Chanson Water VS-30 User manual

Under Counter
Alkaline Water Ionizer
User Manual
Before using the instrument, be sure to carefully read through the instructions contained in this manual.
The PH-value mentioned in this manual and panels varies depend on different water quality.
Chanson shall not be liable for any malfunctions or accidents occurred from the user's
ignorance and misuse during installation cause.
Life - Health - Happiness

1.The first section of alkaline water The PH-value lies between 8.0 and 8.5,
It's for first time to drinking and should range between 20-35 years old.
2.The second section of alkaline water The PH-value lies between 8.5 and
9.0, It's for that people used to drink alkaline water and also good for
people of ages of 35-45 years old.
3.The third section of alkaline water The PH-value lies between 9.0 and 9.5
, for ages range above 45 years old and daily drinking. It's good to Improve
some chronic diseases.
4.The forth section of alkaline water The PH-value lies between 9.5 and 10
, for food cleaning and odors.
5.The first section of acid water The PH-value lies between 5.0 and 6.0 and
it's light acid. for skin cleaning and making pores smaller.
6.The second section of acid water The PH-value lies between 2.9 and 4.0
and it's mild acid, for dish washing and antibacterial purpose.
You can benefit most from drinking alkaline water when
(1)You feel hungry before meals.
(2)Between half hour before meals and 2 hours after meals.
It influences the process electrolytic cell that most public water supplies
provide hard water. please clean and care the electrolytic cell periodically.
1.Alkaline water ionizer is an antacid. Antacids help to treat the acid of
human body to prevent from ill and chronic disease.
2.Alkaline water ionizer function as an antioxidant and seeks out free
radicals to prevent from ill and chronic disease.
3.Alkaline electrolyzed water increases the Lactobacillus count and improves
fermentation.
4.The water ionizer molecule structure (groups of H O molecules)
2
size is reduced. It is easy to be absorbed by drinking and accelerates the
metabolism to keep you young and healthy.
5.There're more minerals in alkaline water ionizer than ordinary water to
satisfy daily mineral requirement.
6.Acid water could be used for beauty salon face washing and
antibacterial purpose.
What are the benefits of alkaline water ionizer
Suggestions for drinking alkaline water ionizer
1
1. Safety and misuse warnings
.....................................................................................................
2. Accessories and required tools
.....................................................................................................
3. Product overview after installment
.....................................................................................................
4. Installment explanation
.....................................................................................................
5. The instruction of measuring PH
The instruction of replacing filters
Using the tank for calcium powder
.....................................................................................................
6. VS-30/50/70 water faucet directions
.....................................................................................................
7. VS-30/50/70 functions
.....................................................................................................
8. VS-30/50/70 LCD functions guideline
.....................................................................................................
9. VS-30/50/70 LCD display directions
.....................................................................................................
10. VS-30/50/70 specification
.....................................................................................................
11. The process during blackout and water suspension
.....................................................................................................
12. VS-30/50/70 simple trouble shooting guidelines
.....................................................................................................
13.Filter maintenance record
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
2~3
4
5
6~8
9
10
11~13
14~17
18~20
21
22
23
24~25
Contents
The Feature And Benefit
Of Alkaline Water Ionizer

1.The first section of alkaline water The PH-value lies between 8.0 and 8.5,
It's for first time to drinking and should range between 20-35 years old.
2.The second section of alkaline water The PH-value lies between 8.5 and
9.0, It's for that people used to drink alkaline water and also good for
people of ages of 35-45 years old.
3.The third section of alkaline water The PH-value lies between 9.0 and 9.5
, for ages range above 45 years old and daily drinking. It's good to Improve
some chronic diseases.
4.The forth section of alkaline water The PH-value lies between 9.5 and 10
, for food cleaning and odors.
5.The first section of acid water The PH-value lies between 5.0 and 6.0 and
it's light acid. for skin cleaning and making pores smaller.
6.The second section of acid water The PH-value lies between 2.9 and 4.0
and it's mild acid, for dish washing and antibacterial purpose.
You can benefit most from drinking alkaline water when
(1)You feel hungry before meals.
(2)Between half hour before meals and 2 hours after meals.
It influences the process electrolytic cell that most public water supplies
provide hard water. please clean and care the electrolytic cell periodically.
1.Alkaline water ionizer is an antacid. Antacids help to treat the acid of
human body to prevent from ill and chronic disease.
2.Alkaline water ionizer function as an antioxidant and seeks out free
radicals to prevent from ill and chronic disease.
3.Alkaline electrolyzed water increases the Lactobacillus count and improves
fermentation.
4.The water ionizer molecule structure (groups of H O molecules)
2
size is reduced. It is easy to be absorbed by drinking and accelerates the
metabolism to keep you young and healthy.
5.There're more minerals in alkaline water ionizer than ordinary water to
satisfy daily mineral requirement.
6.Acid water could be used for beauty salon face washing and
antibacterial purpose.
What are the benefits of alkaline water ionizer
Suggestions for drinking alkaline water ionizer
1
1. Safety and misuse warnings
.....................................................................................................
2. Accessories and required tools
.....................................................................................................
3. Product overview after installment
.....................................................................................................
4. Installment explanation
.....................................................................................................
5. The instruction of measuring PH
The instruction of replacing filters
Using the tank for calcium powder
.....................................................................................................
6. VS-30/50/70 water faucet directions
.....................................................................................................
7. VS-30/50/70 functions
.....................................................................................................
8. VS-30/50/70 LCD functions guideline
.....................................................................................................
9. VS-30/50/70 LCD display directions
.....................................................................................................
10. VS-30/50/70 specification
.....................................................................................................
11. The process during blackout and water suspension
.....................................................................................................
12. VS-30/50/70 simple trouble shooting guidelines
.....................................................................................................
13.Filter maintenance record
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
2~3
4
5
6~8
9
10
11~13
14~17
18~20
21
22
23
24~25
Contents
The Feature And Benefit
Of Alkaline Water Ionizer

