Channel Master 1.8m Offset Tx/Rx Antenna System User manual

INSTRUCTION AND ASSEMBLY MANUAL
TYPE 183
1.8m Offset Tx/Rx Antenna System
US Sales Office • 1315 Industrial Park Drive, Smithfield, NC 27577 USA • Telephone: [phone] • Fax: [phone]
Germany Sales Office • Göppingerstr. 1, 75179 Pforzheim, Germany • Telephone: [phone] • Fax: [phone]
©2003 Channel Master LLC
8000660-02
ECN 9000000
5/03

VSAT ANTENNA/MOUNT/LNB
LIMITED TWELVE (12) MONTH WARRANTY
This CHANNEL MASTER®equipment is warranted to be free from defects in material and workmanship under normal
use and service.CHANNEL MASTER shall repair or replace defective equipment, at no charge, or at its option, refund the
purchase price, if the equipment is returned to CHANNEL MASTER not more than twelve (12) months after shipment.
Removal or reinstallation of equipment and its transportation shall not be at the cost of CHANNEL MASTER except
CHANNEL MASTER shall return repaired or replaced equipment freight prepaid.
This Warranty shall not apply to equipment which has been repaired or altered in any way so as to affect its stability or
durability, or which has been subject to misuse, negligence or accident.ThisWarranty does not cover equipment which has
been impaired by severe weather conditions such as excessive wind, ice, storms, lightning, or other natural occur-
rences over which CHANNEL MASTER has no control, and this Warranty shall not apply to equipment which has been
operated or installed other than in accordance with the instructions furnished by CHANNEL MASTER.
Claimants under this Warranty shall present their claims along with the defective equipment to CHANNEL MASTER imme-
diately upon failure. Non-compliance with any part of this claim procedure may invalidate this warranty in whole or in part.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER AGREEMENTS AND WARRANTIES, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION TOTHE
DURATION OF THIS WARRANTY. CHANNEL MASTER DOES NOT AUTHORIZE ANY PERSON TO ASSUME FOR IT
THE OBLIGATIONS CONTAINED IN THIS WARRANTY AND CHANNEL MASTER NEITHER ASSUMES NOR AUTHO-
RIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION
WITH THE EQUIPMENT DELIVERED OR PROVIDED.
IN NO EVENT SHALL CHANNEL MASTER BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE,
INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND.
In no event shall CHANNEL MASTER be liable for damages in an amount greater than the purchase price of the equipment.
Some states do not allow limitations on how long an implied warranty lasts, or allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you.
DATE DESCRIPTION REV.
5/03 ECN 9000000 Rel.

1
IMPORTANT!!!
INSTALLATION OFTHIS PRODUCT SHOULD BE PERFORMED ONLY BY A PROFESSIONAL INSTALLER
AND IS NOT RECOMMENDED FOR CONSUMER D.I.Y. (DO-IT-YOURSELF) INSTALLATIONS.
DANGER!!!
WATCH FOR WIRES! You can be killed if this product comes near power lines. Installation of
this product near power lines is dangerous. For your own safety, follow these important safety
rules.
1. Perform as many functions as possible on the ground.
2. Watch out for overhead power lines. Check the distance to the power lines before starting
installation.We recommend you stay a minimum of 6 meters (20 feet) from all power lines.
3. Do not use metal ladders.
4. Do not install antenna or mast assembly on a windy day.
5. If you start to drop antenna or mast assembly, get away from it and let it fall.
6. If any part of the antenna or mast assembly comes in contact with a power line, call your
local power company. DO NOT TRY TO REMOVE IT YOURSELF! They will remove it safely.
7. Make sure that the mast assembly is properly grounded.
WARNING!!!
Assembling dish antennas on windy days can be dangerous. Because of the antenna surface, even
slight winds create strong forces. For example, a 1.0m antenna facing a wind of 32 km/h (20 mph) can
undergo forces of 269 N (60 lbs). Be prepared to safely handle these forces at unexpected moments.
Do not attempt to assemble,move or mount a dish on windy days or serious,even fatal accidents may
occur. Channel Masteris not responsible or liable for damage or injury resulting from antenna
installations.
WARNING!!!
Antennas improperly installed or installed to an inadequate structure are very susceptible to wind
damage.This damage can be very serious or even life threatening.The owner and installer assumes
full responsibility that the installation is structurally sound to support all loads (weight,wind & ice) and
properly sealed against leaks. Channel Master will not accept liability for any damage caused by a
satellite system due to the many unknown variable applications.

