Multitek MULTIBUS MB-09 User manual

1
MULTIBUS USER MANUAL
(MB-09, MB-10, MB-02, MB-04, MB-03,MB-05)
It obeys the rules of AEEE regulations.

2
MULTIBUS MB-09 and MB-10 DOOR PANEL USER MANUEL
Note: Some panels have ENT, CLR and some panels have ARA,SILbuttons on the keypad.
ENT/ARAand CLR/SILbuttons have the same functions.
1. CALLING BY NAME:
Name list can be shown by pressing ENT key. Select the name using up (2), down (8), right (6), left
(4) keys
Dial the name by pressing ENT key.
2.PROGRAMMING THE PANEL:
Main menu may appear by pressing ENT and 99 digits.
Software version can be shown, pressing ENT key when the arrow cursor is on the VERSION.
To enter to the program menu,bring the cursor on PROGRAM line by playing up (2), down (8) keys ,
then press ENT key.
Then,you need to enter the program password of 4 digits.
Note: Default program password is 7447.
a) CHANGE PASSWORD (CHANGING PROGRAM PASSWORD)
Select the CHANGE PASSWORD line on the program menu, and press the ENT key and dial 4 digits
new password and press ENT.
Note: The consecutive digits like 1234 or 5678 may not be assigned as password. When you forget
your program password, please call authorized service.
VERSION
PROGRAM
PROG.PASSWD?
CHANGE PASSWRD
DOOR NR
ENTER NAMES
CLEAR LIST
BLOCK NO
UNLOCK DURATION

3
b)DOOR NR (ASSIGN DOOR PANEL NUMBER)
If there are more than one door in a block you need to assign door number to each door panel .Place the
cursor on DOOR NR using up (2), down (8) keys on the program menu and press ENT key.
Assign the door number using up (2), down (8) keys then press ENT.Maximum door number may be 4.
c)ENTER NAMES ( ENTERING ROOM NAME)
Place the cursor on ENTER NAME pressing the up (2), down (8) keys at the program menu and press
ENT key.Then , enter the name as followings:
NO: Enter the flat number with keypad and press ENT key and go to the name section.
AD: You can write the room name with the keypad selecting the letters given in the keypad below.
Then press ENT. Door panel will return to the main screen and the name will be registered.
d) CLEAR LIST (TO DELETE THE NAME LIST)
Place the cursor to CLEAR LIST using up (2), down (8) keys and press ENT key. All names will be
deleted from the list.
e) BLOCK NO (DEFINING THE NUMBER OF THE BLOCK)
The system may be used with many blocks of apartments and one guard.When the guard calls the rooms
he should know/dial the block number and the room number.Because of that ,the block number may be
needed to enter to the first door panel.
By using the up (2), down (8) keys on the menu BLOCK NO is selected. ENT is pressed and the
NO: 02
AD: MULTITEK

4
doorpanel block number is entered. The block number may be up to 30.
f)UNLOCK DURATION (DOOR UNLOCK DURATION)
Door release time of the door lock may be needed to adjust.
Bring the cursor UNLOCK DURATION line by playing up (2), down (8) keys.
Then press ENT. Adjust the time interval from 01 to 99 seconds using up (2), down (8) ,then press
ENT.
3.TO DEFINE A DOOR OPENING PASSWORD:
Each flat may define her password seperatelly.
Call the flat whose password will be defined .After the connection is established the person in the flat
presses F1 key.The person in front of the door panel enters 99 and 4 digit opening password .
99 + XYZT
Note: Consecutive digits like 1234 or 5678 may not be assigned as password. If the door panel gives an
error tone it means the password is not accepted.You need to re-enter new password.
Example:To define a door opening password to room number 2:
Call the room number 2 and establish the conversation.
Press F1 key on the monitor.Enter 99 + XYZT on the door panel side. xyzt becomes the password of
room number 2.
OPENING THE DOOR WITH THE PASSWORD :
Enter 99 + 4 digit number password with keypad of the door panel.
Example: If the password (of any room) is 1453 you enter the following digits to the door panel:
99 1453
The door opener is released.
NOTE: If there is a mistake CLR key can be used to clear.

5
4.WIRING DIAGRAM OF MB10 PANELS
NOTES
1. The total number of external cameras connected to a building cannot be more than 5.
2. The number of external cameras connected to the door panel is defined by programming.
3. The image of the camera door panel and external cameras in a building is taken by repeatedly
pressing the button on the monitor.

6
MULTIBUS MB-05 and MB-03 DOOR PANEL USER MANUEL
PROGRAM PASSWORD:
4-digit program password is used to define the block number from the door panel, to define the door
number etc. Initial value of program password is 7447.
In the following programming sections the program password is written as SSSS.
SSSS = Programing Password (Default 7447)
CHANGE PROGRAM PASSWORD:
The current program password + 2 + new program password is keyed in the door panel. Program
password changed.
SSSS + 2 + YYYY
Note: The password consisting of consecutive numbers cannot be entered. Your device must be
reprogrammed when you forget your program password.
Defining Whether A Doorkeeper Exists
Program password + 3 + 0 or 1 is keyed in the door panel.
SSSS + 3 + DOORKEEPER
DOORKEEPER: 0 Doorkeeper availabe. (Default 0)
DOORKEEPER: 1 Doorkeeper not available.
Identify The Door Panel Number
Program password + 0 + Door Number is keyed in the door panel.
SSSS + 0 + K
With the door no, you set how many doors are in the block. Maximum number of doors 4 types.
Opening The Outside Door With A Password
A password can be defined for each apartment.
Defining The Door Opening Password
The number of the circle to determine the password from the outer door panel is given. Press the F1 while
removing the handset from the dialed apartment.
After press the F1. At the outer door panel, first 99 keyed, followed by a 4 digit password.
99 + XYZT
Note: The password consisting of consecutive numbers (1234, 5678 etc.) cannot be entered. When a
sequential number is entered, alerted by a faulty input tone by the outside door panel. Change the
password and login again.
Example: To set the password for apartment number 2;
2 + ENT called
Removing the handset from the apartment and press F1.
Entered the panel 99 + 1453