Read carefully the instructions contained in this manual.
Please follow the instructions below to prevent the misuse and avoid
injury to the user and other persons as well as damage to property.
Warning
This symbol indicates warning that, if ignored or applied incorrectly,
creates the danger of death or serious personal injury.
This symbol stipulates matters that have the risk of causing death or
serious injury if the product is operated incorrectly while ignoring this
indication.
This symbol ( ) means that the indicated
action must not be performed. Indications
within or nearby this symbol are specifically
prohibited.
This symbol ( ) means that the indicated
action must be performed.
23
Safety Precautions MUST follow
the instructions.
If instructions ignored and applied incorrectly,
creates the injury or damage which is labeled
by the following symbols.
Please follow the instructions below.
Caution
Warning
Caution
Safety Precautions MUST follow
the instructions.
Decompilation or disassembly is prohibited.
Don't try to disassemble, maintenance,
rebuild, or alter by yourself.
To disassemble creates therisk of fire and
electric shock.
If the dirt or dust from getting on the outlet,
that will creates the risk of electric shock by humidity.
Do not damage power cord and outlet.
Using multi-socket and household extension
cords can create the risk of fire by heating.
Do not touch socket with wet hands.
That creates the risk of electric shock and
injury.
Power plug must be plugged in completely
Do not use worn socket and loose plug.
If device fall into water, please unplug from
the electrical socket and stop using.
Please contact your original retailer or an
authorized service provider.
Do not use unqualified water.
Water without anti-bacteria process or
moving the hazard material out creates
the risk of ill. Qualified water supply is
recommended.
Keep using worn power cord or outlet
creates the risk of fire, electric shock,and
short circuit.
Positioning by brad nails.
Power cord was worn.
Rebuild or alter by yourself.
Twist or bend the power cord .
Pull on the power cord
Put heavy weight on power cord.
Bend power cord as loop
Please clean the dust or dirt over the outlet
periodically.
Avoid multi-socket and household extension
cords. Do not over voltage.
Do not drink the water which pH-value is over 10.
That will creates the risk of injury. The water
which pH-value is around 9.5 is recommended.
The third section of alkaline water is also
recommended.
strong alkaline water(PH10) and acid water.
Water from drainage pipe
Water from outlet during electrode cleaning
May cause uncomfortable feeling.
If pre-filter is installed and being absent
without producing electrolyzed alkaline
water more than 2 days, MUST turn off the
water inlet switch.
May cause water leakage and water pipe
burst because of high pressure.
Before the first appliance of each day,
please let the water flow freely about 0.
6 liter(about 15 seconds) and then begin
to use.
Using such containers will cause them to
discolor or to be worn.
Contact our service providers about
fees of the related maintenances.
The following persons should contact doctor
before using weak acid water.
Avoid using aluminium containers which
anti-alkali ability is weak. Avoid using
copper containers without anti-acid ability
For electrolyzed alkaline water or clean
water, please store it at clean closed
containers. Drink up in 1 day at normal
temperature. Drink up in 2 days for
storing at refrigerator.
As chlorine in water is removed, it's easy to
be addled to cause injury.
Do not use unqualified water.
Low skin resistance .
With over-sensitive skin.
For drinking electrolyzed alkaline water for
the first time, please drink 1 or 2 cups of the
first section of alkaline electrolyzed water
daily. After 2 weeks and body can accept
alkaline electrolyzed water, then drink the
second or the third section of alkaline
electrolyzed water.
To drink highly alkaline watermay cause
uncomfortable feeling.
Do not use hot water with the temperature
over 40 through pre-filters or device.
That may case the damage of filters and device.
In a hard-water area, electrodes cannot
function properly. Avoid being dysfunctional
and losing of water quality, please clean
and maintenance periodically.
Over two days.plpase let the water flow
freely about 8 liter (about 3 minutes) and
then begin to use.
If go out over one day or absent withant using water ioniter more than one day, must turn off power and water inlet switch.