Assembly Tools Required
1 - Compass 1 - 30mm or 1³⁄₁₆” Box End/Open End Wrench
1 - Clinometer 1 - 10mm Box End/Open End Wrench
1 - 220mm or 9” Magnetic Bubble Level 1 - 10mm Socket (For Torque Wrench)
1 - Torque Wrench 1 - 19mm or ³⁄₄” Deep Socket (13mm or ¹⁄₂”Drive)
(CAPACITY 5N-m-130N-m) 1 - 30mm (1.25”) Adjustable Wrench
1 - 24mm or ¹⁵⁄₁₆” Deep Socket 1 - 10mm or 1³⁄₁₆” Nutdriver
1 - Ratchet Wrench (13mm or ¹⁄₂” Drive) 1 - 30mm Socket (13mm or ¹⁄₂”Drive)
PREINSTALLATION MATERIALS CHECKLIST
Grounding Rod Clamp & Grounding Block - As Required by National Electric Code or local codes.
Ground Wire - As Required by National Electric Code or local codes (length required).
Coaxial Cable - Size and length required.
Concrete: See “Ground Pole” section for quantity.
M10 or #3 Rebar: See “Ground Pole” section for quantity. Deformed steel per ASTM A615, Grade 40 or 60.
The first and most important consideration when
choosing a prospective antenna site is whether or not the
area can provide an acceptable “look angle” at the
satellites. A site with a clear, unobstructed view is
preferred.Also consider obstruction that may occur in the
future such as the growth of trees.Your antenna site must
be selected in advance so that you will be able to receive
the strongest signal available.To avoid obstructions, etc.,
conduct an on-site survey with a portable antenna.
As with any other type of construction, a local building
permit may be required before installing an antenna. It is
the property owner’s responsibility to obtain any and all
permits.
Before any digging is done, information regarding the
possibility of underground telephone lines, power lines,
storm drains, etc., in the excavation area should be
obtained from the appropriate agency.
Because soils vary widely in composition and load capacity,
consult a local professional engineer to determine the
appropriate foundation design and installation procedure.
A suggested foundation design with conditions noted is
included in this manual for reference purposes only (see
page 4). To assist in the foundation design, refer to
“Antenna Windloads” in the Appendix “B” on page 15.
SITE SELECTION
DIN CLASS 5.6 DIN CLASS 8.8
M6 M8 M12 M16 M20 M22 M8 M12 M16
5 N-m 15 N-m 51 N-m 125 N-m 168 N-m 230 N-m 24 N-m 90 N-m 203 N-m
4 11 38 92 124 170 18 66 150
Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs Ft-Lbs
BOLT TORQUE
Head marking 5.6 or 8.8, if no head marking use DIN Class 5.6 values in above chart.
EXCEPTIONS TO ABOVE CHART:
• M12 x 100mm Round Head Square Neck Bolts securing Antenna to Mount.Torque to 27 N-m (20 ft-lbs.)
• M12 x 130mm Hex Head Bolts securing Feed Support to Backframe Tube.Torque to 47 N-m (35 ft-lbs.)
2

