Channel Master 3010 User manual

Mast
Nest/Bolts
Standout
Tape/Cable Tie
"F" Connector
Ground Block
Ground Rod
Four M6 x 12mm
screws and M6
external tooth
lockwashers from
hardware bag
Recess for
snap fit
Cover
Tabs (2)
DERUGIFCERUGIF
Cover
Inside Housing
Bosses for
M4 x 10mm
screws (2)
Cover tab
slots (2)
Inside rear wall
Channel Master
Mast
Nest/Bolts
Standout
Tape/Cable Tie
"F" Connector
Ground Block
Ground Rod
Four M6 x 12mm
screws and M6
external tooth
lockwashers from
hardware bag
Recess for
snap fit
Cover
Tabs (2)
DERUGIFCERUGIF
Cover
Inside Housing
Bosses for
M4 x 10mm
screws (2)
Cover tab
slots (2)
Inside rear wall
Channel Master
Front End
Hardware Bag
2 - M4 x 10mm self tap screws
(cover) 2 - M6 x 70mm hex head bolts
4 - M6 x 12mm self tap screws
(VHF elements) 2 - M6 flat washers
1 - mounting nest
(mast) 1 - rubber weather boot
4 - M6 external tooth lockwashers
LEFT
SIDE
RIGHT
SIDE
Main Unit
(bottom view)
VHF element
LEFT side
VHF element
RIGHT side
4 - M6 x 12mm
self tap screws
2 - M4 x 10mm
self tap screws
4 - M6 external
tooth lockwashers
PCB
VHF element
to slide
under PCB
Pre-installed
screw (halfway
turned down "4")
Line up the holes
in the element with
the holes in the
mounting bosses
Slide element slot in all of
the way (2 slots per element)
VHF slots
in housing
LEFT SIDE INSIDE VIEW
BERUGIFAERUGIF
Front End
Hardware Bag
2 - M4 x 10mm self tap screws
(cover) 2 - M6 x 70mm hex head bolts
4 - M6 x 12mm self tap screws
(VHF elements) 2 - M6 flat washers
1 - mounting nest
(mast) 1 - rubber weather boot
4 - M6 external tooth lockwashers
LEFT
SIDE
RIGHT
SIDE
Main Unit
(bottom view)
VHF element
LEFT side
VHF element
RIGHT side
4 - M6 x 12mm
self tap screws
2 - M4 x 10mm
self tap screws
4 - M6 external
tooth lockwashers
PCB
VHF element
to slide
under PCB
Pre-installed
screw (halfway
turned down "4")
Line up the holes
in the element with
the holes in the
mounting bosses
Slide element slot in all of
the way (2 slots per element)
VHF slots
in housing
LEFT SIDE INSIDE VIEW
BERUGIFAERUGIF
Front End
Hardware Bag
2 - M4 x 10mm self tap screws (cover) 2 - M6 x 70mm hex head bolts
4 - M6 x 12mm self tap screws (VHF elements) 2 - M6 flat washers
1 - mounting nest (mast) 1 - rubber weather boot
4 - M6 external tooth lockwashers
LEFT
SIDE
RIGHT
SIDE
Main Unit
(bottom view)
VHF element
LEFT side
VHF element
RIGHT side
4 - M6 x 12mm
self tap screws
2 - M4 x 10mm
self tap screws
4 - M6 external
tooth lockwashers
PCB
VHF element
to slide
under PCB
Pre-installed
screw (halfway
turned down "4")
Line up the holes
in the element with
the holes in the
mounting bosses
Slide element slot in all of
the way (2 slots per element)
VHF slots
in housing
LEFT SIDE INSIDE VIEW
BERUGIFAERUGIF

A
A
D
DD
J
E
F
G
H
I
K
L
B
B
B
B
C
CC
C
D
E
M
N
O
BC