Read carefully the instructions contained in this manual.
Please follow the instructions below to prevent the misuse and avoid
injury to the user and other persons as well as damage to property.
Warning
This symbol indicates warning that, if ignored or applied incorrectly,
creates the danger of death or serious personal injury.
This symbol stipulates matters that have the risk of causing death or
serious injury if the product is operated incorrectly while ignoring this
indication.
This symbol ( ) means that the indicated
action must not be performed. Indications
within or nearby this symbol are specifically
prohibited.
This symbol ( ) means that the indicated
action must be performed.
23
Safety Precautions MUST follow
the instructions.
If instructions ignored and applied incorrectly,
creates the injury or damage which is labeled
by the following symbols.
Please follow the instructions below.
Caution
Warning
Caution
Safety Precautions MUST follow
the instructions.
Decompilation or disassembly is prohibited.
Don't try to disassemble, maintenance,
rebuild, or alter by yourself.
To disassemble creates therisk of fire and
electric shock.
If the dirt or dust from getting on the outlet,
that will creates the risk of electric shock by humidity.
Do not damage power cord and outlet.
Using multi-socket and household extension
cords can create the risk of fire by heating.
Do not touch socket with wet hands.
That creates the risk of electric shock and
injury.
Power plug must be plugged in completely
Do not use worn socket and loose plug.
If device fall into water, please unplug from
the electrical socket and stop using.
Please contact your original retailer or an
authorized service provider.
Do not use unqualified water.
Water without anti-bacteria process or
moving the hazard material out creates
the risk of ill. Qualified water supply is
recommended.
Keep using worn power cord or outlet
creates the risk of fire, electric shock,and
short circuit.
Positioning by brad nails.
Power cord was worn.
Rebuild or alter by yourself.
Twist or bend the power cord .
Pull on the power cord
Put heavy weight on power cord.
Bend power cord as loop
Please clean the dust or dirt over the outlet
periodically.
Avoid multi-socket and household extension
cords. Do not over voltage.
Do not drink the water which pH-value is over 10.
That will creates the risk of injury. The water
which pH-value is around 9.5 is recommended.
The third section of alkaline water is also
recommended.
strong alkaline water(PH10) and acid water.
Water from drainage pipe
Water from outlet during electrode cleaning
May cause uncomfortable feeling.
If pre-filter is installed and being absent
without producing electrolyzed alkaline
water more than 2 days, MUST turn off the
water inlet switch.
May cause water leakage and water pipe
burst because of high pressure.
Before the first appliance of each day,
please let the water flow freely about 0.
6 liter(about 15 seconds) and then begin
to use.
Using such containers will cause them to
discolor or to be worn.
Contact our service providers about
fees of the related maintenances.
The following persons should contact doctor
before using weak acid water.
Avoid using aluminium containers which
anti-alkali ability is weak. Avoid using
copper containers without anti-acid ability
For electrolyzed alkaline water or clean
water, please store it at clean closed
containers. Drink up in 1 day at normal
temperature. Drink up in 2 days for
storing at refrigerator.
As chlorine in water is removed, it's easy to
be addled to cause injury.
Do not use unqualified water.
Low skin resistance .
With over-sensitive skin.
For drinking electrolyzed alkaline water for
the first time, please drink 1 or 2 cups of the
first section of alkaline electrolyzed water
daily. After 2 weeks and body can accept
alkaline electrolyzed water, then drink the
second or the third section of alkaline
electrolyzed water.
To drink highly alkaline watermay cause
uncomfortable feeling.
Do not use hot water with the temperature
over 40 through pre-filters or device.
That may case the damage of filters and device.
In a hard-water area, electrodes cannot
function properly. Avoid being dysfunctional
and losing of water quality, please clean
and maintenance periodically.
Over two days.plpase let the water flow
freely about 8 liter (about 3 minutes) and
then begin to use.
If go out over one day or absent withant using water ioniter more than one day, must turn off power and water inlet switch.