GROUND POLE INSTALLATION - 4.50” O.D.
16.7"
50"
96"
50"
C
L
55.5"
96"
50"
1" to 2"
SLOPE FOR
WATER RUN OFF
66"
2"
2"
APPROX.
4.5 O.D. (114.3mm) 4.5 O.D. (114.3mm)
ANT
1" to 2"
SLOPE FOR
WATER RUN OFF
GRADE GRADE
BUBBLE
LEVEL
BELOW
FROST LINE BELOW
FROST LINE
#3 REBAR x
DIA. OF PIER
INSERT THRU HOLE
IN TUBE & CENTER
#3 REBAR x DIA. OF PIER
INSERTTHRU HOLE IN
TUBE & CENTER
Ground Pole
Must Be
Vertical In
All Directions
Within .25 Inches
At Top
(6) #3 x 24" MIN.
AT 60˚APART
(SEE NOTE)
SEE
NOTE
d
MIN.
DIA.
d
MIN.
DIA.
NOTE:
66" may be increased,
concrete and length
of rebar will increase
accordingly.
WIND VEL. DIM “d” CONC VOL. DIM “d” CONC VOL. GROUND POLE
Inches (mm) CUYD (Cu Meter) Inches (mm) CUYD (CU Meter)
100 MPH 30”(762) .80 (.61) 24”(610) .70 (.54) “A”
125 MPH 37”(934) 1.2 (.92) 30”(762) 1.0 (.76) “B”
PIER FOUNDATIONS DEEP FROST LINE FOUNDATIONS
POLE SPECIFICATIONS:
Ground Pole “A”- 4.50 O.D. SCH 40 (4.026 I.D.) Steel - (Metric = 114.3 O.D. x 102.3 I.D. mm)
Ground Pole “B”- 4.50 O.D. SCH 80 (3.826 I.D.) Steel - (Metric = 114.3 O.D. x 97.2 I.D. mm)
NOTE:
1. Poles are not supplied (purchased locally to ASTM A501) and must be field drilled ⁵⁄₈ Dia. for M10 #3 rebar, drilled .218
(5.55mm) for ¹⁄₄-20 self tapping grounding screw and galvanized or painted for protection.
2. Pole and foundation design based on the following criteria:
a. Uniform building code Exposure C and 1.5 stability factory.
b. Vertical soil pressure of 2000 pounds per square foot. (9765 Kilograms/meter square)
c. Lateral soil pressure of 300 pounds per square foot. (1465 Kilograms/meter square)
d. Concrete compressive strength of 2500 pounds per square inch (176 Kg/Cm2) in 28 days.
CAUTION: The foundation design shown does not represent an appropriate design for any specific locality, since soil
conditions vary and may not meet design criteria given in Note 2.You should consult a local professional engineer to deter-
mine your soil conditions and appropriate foundation.
3

FIGURE 1.0
FIGURE 1.2 FIGURE 1.3
FIGURE 1.1
21 22
29
17
3
4
6
7
8
5
10
14
28
8
27
10
23
25
26
5
4
10
9
11
14
28
8
7
6
4 PLCS
YOKE
CAP
ASSEMBLY
GROUND
POLE
LOCKING
BOLTS
SOUTH
BACK
FRAME
ASSEMBLY AND INSTALLATION
1 - Place yoke cap assembly (25) onto ground pole.
Assemble channel and assembly to yoke cap assembly
with (4) M12 x 35mm Rd.Hd.Sq. Nk.(Item 27), flat washers
and hex nuts (5 & 26) as shown in Figure 1.0. Loosen
trunnion bolts.
Secure azimuth adjusting bolt (23) to yoke cap assembly
with M12 x 30mm hex bolt, lock washer and hex nut (4, 5
& 10). Point yoke cap assembly south and temporarily
secure to ground pole with locking bolts (Refer to Fig.1.2).
2 - Assemble bottom tube (14) to backframe (28) as
shown in Figure 1.1. Torque M12 Bolt (29) to 35-40 ft-lbs
(47-54 N-m).
3 - Install backframe assembly onto yoke cap assembly.
Secure with M20 x 140mm hex bolt and hex nut (9 & 11).
Loosen M12 hex bolt (10) and remove one M22 hex nut
(7) from elevation adjusting screw (6) and insert into
trunnion (8).Trunnion (8) in position shown is for 13˚and
above elevation. If elevation is less than 13˚, pivot
trunnion 180˚. Reinstall M22 hex nut (7). Do not tighten.
(Refer to Figure 1.3)
4 - Run up M22 hex nuts (7) on elevation screw (6) and
place backframe in birdbath position. (Refer to Fig. 1.3)
4

