA size batteries. Make sure to match
the “+” and “-” ends of the batteries with the
diagram inside the compartment.
3. Replace the cover.
Battery Replacement
You will need to install the batteries into the remote control to make it operate following
the instruction below.
When the batteries become weak, the operating distance of the remote control will be
greatly reduced and you will need to replace the batteries.
Notes on Using Batteries:
The use of the wrong type of batteries may cause chemical leakage and/or explosion.
Please note the following:
•Always ensure that the batteries are inserted with the + and - terminals in the correct
direction as shown in the battery compartment.
•Different types of batteries have different characteristics. Do not mix different types.
•Do not mix old and new batteries. Mixing old and new batteries will shorten battery life
and/or cause chemical leakage.
• Replace batteries as soon as they do not work.
•Chemicals which leak from batteries may cause skin irritation. If any chemical matter
seeps out of the batteries, wipe it up immediately with a dry cloth.
• The batteries may have a shorter life expectancy due to storage conditions. Remove the
batteries whenever you anticipate that the remote control will not be used for an
extended period.
•The batteries (battery pack or batteries installed) shall not be exposed to excessive heat
such as sunshine, fire or the like.
CAUTION:
•It may result in an explosion if batteries are replaced incorrectly.
•Only replace batteries with the same or equivalent type.
Getting Started
6

CableInstallation
Before the installation and use, please read carefully the relevant content in “Warning and
Safety instructions”.
1. Take the TV from the wrapping package and put it in a drafty and flat place.
NOTE:
• When you plug or unplug the TV, computer or other equipments, you must make sure
that the AC power has been already shut down;
• When unplugging the power cable or signal cable, please hold the plug (the insulated
part), do not draw the body of the cable.
2. The RF output terminal can be connected with the RF input port of the TV.
3. The output AV terminal of a DVD can be connected with the AV input port of the TV
through an AV cable.
NOTE:
• Component and AV can not be used at same time for they share of one audio channel.
Component Y signal and AV video signal share one channel.
• Both Audio signals of AV and COMPONENT are input from "R - Audio - L".
4. The output COMPONENT (YPbPr) terminal of a DVD can be connected with the
COMPONENT (YPbPr) input port of the TV through an AV cable.
5. Connect one end of the VGA cable with the VGA port on the computer, connect the
other end of the VGA cable with the VGA port on the TV, and tighten the bolts
clockwise on each end of VGA cable.
NOTE:
• While connecting the 15-pin VGA, please do not insert the plug with enormous force,
otherwise the connector or a pin might be broken.
6. Connect one end of the HDMI cable with HDMI output port, connect the other end of
the HDMI cable with the HDMI port on the TV.
NOTE:
• While connecting the HDMI, please aim it carefully, and do not insert with enormous
force, otherwise the connector or a pin might be broken.
• HDMI1 and MHL share one port.
7. Sending the TV's digital audio signal to external audio equipment via the Digital Audio
Output port.
8. Check and make sure that all AV cables are connected with the corresponding ports
correctly.
9. Connect the AC power cable with 100-240V AC power supply.
NOTE：
• The range of input power for the TV is 100-240V~, 50/60Hz. Do not connect the TV
power input port with the AC power out of the above range.
• Please hold the insulated part of the plug when you are unplugging the power cable. Do
not touch directly the metallic part of the cable.
Connection and Setup
7

InstallationGuide
When the TV is initially powered on, a sequence of on-screen prompts will assist in
configuring basic settings. Press the ENTER button to start the guide. Press the button
to go to the next step. Press the button to return to the previous menu.
■TV Mode: Press the ▲/▼button to select retail or home.
■Language: Press the ▲/▼button to select the desired language using the OSD(On
Screen Display).
■Time Zone: Press the ▲/▼button to select your time zone.
■Time Format: Press the ▲/▼button to select 12-hour or 24-hour.
■Antenna: Press the ▲/▼button to select the signal type for channels.
■Auto Tuning: Scans and saves available programs automatically.
NOTE:
• If the TV doesn't receive any channels, please check your aerial connection or the
country you selected, then try an auto tuning again.
• If the TV just receives some of the channels, it means the aerial's reception isn't good
enough and an antenna service is recommended.
HotelMenu
Press the button to display the Source Menu, then press “2012” to enter into the
Hotel Mode to adjust the relative settings.
■Hotel Enable: Set the Hotel Enable On/Off by pressing the ◄/►buttons.
• When Hotel Mode is On, the Channel function is locked.
■On Source: Set the default signal source by pressing the ◄/►buttons. (The default
signal source will be displayed when the TV is turned on.)
■On Channel: Set the default channel by pressing the ◄/►buttons. (The default
channel will be displayed when the TV is turned on.)
■On Volume: Set the default volume by pressing the ◄/►buttons. (The default volume
is the volume when the TV is turned on. Remember the default volume should be less
than the maximum volume).
■Volume Max.: Set max volume by pressing the ◄/►buttons. When the max volume is
lower than the default volume, the max volume is the priority.
■Logo Select: When the "Hotel Enable" and "Logo Select" are both ON, the Logo is
displayed when power on.
■BACKUP: "BACKUP" means to write the TV data to USB device. The function is
supposed to be used when all the settings have been completed and the "Hotel
Enable" is ON.
■RESTORE: "RESTORE" means to read data from USB device and write to local flash,
then the machine needs a restart to initiate the parameters.
Connection and Setup
8

The buttons of the original remote control are as following:
Definition of the buttons on the remote control:
1. : Enter or quit the standby mode.
2. :Mute or restore sound.
3. TV/AV/HDMI/USB: Quick enter signal source.
4. COLOR BUTTONS: Red/green/yellow/blue key
navigation link.
:Fast reverse (in USB mode)
:Fast forward (in USB mode)
: Previous (in USB mode)
: Next (in USB mode)
5. MTS: The button can be used to switch between
Stereo/SAP/Mono in TV mode.
AUDIO: Switch Audio language in DTV mode.
6. :Press to display the Favorites program in TV
mode.(You should setup your favorite channels in
Program Edit menu)
7. :Play/Pause (in USB mode)
CC: Press to select the closed caption.
8. STILL: Freeze or activate the current picture.
: Stop (in USB mode)
9. INFO: Press to display the current program
information on the screen.
10. CH LIST: Press to call up the channel list. Press
again to exit it.
11. :Choose the aspect ratio.
12. :Selects the MHL mode directly; Moves back to
the main screen(In MHL mode).
13. MENU: Press to display/exit the on screen
menus or to quit some operations.
14. :Select signal source.
15. ▲/▼/◄/►: Select direction.
16. ENTER: Select or confirm menu item.
17. EXIT: Quit the current interface.
:Return to the previous menu screen.
(In MHL mode)
18. :Return to last viewed progra.
19. VOL+/VOL-: Increase/Decrease audio volume.
20. CH+/CH-: Scroll to next/previous channel.
21. SOUND: Changes the sound mode.
22. PICTURE: Changes the image mode.
23. NUMBER BUTTONS: Choose channels or
password importation.
24. -: In DTV mode, press number buttons and - key to
select channel.
25. SLEEP: Set the sleep timer.
NOTE:
•All pictures in this
manual are examples,
for reference only.
Actual product may
differ from the pictures.
•The buttons not
mentioned here are not
used.
20
21
22
ENTER
VOL CH
FAV AU D I O
MT S CC S T I L L
CH L I S T
IN F O
MENU
SOUND
PICTURE
SLEEP
TV AV H D M I USB
EX I T RECALL
23
24 25
Remote Control
9