Accessories
Before you use them, please match the accessories you have with the pictures below.
If there is any accessory missing, please ask your dealer for it.
Each kind of machine gets different kinds of accessories, please match and confirm.
Required Tools
Product Overview After Installment
45
The accessories for this machine.
Water Faucet Faucet Lock Trisection valve switch
Calcium powder additive bucket
Back Hanging Set
(used to stabilize the hanging
section at the back)
(additional purchase required)
Base Nut
Quartile hexagonal union tee
PH value measurement fluid
Soft hose clip
(x2)
150cm hard tube
Faucet washer
(33x51x2)
Plastic anchors x2
(additional purchase)
Stabilizing nails x2
(additional purchase)
2 3 4 51
Electric drill Cyclone drill heads
(35mm),
Slip Joint Pliers Phillips screwdrivers
Slotted screwdriver
Wrenches
Water fauce
(not included with the product)
acid water, water drain
signal passage line
electric socket
Open relief faucet Alkaline water exit
acid water pipe alkaline water pipe
water pipe Three-stages pre-filters
(purchased separately)
power line Mainframe
Product Components

Accessories
Before you use them, please match the accessories you have with the pictures below.
If there is any accessory missing, please ask your dealer for it.
Each kind of machine gets different kinds of accessories, please match and confirm.
Required Tools
Product Overview After Installment
45
The accessories for this machine.
Water Faucet Faucet Lock Trisection valve switch
Calcium powder additive bucket
Back Hanging Set
(used to stabilize the hanging
section at the back)
(additional purchase required)
Base Nut
Quartile hexagonal union tee
PH value measurement fluid
Soft hose clip
(x2)
150cm hard tube
Faucet washer
(33x51x2)
Plastic anchors x2
(additional purchase)
Stabilizing nails x2
(additional purchase)
2 3 4 51
Electric drill Cyclone drill heads
(35mm),
Slip Joint Pliers Phillips screwdrivers
Slotted screwdriver
Wrenches
Water fauce
(not included with the product)
acid water, water drain
signal passage line
electric socket
Open relief faucet Alkaline water exit
acid water pipe alkaline water pipe
water pipe Three-stages pre-filters
(purchased separately)
power line Mainframe
Product Components

67
Installment ExplanationInstallment Explanation
1.Turn the water off.
2.Connect the quartile hexagonal union tee and the trisection valve switch
together according to the correct order.
3.Cut the 150cm hard tube into suitable size, and then connect one end to the
mainframe(if a pre-filter is installed, the water entry point
should be installed first at the pre-filter) as the other end is connected to the
trisection valve switch.
The mainframe's
water entry point
150cm hard tube
1.Place the faucet and the washers into the drilled hole according to the required
sequence, and pull the water tubes and the signal passage line under the basin.
2.Put the base nut on the faucet lock and pull the water tubes and the signal passage line
through the faucet lock and lock it from the bottom to the top anticlockwise.
3.Clip the tube marked alkaline water to the alkaline water exit point on the machme.
4.Clip the tube marked acid water to the acid water exit point on the machine.
5.Connect the faucet signal passage line to the transfer hole of the machine.
6.Plug the power cord into the socket.
7.Turn the trisection valve switch on.
electric plug
soft hose clip
I. Hole-drilling For Faucet Installment
1.Select the area needed for the drill hole and mark it.
2.Use the handhold drill and install the 35mm cyclone drill head.
3.Proceed with drilling at the selected location
Hole size
II. The Connection Between The
Water Source And The Mainframe.
Quartile
hexagonal union tee
III. Faucet And Machine
signal passage line
acid water tube
alkaline water tube
faucet lock
base nut
faucet washers
Trisection valve switch
Procedures
Procedures
Procedures

67
Installment ExplanationInstallment Explanation
1.Turn the water off.
2.Connect the quartile hexagonal union tee and the trisection valve switch
together according to the correct order.
3.Cut the 150cm hard tube into suitable size, and then connect one end to the
mainframe(if a pre-filter is installed, the water entry point
should be installed first at the pre-filter) as the other end is connected to the
trisection valve switch.
The mainframe's
water entry point
150cm hard tube
1.Place the faucet and the washers into the drilled hole according to the required
sequence, and pull the water tubes and the signal passage line under the basin.
2.Put the base nut on the faucet lock and pull the water tubes and the signal passage line
through the faucet lock and lock it from the bottom to the top anticlockwise.
3.Clip the tube marked alkaline water to the alkaline water exit point on the machme.
4.Clip the tube marked acid water to the acid water exit point on the machine.
5.Connect the faucet signal passage line to the transfer hole of the machine.
6.Plug the power cord into the socket.
7.Turn the trisection valve switch on.
electric plug
soft hose clip
I. Hole-drilling For Faucet Installment
1.Select the area needed for the drill hole and mark it.
2.Use the handhold drill and install the 35mm cyclone drill head.
3.Proceed with drilling at the selected location
Hole size
II. The Connection Between The
Water Source And The Mainframe.
Quartile
hexagonal union tee
III. Faucet And Machine
signal passage line
acid water tube
alkaline water tube
faucet lock
base nut
faucet washers
Trisection valve switch
Procedures
Procedures
Procedures