FIGURE - 1.7
FIGURE - 1.4
"UP"
(4 PLACES)
FIGURE - 1.8
FIGURE - 1.6
1
2
4
5
FIGURE - 1.5
15
16
17
TUBE
HOLE
FEED
SUPPORT TUBE
FEED
SUPPORT
19
15
17
16
14
19
513
13
12
SHORT FORMED END
OF SIDE STRUTS
ATTACHESTO FEED
SUPPORTTUBE.
LONG FORMED END 0F
SIDE STRUTS ATTACHES
TO ANTENNA.
LIFT UP ON FEED
SUPPORTTUBE HERE,
WHILE ANOTHER PERSON
TIGHTENS ANDTORQUES
HARDWARE ( & ).
TORQUETO 4 FT-LBS (5.4 Nm)
TORQUETO 43 FT-LBS (58 Nm)
*
***
*
*
*
**
17
18
3
3
20
17
18
5
5 - Insert four M12 x 100mm Round Head Square Neck Bolts
(1) into reflector (2) and place reflector onto backframe.
Secure reflector to backframe with four M12 lock washers and
hex nuts (4 & 5). Tighten and torque to 20 Ft-lbs (27 N-m).
Refer to Figure 1.4. Torque cross arm bolts (12) (Figure 1.1)
4 places to 40-45 ft-lbs (58 N-m).
IMPORTANT:“UP”arrow on reflector must be as shown in
Figure 1.4. Make sure Round Head Square Neck Bolts are
seated correctly before securing reflector to backframe.
Pre-torque (4) M12 x 35mm Round Head Square Neck
Bolts (Item 27) to 8-10 ft-lbs (12 N-m). (Refer to Fig. 1.0)
6 - Install M6 x 40mm hex bolt (15) with flat washer (16) into
bottom hole in reflector rim (2) and secure with M6 flat washer
and M6 hex nut (16 & 17). (Refer to Figure 1.5)
7 - Assemble feed support tube (19) onto backframe and
secure with two M12 x 130mm hex bolts (12).
IMPORTANT: M6 x 40mm hex bolt (15) in bottom of reflector
rim, fits into hole on top of support tube lower end.
NOTE: M12 tooth washer (13) must be assembled on
bolts (12), with one under head of bolts and one under
hex nuts (4).(Refer to Figure 1.6) Leave these bolts loose.
8 - Swing reflector down by loosening nuts (7) on elevation
screw (6).When reflector is in a convenient position, (approx-
imately 20˚), snug tighten nuts on elevation screw. (Refer to
Figure 1.3)
9 - Install left and right side struts (20) onto reflector as
shown in Figure 1.7.
Attach long formed end of side strut (20) to reflector rim by
inserting M6 x 20mm hex bolt (3) thru inside of rim and secure
snug, but free to pivot with M6 lock washer and hex nut (18 & 17).
Attach short formed end of side struts (20) to feed support
tube using M6 x 20mm hex bolt, lock washer and hex nut
(3, 18 & 17).
10 - IMPORTANT:Without using excessive pressure, lift feed
support tube vertically, just enough to relieve all loads off side
struts, while another person tightens and torque’s M12 hex
bolts (*) securing feed support tube to backframe to 35 Ft-lbs
(47 N-m) and M6 hex head bolts (**) securing side struts to
reflector to 4 Ft-lbs (5.4 N-m). (Refer to Figure 1.8)
11 - Install Feed/Feed Horn per instructions provided with
these items.