7
The password of apartment 2 becomes 1453
Opening The Outside Door With A Password
Entered the panel 99 + 4 digit password (XYZT)
Example: Apartment 2 password: 1453
Entered the panel 99 + 1453 and door is opened.
Note: If you entered wrong, you can delete with CLR.
Defining The Block Number
4-digit password + 1 + block number is keyed in the door panel.
SSSS + 1 + BB
With the block number, you determine which block the device is in. Maximum block number is 30.
Defining The Door Automaton Time
4-digit password + 4 + door automaton time is keyed in the door panel.
SSSS + 4 + SN
Automatic door pulling time is between 01-99 sec.
Deleting Door Opening Passwords
SSSS + 5

8

9
MULTIBUS MB-04 and MB-02 DOOR PANEL USER MANUEL

10
Note:This cabling is done in the sound system building. Between block doors and guard phone are serially
cabling with ground cable (PD-PAP 4X0.5).
Block doors and guard phone are wiring parellely the cable.
See the site applications of video systems for connection details.

11
WIRING INSIDE BUILDING
3.VIDEO SYSTEM ( No Guard and
No Doorkeeper) General Cabling
a) 12 Floor (Up to 80 Rooms)
Work with 4 cables.
Multitek DT5 or H03VH-H 2x1 mm2
(red,green)
KPD-V 2x0.5 mm2 (yellow, black, pink)
Not: For more floors and apartment floors
Use H03VH-H 2x2.5 mm2 cable.

12
b) 6 Floors (Up to 40 floors) Works with CAT5/CAT6/DT8. (Connection diagrams are as
follows)

13
1-VIDEO AMPLIFIER (V-DIST 4+1) CONNECTIONS DIAGRAMS (4 COLUMN)
Video amplifier is used to amplify the video signal in column-type installations and mounted near the door
panel.
Notes:
1-Column-shaped installations, the number of columns in the building is more than one video amplifier V-
DIST 4+1 is used.
2- The video amplifier's supply system is taken from the 18VDC adapter. Cable is taken from the end of the
adapter + (18VDC) wires to the input of a cable amplifier 18v, Cable is taken from the end of the adapter -
(GND) wires to the input of a cable amplifier VGND and GND.
3- The black video end of the ring panel is connected to the VıDEO ıNPUT end of the video amplifier. Video
1,2,3,4 and VIDEO OUT ends are connected to black color video end of 1,2,3,4,5 column lines respectively.
The VIDEO INPUT end of the amplifier is connected to the VIDEO IN terminal of a second video amplifier
to obtain a more falza column when necessary.

14
4- Important: For column installations, a 75 ohm resistor must be installed between the black (video)
and green (GND) cables in the last circle of each column. and between the monitors 75 ohm
resistances must be removed.
Important: A 75 ohm terminating resistor must be fitted between the V-DIST-4 + 1 video amplifier and the
VINPUT and GND terminals.
EXAMPLES: DISTRIBUTION OF THE INSTALLATION CABLE TO FLOOR
APARTMENTS
If you have a plumbing system installed on the floor from one point to another, use the MB-DIST video
distributor. The video distributor prevents video distortion.

15

16
SUMMARY
PRODUCTS TO BE USED IN MULTIPLE SYSTEM
1. Number of video amplifiers to be used in MULTIBUS system
it is only used for column cable installations and is required to be placed near the door panel, 5 columns
need 1 piece.
2. Number of MB-DIST video distributors to be used in MULTIBUS system
The junction box is used to connect 1 MB-DIST video distributor to each floor in horizontal installations.
3. Number of PS-18E adapters to be used in the MULTIBUS system
1 PS-18E for up to 40 apartments
2 PS-18E for up to 100 apartments
1 RED-18E for more than 100 apartments in
4. Number of cables to be used in the MULTIBUS system
NUMBER OF FLOOR
CABLE TO BE USED
Up to 6 times (max. 40 monitors) (longest cable
cable approx. 30 m)
more floors
CAT5/CAT6/CAT8 OR MULTİTEK DT5
Up to 12 floors (max. 80 monitors) (longest cable
cable approx. 50 m)
MULTİTEK DT5 or H03VH-H 1X2X1 mm2 and
KPD-V 3X0.5 mm2
More floors
H03VH-H 1X2X2.5 mm2 and KPD-V 3X0.5 mm2
DATE: 14.02.2019 REVISION DATE: REVISION NO: DOCUMENT NO: MLŞ14- 39/2 PAGE NO: 16/16