9
The Instruction Of Measuring PH
Using The Tank For Calcium Powder
The Instruction Of Replacing Filters
The following is the m procedureeasuring
1. Find thedropping bottle of
PH indicator dyein accessory
package.
2. Let thegenerated water flows
freely for 10seconds
(for precise sampling).
3. Addsome sampled waterin the
test tube. Coverand mix well.
4. In abright environment, PH-valueis
determined visually byvisual
comparison with standardcolor charts.
Two dropsof the dye
is added toa test tube.
Do not splash in eyes, taste, or swallow
If swallowed. Drink water to dilute concen-
tration. If in eyes, flush eyes with plenty of
water. Seek medical aid immediately.
Must cover the bottle tightly. And put it in
aplace where children cannot reach.
PH indicator dye have a 1-year life cycle.
If necessary,
Please contact the nearest dealer.
Caution
The procedure of replacing filters
123465
1. Push the switch of filter cartridge.
2. Pull up the filter cartridge.
3. Wrench out the top cap of filters bottle.
4. Take out the filter.
5. Rotate the top cap anticlockwise to
remove filter.
6. Put a new filter and rotate clockwise to tighten.
7. Put the filter into the bottle and tighten the top cap.
8. Pull the switch of filter cartridge.
9. Reset the counter(Please refter to page 13
for the reset counter procedure.)
10. After flowing water freely for 1~2 minutes,
the device is ready.
Tips
1. The purposeof adding
calcium powder isfor
improving soft-water in
order to reachthe desired
pH-value.(In a hard-water
area, it's not
recommend to addthat.)
2. Before addingcalcium
powder, MUSTclean the
tank to preventfrom the
aggregate of powder. It
may cause dirtin water
or aggregate onthe
electrode.
1.
Rotate the top
cap of filter
bottle.
2.
The center hole
of the filter
(indicated by the
arrow) is the hole
to put the tank of
calcium powder
3.Find the tank of
calcium powder in
the accessory pack.
4.Put some calcium powder in
the tank (You can buy calcium
powder from drug store or
retailers).
6.
Tighten the
top cap.
5.
Put the tank
into the filter.
7.
Put filter into
filter bottle.
8.
It's done.
8
Instruction Of The Back Of Device
How To Mount The Device On Wall
Frame
Drainage hole
( To avoid the leak drain form this hole)
The foots of
the bottom
The back hole
Wall Nalls
Mark of the
specificaticn
Power cord
Inlet
The instruction of installation
1.Locate the holepositions of frameon the wall.
2.Drill the holeon the wall.
3.Put the plasticanchors in theholes.
4.Tighten the nails in bolts.
5.Put the deviceon the aluminumframe.
6.All procedures arefinished.
The back hole
for hanging purpose

9
The Instruction Of Measuring PH
Using The Tank For Calcium Powder
The Instruction Of Replacing Filters
The following is the m procedureeasuring
1. Find thedropping bottle of
PH indicator dyein accessory
package.
2. Let thegenerated water flows
freely for 10seconds
(for precise sampling).
3. Addsome sampled waterin the
test tube. Coverand mix well.
4. In abright environment, PH-valueis
determined visually byvisual
comparison with standardcolor charts.
Two dropsof the dye
is added toa test tube.
Do not splash in eyes, taste, or swallow
If swallowed. Drink water to dilute concen-
tration. If in eyes, flush eyes with plenty of
water. Seek medical aid immediately.
Must cover the bottle tightly. And put it in
aplace where children cannot reach.
PH indicator dye have a 1-year life cycle.
If necessary,
Please contact the nearest dealer.
Caution
The procedure of replacing filters
123465
1. Push the switch of filter cartridge.
2. Pull up the filter cartridge.
3. Wrench out the top cap of filters bottle.
4. Take out the filter.
5. Rotate the top cap anticlockwise to
remove filter.
6. Put a new filter and rotate clockwise to tighten.
7. Put the filter into the bottle and tighten the top cap.
8. Pull the switch of filter cartridge.
9. Reset the counter(Please refter to page 13
for the reset counter procedure.)
10. After flowing water freely for 1~2 minutes,
the device is ready.
Tips
1. The purposeof adding
calcium powder isfor
improving soft-water in
order to reachthe desired
pH-value.(In a hard-water
area, it's not
recommend to addthat.)
2. Before addingcalcium
powder, MUSTclean the
tank to preventfrom the
aggregate of powder. It
may cause dirtin water
or aggregate onthe
electrode.
1.
Rotate the top
cap of filter
bottle.
2.
The center hole
of the filter
(indicated by the
arrow) is the hole
to put the tank of
calcium powder
3.Find the tank of
calcium powder in
the accessory pack.
4.Put some calcium powder in
the tank (You can buy calcium
powder from drug store or
retailers).
6.
Tighten the
top cap.
5.
Put the tank
into the filter.
7.
Put filter into
filter bottle.
8.
It's done.
8
Instruction Of The Back Of Device
How To Mount The Device On Wall
Frame
Drainage hole
( To avoid the leak drain form this hole)
The foots of
the bottom
The back hole
Wall Nalls
Mark of the
specificaticn
Power cord
Inlet
The instruction of installation
1.Locate the holepositions of frameon the wall.
2.Drill the holeon the wall.
3.Put the plasticanchors in theholes.
4.Tighten the nails in bolts.
5.Put the deviceon the aluminumframe.
6.All procedures arefinished.
The back hole
for hanging purpose