6
GROUNDING
TYPICAL ELECTRICAL GROUNDING FOR ANTENNA GROUND POLE
NOTE: All installations to conform to latest issue of National Electrical Code.
Ground antenna mount assembly and feed cables in accordance with current National Electrical code and local codes.
Figures 2.0 and 2.1 illustrates typical grounding methods for the ground pole and feed cables.
Clamps that provide a solid connection between ground wire and ground source should be used.
Tighten and torque all hardware.
GROUND WIRE
(Typical #10 AWG Copper, #8 Aluminum)
Refer to NEC Section 810 and local electric
codes for the specific area requirements.
¹⁄₄" - 20 UNC x ⁵⁄₈"
HEX HEAD, TYPE "D" POINT,
SELF TAPPING SCREW
GROUND LUG
¹⁄₄" EXTERNAL TOOTH
LOCK WASHER
Drill hole through one wall with
⁷⁄₃₂" Dia. twist drill.
Apply sealant here, after
assembly, to improve
corrosion resistance.
GROUND POLE
REF
10"-12"
NOTE:
ALL INSTALLATIONSTO
CONFORMTOTHE LATEST
ISSUE OFTHE NATIONAL
ELECTRIC CODE AND
LOCAL CODES.
FIGURE - 2.0
FIGURE - 2.1

7
ANTENNA ALIGNMENT PROCEDURE
Alignment with the satellite is obtained by setting
polarization, elevation, and azimuth. Charts 1, 2 & 3 are
to determine the values for your earth station antenna
site. “∆L”is the difference between the earth station
antenna site longitude and the satellite longitude. Use
“∆L”and your earth station latitude to obtain polarization,
elevation or azimuth setting.
POLARIZATION OF FEED
Loosen feed horn clamp bolts and turn feed clockwise or
counterclockwise, depending on being east or west of
the satellite as shown in Chart 1.Align marks on the horn
clamp and appropriate mark on the horn scale.
Polarization chart assumes antenna system polarization
is Tx vertical and satellite vertical Pol is perpendicular to
plane of geostationary arc. For horizontal Tx of antenna,
feed must be rotated 90˚from values shown. (Starting
point for polarization adjustment is 0˚, as shown in
Figure 3.0).
ELEVATION ADJUSTMENT
Use Chart 2 and determine your elevation setting. Using
a clinometer, adjust the elevation by turning the elevation
screw adjusting nuts until the desired elevation is
obtained. Reference Figure 3.1. Note: Degree values
shown on the clinometer are mechanical; that is
when the reflector face is vertical mechanical
elevation is 90˚ or axis is 0˚, while the beam elevation
(signal) axis is 22.62˚. Therefore as the reflector is
tilted, remember to compensate for the 22.62˚ offset
angle to get the correct beam elevation.
(See Appendix A, Outline Drawing, Page 14). This is
an approximate setting.Optimum setting will be achieved
during the fine tuning.
HORN SCALE
ALIGNMENT MARK
+400-40
CLAMP BOLT
PIVOT
BOLT
(LOOSEN)
ELEVATION
BOLT
(LOOSEN)
ELEVATION
ADJUSTING
SCREW
TRUNNION
CLINOMETER
ELEVATION
HEX NUTS
RIB
FIGURE - 3.0
FIGURE - 3.1

8
AZIMUTH
Use Chart 3 and determine your azimuth setting.
Values in chart must be adjusted for magnetic deviation
for your location for correct compass reading.
Equally tighten the six azimuth locking bolts until snug.
This will allow the reflector to rotate with slight resistance
(Ref. Fig. 3.2).
Rotate reflector and mount, pointing to the compass
reading for your location (Ref. Fig. 3.2).
Slowly sweep the reflector in azimuth until signal is
found. If desired signal is not found, increase or
decrease elevation setting and repeat the azimuth
sweep.Tighten locking bolts.
FINE TUNING
Progressively tighten and torque azimuth locking bolts to
75-85 Ft-lbs (108 N-m). The four top plate locking bolts
are pre-torqued to 8-10 ft-lbs. (12 N-m), maintain this
torque until after azimuth is fined tuned.
Use a signal strength measuring device for final adjust-
ments to obtain maximum antenna performance.
Alternate between elevation and azimuth fine tuning to
reach maximum signal strength, until no improvement
can be detected. Gradually tighten (1/8 turn increments
max.) top plate bolts in sequence 1, 3, 4 and 2 to
75 Ft-lbs., refer to Figure 3.2. Observe for maximum
signal strength as elevation screw’s M22 locking nuts are
tighten.
Polarization tune may be checked by carefully and slowly
rotating feed assembly in clamp. When maximum signal
strength is found, gradually tighten clamp bolts (Fig.3.0).
If a signal on the opposite polarity is available, this
signal should be minimized.
Tighten and torque all hardware. Refer to Torque Chart
on Page 2.
1
2
3
4
TOP PLATE
LOCKING BOLT
(4 PLCS)
AZIMUTH
ADJUSTING
SCREW
AZIMUTH LOCKING
BOLTS (4 PLCS)
TURN NUTS
CLOCKWISE OR
COUNTERCLOCKWISE
FOR AZIMUTH
FINETUNING
190
AZIMUTH
171°
COMPASS
NW
N
NE
E
SE
170
W
S
180
SW
ROTATE ANTENNA ON
GROUND TUBE
EXAMPLE:
AZIMUTH HEADING T0 171˚
(Azimuth ±Magnetic Deviation)
FIGURE - 3.3
FIGURE - 3.2

