Channel Safety Systems ENTRitech User manual

VIDEO DOOR ENTRY PANEL WITH KEYPAD USER’S MANUAL | 1/1
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
VIDEO DOOR ENTRY PANEL WITH KEYPAD USER’S MANUAL
CHANNEL SAFETY SYSTEMS t: 0845 884 7000
Peterseld Business Park f: 0845 884 6000
Bedford Road
Peterseld
Hampshire e: [e-mail]
GU32 3QA w: www.channelsafety.co.uk
Video Door Entry Panel with Keypad

VIDEO DOOR ENTRY PANEL WITH KEYPAD USER’S MANUAL | 1/2
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
Codes
The factory default master code is 1 2 3 4
To change the master code.
1. Remove power from the keypad
2. Apply power whilst holding down the key. The unit will then give a long continuous tone.
3. When the tone stops, release the key and enter your new 4 digit master code.
To enter programming mode.
1. Press the key, after 2 bleeps enter the 4 digit master code.
2. When you hear the 3 beeps and the LED ashes you are in the programming mode.
3. To exit programming mode press the key.
*
*
**
(Rear), screw allows
camera viewing
angle adjustment.
Light sensor
Call button
Security screw
Speaker unit
CCD camera
Illumination LED’s
Rain cover
D/ENT/VPAN/KP
SPECIFICATION
Input Voltage 12V-18V DC
Operating Temperature -10C ~ 55C
Stand-by Current 12mA
Operating Current 600mA
Camera 1/3” CCD
Illumination 0.05Lux
Mode Dual Transmission
Operating Time 2 minutes

VIDEO DOOR ENTRY PANEL WITH KEYPAD USER’S MANUAL | 1/3
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
Adding User Codes
1. Enter programming mode.
2. Enter a 2 digit user reference number (01-40).
3. Enter the 4 digit user code for the chosen user reference. If the chosen code is already in use the unit will emit a
long tone followed by two beeps. If the code is permitted then a two beep conrmation tone will sound.
4. Codes entered against user references 31-40 will latch the lock/relay open until the code is re-entered.
(commonly used for deliveries)
5. To enter further user codes repeat from step 2. To exit the programming mode press the key.
Deleting user codes
1. Enter programming mode.
2. Enter the 2 digit reference number (01-40) to be deleted, a two beep conrmation will be heard.
3. Press the key to delete user reference. A three beep conrmation tone will be heard.
4. To delete further user codes repeat from step 2. To exit the programming mode press the key.
Deleting a user code from an unknown user reference
1. Enter programming mode.
2. Press the key, the red LED remains on.
3. Enter the 4 digit user code to be deleted. Three beeps will be heard.
4. To delete further user codes repeat from step 2. To exit the programming mode press the key.
‘Delete All’
Warning only use in extreme circumstances, all settings will be lost.
1. Enter programming mode.
2. Press the key once, the unit bleeps twice, LED ashes.
Press the key a further 7 times. The unit will bleep 5 times & the LED will extinguish. All the user
codes are now deleted and the lock/relay time setting is changed to 1 second. The master code
is not aected.
Setting Lock/Relay time
The lock/relay will operate for a preset amount of time, factory setting is 5 seconds.
1. Enter programming mode.
2. Press 00 (this selects special user reference 00)
3. Enter the required lock/relay operation time 01-99 seconds
4. Press to exit programming mode.
#
#
#

VIDEO DOOR ENTRY PANEL WITH KEYPAD USER’S MANUAL | 1/4
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
The 12V Supply is switched on to, or away from the lock by the normally open or closed terminals. The type of lock
determines which terminal is used. Fail secure (N/O) Fail safe (N/C).
A time clock can be added to override user codes 10-20 & 36-40. This will stop codes within these ranges being
operative whilst the time clock input is active.
WIRING DIAGRAM – DC LOCK
EGR
0V
TIME CLOCK
N/O
COM
N/C
Red (Power 12V +ve)
Blue (Power 12V –ve)
Yellow (Audio)
White (Video)
-Ve
+Ve
L
O
C
K
Indoor Monitor Outdoor Keypad
Optional ‘Push
to open’ switch
12V DC PSU
Socket

VIDEO DOOR ENTRY PANEL WITH KEYPAD USER’S MANUAL | 1/5
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk

CHANNEL SAFETY SYSTEMS t: 0845 884 7000
Peterseld Business Park f: 0845 884 6000
Bedford Road
Peterseld
Hampshire e: [e-mail]
GU32 3QA w: www.channelsafety.co.uk
VIDEO DOOR ENTRY PANEL WITH KEYPAD USER’S MANUAL