10 11
VS-30/50/70 Functions
Operation Guidelines
1.When you are going to obtain drinking water, please press the water on/off button.
At this time the water indication light will turn "purple". Then you are
able to get water when the light turns"blue."'
2.When you are intending to turn the water off, press the water on/off button to shut
the water off. At the same time the power light will turn red, and be on hold.
3.When you turn on the water each time, (if the water quality is not lock) the water
quality level will be set at " standard alkaline ". If you wish to adjust the water
quality level, you can press the"+ -"button to select your desired water quality
level then press the "confirm" button to get the water.
4.Every time when you finish using the equipment, the liquid crystal display
will continue to be on for 60 seconds. Then it will enter the sleep (electric saving)
mode after 60 seconds and the screen will go blank.
VS-30/50/70 Functional Directions
PH Value Micro Adjustment Express
Button Operation Guidelines.
Function direction
This function can micro adjust the PH value in the water. For example: If your
water quality level is set at " standard alkaline " and the default setting of
the machine is at PH9.5 while you wish to increase or reduce the value, you
can use the express button to adjust the PH value to micro adjust the water
quality. There are ten levels of PH micro adjustment to increase or decrease
from 0.1~0.5.
Operation direction
1.Press the water on/off button to eject water. Then wait until the water
indicator light is on "blue"to press the "function" button to enter the menu.
2.Press the "+-" button to select the "PH set" screen.
3.Please press the "confirm" button again to use the "+-" button to increase
or decrease the PH value.
4.After micro adjust the PH value you desired, then press the "confirm" button
to complete the setting.
Using The Control Panel
"+" increase forPH value/
PH value microadjustment/
time, language andvoice, etc
Menu
The instruction of alkaline water
Alkaline water
PH-value
The pH-value mentioned in the table may vary depend on different water quality and
different water pressure.
Standard
alkaline
Mid
alkaline
Low
alkaline
It's for daily drinking and also good for chronic
disease to improve the uncomfortable feeling
about stomach, constipation, diarrhea, and
gout and prevent from aging.
It's good for people used to drink alkaline
electrolyzed water and also good for people of
35~45 years old.
The taste is more abundant for tea or coffee
brewing.
And improve the uncomfortable feeling of the
tiredness and shortage of sleep.
It's for people to drink for the first time. It's
also good for people of 20~35 years old.
To balance of acid and alkaline and
prevent from aging.
High
electrolyzed
Over 10
About 9.0~9.5
About 8.5~9.0
About 8.0~8.5
Fruit cleaning remove insecticides.
Dishes cleaning remove oil sludge
Clothes cleaning remove stains on the collars
Filtering
water
Clean water
It's for preparing milkor taking
medicine.
Low acid
Acid water
Usage
It's for deep cleaning
beneath the skin's
surface and deep
pore cleaning.
About
5.0~5.5
PH-value
About
2.9~4.0
About 9.5~9.7
Usage
Confirm button
High
alkaline
Remove the odor of kelp and burdock.
Rice and vegetables are more delicious.
The outlet ofalkaline water
The outlet ofacid water
LCD display
Power
(Water on/offbutton)
It's anti-bacteria for floor
cleaning, dishes cleaning.
High acid
"+" decrease forPH value/
PH value microadjustment/
time, language andvoice, etc
(Under the circumstances of waterbeing available)