9

10

11

12
PARTS LIST
12
20
18
17
19
318 17 513
13
15
14
10
3
4
46
577
8
9
4
10
11
12
13
21 22 23 24
10
25
10
27
26
5
54
28
29
16
17
NO. DESCRIPTION QTY.
1 BOLT, CRG HD, GALV M12 X 100MM 4
2 REFLECTOR, 1.8m 1
3 BOLT, HEX HD, SS, M6 X 20MM 4
4 WASHER, LOCK, SS, M12 12
5 NUT, HEX, GALV, M12 15
6 SCREW, ELEVATION ADJ, GALV 1
7 NUT, HEX GALV, M22 2
8 TRUNNION 1
9 BOLT, HEX HD, GALV M20 X 140MM 1
10 BOLT, HEX HD, GALV M12 X 30MM 8
11 NUT, HEX, GALV M20 1
12 BOLT, HEX HD, GALV M12 X 130MM 2
13 WASHER, EXT TOOTH LOCK M12 4
14 BOTTOM BACKFRAME TUBE 1
NO. DESCRIPTION QTY.
15 BOLT, HEX HD, SS M6 X 40MM 1
16 WASHER, FLAT, SS M6 2
17 NUT, HEX, SS M6 5
18 WASHER, LOCK M6 4
19 WELDMENT, FEED SUPPORT TUBE 1
20 STRUT, SIDE FEED SUPPORT 2
21 WELDMENT, YOKE TOP PLATE 1
22 CHANNEL 2
23 AZIMUTH ADJ BOLT, M16 1
24 NUT, HEX, GALV M16 2
25 WELDMENT, YOKE CAP 1
26 WASHER, FLAT M12 4
27 BOLT, RD HD, SQ NK, M12 x 35mm 4
28 WELDMENT, BACKFRAME 1
29 BOLT HEX HD GALV., M12 x 18mm SPECIAL 4

13
MAINTENANCE
To ensure that the Tx/Rx Mount and 1.8m SMC Offset Antenna is operating efficiently and at an optimum, moderate main-
tenance is required. We recommend conducting as routine Maintenance Inspection every six months or as needed if
unusual circumstances occur, such as severe weather conditions, falling objects and vandalism.The following checklist is
provided for your convenience.
MAINTENANCE INSPECTION CHECKLIST:
1 - FOUNDATION
■Structural Damage
2 - Tx/Rx MOUNT
■All bolts (if any loosening has occurred tighten and torque - refer to Torque Chart Page 2)
■Structural Damage
■Corrosion of galvanized steel members (if necessary, repair with cold zinc-rich galvanizing paint)
3 - 1.8m SMC OFFSET ANTENNA
■Bolts - M12 round head square neck, securing antenna to mount (Correct torque 20 Ft-lbs/27N-m)
■Structural Damage
4 - BOTTOM FEED SUPPORT TUBE, SIDE FEED SUPPORT STRUTS AND ORU BRACKET
■All bolts (if loosening has occurred tighten and torque - refer to Torque Chart on Page 2).
■Structural Damage
■Corrosion of galvanized steel members (if necessary, repair with cold zinc-rich galvanizing paint)
5 - FEED ASSEMBLY
■All securing hardware
■Structural Damage
■Feed Horn Weather Cover - Physical Damage (if damaged, replace to prevent entry of water)
Upon inspection, make necessary repairs and replace any damaged parts.
For replacement parts, contact:
U.S.A. VSAT Customer Service
CHANNEL MASTER
1315 Industrial Park Drive
Smithfield, NC 27577
[phone] ■Fax [phone]

