Channel Safety Systems ENTRitech User manual

DDV INSTALLATION GUIDE | 1/1
t: 0845 884 7000 | w: www.channelsafety.co.uk
Digital Door Viewer Installation Guide
CHANNEL SAFETY SYSTEMS
Peterseld Business Park t: 0845 884 7000
Bedford Road f: 0845 884 6000
Peterseld e: [e-mail]
Hampshire w: www.channelsafety.co.uk
GU32 3QA
The new digital door viewer from
Channel Safety Systems

DDV INSTALLATION GUIDE | 1/2
CHANNEL SAFETY SYSTEMS
CONTENTS
1. Parts ........................................................................................................................................ 2
2. Installation ........................................................................................................................... 3-7
3. Operations ........................................................................................................................... 8
3.1. Digital Door Viewer Diagram ............................................................................... 8
3.2. Operating Instructions ........................................................................................... 9
3.3. Device Timing Operation ....................................................................................... 10
PARTS
1 Main Unit (Screen)
2 Doorbell Unit (Camera)
3 Metal Tube
4 Back Plate
5 Adhesive Backing for Doorbell Unit
6 128mb microSD card (Pre-Installed)
7 1 Short Screw
8 2 Long Screws
9 Flat Tool
12 3
456789

DDV INSTALLATION GUIDE | 1/3
t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTALLATION
1. Remove the current door viewer from your door. If you haven’t already
got a door viewer, drill a 5/8”inch hole.
2. Peel o the cover on one side of the Adhesive Backing and attach to
the back of the Doorbell Unit.
Then peel o the other adhesive cover.
3. Securely place the Doorbell unit on the outside of the door using the
Adhesive backing, ensuring that the metal threading is exactly in the
centre of the door viewer.
4. Be sure that the connection ribbon comes all the way through the hole.
BELOW: Existing door viewer and removal of
existing tting (outside of door)
RIGHT: Reverse of Doorbell Unit, remove cover
from Adhesive Backing and attach to unit
LEFT to RIGHT: Showing steps 3 & 4

DDV INSTALLATION GUIDE | 1/4
CHANNEL SAFETY SYSTEMS
Circuit board
LEFT to RIGHT: Peel o tape from Mounting plate, ensure correct positioning of
Circuit board, then place the metal tube into the hole, ensuring the connection
ribbon is through the centre and use the at tool to secure in place.
INSTALLATION CONTINUED...
5. Peel o the tape backing on the back side of the Mounting plate, this will
help prevent scratching on your door when attaching the main unit. Then
place the backing unit against the door and pull the connection ribbon
through the centre hole.
The circuit board goes in the right corner.
Place the metal tube into the hole and pull the connection ribbon
through the centre, using the Flat tool provided, twist the metal tube
clockwise until it is rmly in place.
6. Snap the PCB to the connection point.

DDV INSTALLATION GUIDE | 1/5
t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTALLATION CONTINUED...
7. Use a screw driver (not included) to help remove the faceplate from the
main unit.
Install two AA batteries into the Main unit (not included).
PLEASE NOTE!
For the following steps,
please note that the
main connection points
are vital to the Digital
Door Viewer’s operation.
If they are not properly
connected, the device
will not work.

DDV INSTALLATION GUIDE | 1/6
CHANNEL SAFETY SYSTEMS
INSTALLATION CONTINUED...
8. Place the unit on the door so that the two ports securely connect, ensure
that the unit is properly connected.
9. Use a Philips head screw driver (not included) along with the 2 long
screws included to mount the unit to the backing plate in two locations.
Replace the cover on the front of the device and using
the 1 short screw to secure the faceplate to the device.

DDV INSTALLATION GUIDE | 1/7
t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTALLATION CONTINUED...
The Digital Door Viewer is now fully installed.
Please note that both the screen and camera lens may have a clear plastic cover
to prevent scratching.
Please remove the plastic after installation.

DDV INSTALLATION GUIDE | 1/8
CHANNEL SAFETY SYSTEMS
OPERATIONS
Replacing the Batteries
To replace the batteries simply remove the faceplate of the main unit by unscrewing
the bottom screw of the device.
Remove the old batteries and replace them with two new AA batteries.
Refer to step 7 in the installation guide for more help.
Removing the mircoSD card
Remove the faceplate of the main unit by unscrewing the bottom screw on the
device. Remove the batteries from their position, push the microSD card in to release
it. You can now view the images from the card on another device or replace the
microSD card with more/less memory.
DIGITAL DOOR VIEWER DIAGRAM
Buttons:- The Digital Door Viewer has 4 buttons, A, B, C & D.

DDV INSTALLATION GUIDE | 1/9
t: 0845 884 7000 | w: www.channelsafety.co.uk
OPERATING INSTRUCTIONS
Take a picture from the inside:
To monitor who is outside your door, you can press the power button,“A”, the screen
will turn on after 3 seconds. When the screen is on press“A”to take a picture. The
display will be in‘Live mode’for 10 seconds and then time out.
Take a picture using the doorbell:
When the visitor presses the start button, “B”, the main device screen will turn on after
6 seconds, and the unit will take a picture automatically. The screen will stay on for an
additional 30 seconds. The included 128MB microSD card stores over 1200 pictures.
Review and Delete pictures:
When the screen is on press“C” to review all pictures taken before, scroll to see all
pictures one by one. Press “D” to delete any unwanted pictures. Press“D” again to
conrm that the image selected is the image you wish to delete.
Change the Date & Time:
Once the screen is on press“D” which can then adjust the date & time. Press “C” or“D”
to increase and decrease the date & time, press “A” to skip to the next menu. After you
have chosen the correct date & time press and hold “A” for 3 seconds and the system
will store the information automatically.
Screen Shots:

DEVICE TIMING OPERATION
Digital Door Viewer Installation Guide
CHANNEL SAFETY SYSTEMS
Peterseld Business Park t: 0845 884 7000
Bedford Road f: 0845 884 6000
Peterseld e: [e-mail]
Hampshire w: www.channelsafety.co.uk
GU32 3QA
CHANNEL SAFETY SYSTEMS