10 11
VS-30/50/70 Functions
Operation Guidelines
1.When you are going to obtain drinking water, please press the water on/off button.
At this time the water indication light will turn "purple". Then you are
able to get water when the light turns"blue."'
2.When you are intending to turn the water off, press the water on/off button to shut
the water off. At the same time the power light will turn red, and be on hold.
3.When you turn on the water each time, (if the water quality is not lock) the water
quality level will be set at " standard alkaline ". If you wish to adjust the water
quality level, you can press the"+ -"button to select your desired water quality
level then press the "confirm" button to get the water.
4.Every time when you finish using the equipment, the liquid crystal display
will continue to be on for 60 seconds. Then it will enter the sleep (electric saving)
mode after 60 seconds and the screen will go blank.
VS-30/50/70 Functional Directions
PH Value Micro Adjustment Express
Button Operation Guidelines.
Function direction
This function can micro adjust the PH value in the water. For example: If your
water quality level is set at " standard alkaline " and the default setting of
the machine is at PH9.5 while you wish to increase or reduce the value, you
can use the express button to adjust the PH value to micro adjust the water
quality. There are ten levels of PH micro adjustment to increase or decrease
from 0.1~0.5.
Operation direction
1.Press the water on/off button to eject water. Then wait until the water
indicator light is on "blue"to press the "function" button to enter the menu.
2.Press the "+-" button to select the "PH set" screen.
3.Please press the "confirm" button again to use the "+-" button to increase
or decrease the PH value.
4.After micro adjust the PH value you desired, then press the "confirm" button
to complete the setting.
Using The Control Panel
"+" increase forPH value/
PH value microadjustment/
time, language andvoice, etc
Menu
The instruction of alkaline water
Alkaline water
PH-value
The pH-value mentioned in the table may vary depend on different water quality and
different water pressure.
Standard
alkaline
Mid
alkaline
Low
alkaline
It's for daily drinking and also good for chronic
disease to improve the uncomfortable feeling
about stomach, constipation, diarrhea, and
gout and prevent from aging.
It's good for people used to drink alkaline
electrolyzed water and also good for people of
35~45 years old.
The taste is more abundant for tea or coffee
brewing.
And improve the uncomfortable feeling of the
tiredness and shortage of sleep.
It's for people to drink for the first time. It's
also good for people of 20~35 years old.
To balance of acid and alkaline and
prevent from aging.
High
electrolyzed
Over 10
About 9.0~9.5
About 8.5~9.0
About 8.0~8.5
Fruit cleaning remove insecticides.
Dishes cleaning remove oil sludge
Clothes cleaning remove stains on the collars
Filtering
water
Clean water
It's for preparing milkor taking
medicine.
Low acid
Acid water
Usage
It's for deep cleaning
beneath the skin's
surface and deep
pore cleaning.
About
5.0~5.5
PH-value
About
2.9~4.0
About 9.5~9.7
Usage
Confirm button
High
alkaline
Remove the odor of kelp and burdock.
Rice and vegetables are more delicious.
The outlet ofalkaline water
The outlet ofacid water
LCD display
Power
(Water on/offbutton)
It's anti-bacteria for floor
cleaning, dishes cleaning.
High acid
"+" decrease forPH value/
PH value microadjustment/
time, language andvoice, etc
(Under the circumstances of waterbeing available)

12 13
Vs-30/50/70 Functions
Adjustable Functions Throngh LCD Touchable Panel
Liquid Crystal Display Adjustable Function Items Default Setting
Time
Lock
PH set
Filter reset
Volume set
Language option
Voice assistant
Exit
00:00
disengaged
English
English
Display the adjustabletime and number
Able to lockonto your desiredwater quality
Able to adjustthe PH waterquality to suit your needs
1.(+) increase 0.1~0.5 2(-) decrease 0.1~0.5
Reset the filtercount to zero.
Adjust the Volume. (+) increase(-) decrease.
Select (Chinese, SimplifiedChinese, English)
Select ( Chinese,English, Music)
Exit the functionsetting
VS-30/50/70 Functions
Water Quality Express Button Operation Guidelines
1. Locking the water quality:
After pressing the water on/off button, wait until the water indication light turns
"blue" then press on the "confirm" button for 2 seconds. After that, the word LOCK
will appear on the upper right corner of the LCD for confirming the lock on the
water quality.
2. Disengage water quality lock:
When the water is running, and when the water indication light is on "blue,"
continue to press on the "confirm" button for 2 seconds. The LOCK on the LCD
will disappear, and the water lock is disengaged.
I.Water Quality Lock Express Button Operation
1. Locking the water quality.
A. Press the water on/off button and wait until the power indication light turns
"blue," and then press on the "MENU" button to enter the menu.
B. Press the "+-" button to select the LOCK Option.
C. Press the "confirm" button again to complete the lock of the water quality.
2. Disengage lock option:
A. When the water is running, and the power indication light is "blue," press the
"menu" button to enter the menu.
B. Press the "+-" button to select the "LOCK" Option.
C. Press on "confirm" again to disengage the LOCK option.
II.Water Quality Lock Express Button Operation
Functional directions
The "Lock" function can hold the water quality level you desired. For example :
If you want to drink "mid alkaline" water for a long period of time, after you apply
the LOCK function, you are able to get "mid alkaline" quality of water every time
you turn on the faucet. This function can prevent seniors or children from drinking
the water at a dangerous level.
Operation directions (Under the circumstances of waterbeing available)