14
TYPE 183 1.8M OFFSET Rx/Tx ANTENNA SYSTEM
1 - DIMENSIONS SHOWN ARE FOR MODEL 6854 GROUND POLE (4.5" OD, SCH 40, Fy = 50 KSI) 2 - 50"TOTOP OF GROUND POLE MAY BE INCREASEDTO 68" IF MODEL 6861 GROUND POLE (4.5" OD SCH 80, Fy = 70 KSI) IS USED.
CONCRETE MUST BE INCREASED ACCORDINGLY (THIS WOULD INCREASE ALL VERTICAL DIMENSIONS BY 18").
OR 4", PIPE SCH 80, Fy = 36 KSI (4.5" OD X 3.83 ID) PURCHASED LOCALLY.
3 - CERTIFIED FOR 130 MPHWIND SURVIVAL.
NOTES:
+40
+40
+40
+40
27.9in
(70.90m)
(99.2cm)
39.1in
(34cm)
13.4in
(158.1cm)
62.2in
23fl
L
C
MECH AXIS ANTENNA
BEAM AXIS
(247.7cm)
97.5in
(35.1cm)
13.8in
(195.7cm)
77.1in
23fl
L
C
MECH AXIS ANTENNA
BEAM AXIS
(140.7cm)
55.4in
(44.6cm) 17.6in
(197.2cm)
77.6in
(182.2cm)
71.7in
L
C
APPENDIX A

MoBased on 55”(140.7cm) From Mounting Surface to C of Antenna.
*Kg = Pounds x .45359
**N-m = Foot-Pounds x 1.35582
Values shown above represent maximum forces for any wind direction.
Height and exposure factors from the uniform building code are NOTincluded.
L
15
FVMOFH= HORIZONTAL FORCE
FV= VERTICAL FORCE
MT= TORSIONAL MOMENT
MO= OVERTURNING MOMENT
+40
+40
(247.7cm)
97.5in
(35.1cm)
13.8in
23°
L
C
L
C
MECH AXIS ANTENNA
BEAM AXIS
(140.7cm)
55.4in
(44.6cm)
17.6in
APPENDIX B
ELEVATION FORCE MOMENTS
DEGREES (POUNDS)* (FOOT-POUNDS)**
MECH. BEAM FHFVMTMO
0 23 1824 -47 1073 8,436
10 33 1726 -365 1035 7,983
20 43 1677 -710 984 7,756
30 53 1519 -1008 892 7,025
40 63 1337 -1215 756 6,184
50 73 1166 -1337 635 5,393
60 83 972 -1398 491 4,496
70 93 729 -1082 378 3,372

16
HEX (PIVOT) BOLT, GALV. M20 x 140mm
ITEM 9
ROUND HD SQ NK BOLT, GALV.M12 x 100mm
ITEM 1
HEX HD BOLT, GALV. M12 x 130mm CLASS 8.8
ITEM 12
HEX HD BOLT, GALV. M12 x 30mm CLASS 8.8
ITEM 10
HEX HD BOLT, GALV. M12 x 18mm
ITEM 29
HEX HD CAP SCREW, SS
M6 x 40mm
ITEM 15
HEX HD CAP SCREW, SS
M6 x 20mm
ITEM 3
8.8
8.8
Hardware illustrations are true size. Place actual hardware on top of illustration to identify.
HARDWARE SORTER