12 13
Vs-30/50/70 Functions
Adjustable Functions Throngh LCD Touchable Panel
Liquid Crystal Display Adjustable Function Items Default Setting
Time
Lock
PH set
Filter reset
Volume set
Language option
Voice assistant
Exit
00:00
disengaged
English
English
Display the adjustabletime and number
Able to lockonto your desiredwater quality
Able to adjustthe PH waterquality to suit your needs
1.(+) increase 0.1~0.5 2(-) decrease 0.1~0.5
Reset the filtercount to zero.
Adjust the Volume. (+) increase(-) decrease.
Select (Chinese, SimplifiedChinese, English)
Select ( Chinese,English, Music)
Exit the functionsetting
VS-30/50/70 Functions
Water Quality Express Button Operation Guidelines
1. Locking the water quality:
After pressing the water on/off button, wait until the water indication light turns
"blue" then press on the "confirm" button for 2 seconds. After that, the word LOCK
will appear on the upper right corner of the LCD for confirming the lock on the
water quality.
2. Disengage water quality lock:
When the water is running, and when the water indication light is on "blue,"
continue to press on the "confirm" button for 2 seconds. The LOCK on the LCD
will disappear, and the water lock is disengaged.
I.Water Quality Lock Express Button Operation
1. Locking the water quality.
A. Press the water on/off button and wait until the power indication light turns
"blue," and then press on the "MENU" button to enter the menu.
B. Press the "+-" button to select the LOCK Option.
C. Press the "confirm" button again to complete the lock of the water quality.
2. Disengage lock option:
A. When the water is running, and the power indication light is "blue," press the
"menu" button to enter the menu.
B. Press the "+-" button to select the "LOCK" Option.
C. Press on "confirm" again to disengage the LOCK option.
II.Water Quality Lock Express Button Operation
Functional directions
The "Lock" function can hold the water quality level you desired. For example :
If you want to drink "mid alkaline" water for a long period of time, after you apply
the LOCK function, you are able to get "mid alkaline" quality of water every time
you turn on the faucet. This function can prevent seniors or children from drinking
the water at a dangerous level.
Operation directions (Under the circumstances of waterbeing available)

14 15
VS-30/50/70 LCD Functions Guideline
Liquid Crystal Display
Filter reset Volume set
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
waiting screen waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Automatically turned off
after 60 seconds
(energy saving mode).
PH set
Example
The water quality is set at "alkaline 3"
and wishing to adjust the PH level
from 9.5 to 9.8.
Time
PH set
Standard
alkaline
PH
Example
For wanting to reset the filter
counter to zero
Example
For wanting to adjust the volume
Time Time
Filter reset Volume set
Confirm
Return immediately tothe
waiting screen shownbelow:
return to waitingscreen
after 3 seconds.
select level?
9.5
PH 9.8
return immediately tothe
waiting screen shownbelow
and the standard alkaline's
PH level will belocked as 9.8
(+) increase (-) decrease
Volume set
VS-30/50/70 LCD Functions Guideline
Operation Guideline
1
2
3
4
. Press "MENU"
button to enter.
. Press "+-"button to
adjust the setting
and press the"confirm"
button to complete.
. Press "+-"button to
adjust the settingand
press the "confirm"
button to complete
. Press "+-"buttonto
get to theexit and
press the "confirm"
button to exitor wait
for 5 secondsand it will
exit automatically.
Setting items
operating without
connecting water
Liquid Crystal Display
Time
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Lock
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Example
for setting the time to 15:58
Time
Time
15:00
adjust the hourwhen
the hour isblinking.
5:58
adjust the minutes
when the minutes
section is blinking.
Time
Time will returnto
waiting screen after
3 seconds.
Example
wanting to set the lock on the
water quality
Time
Lock
Low alkaline
select level?
Return to thewaiting
screen and theword LOCK
is displayed onthe top right
corner of thescreen.
Lock

14 15
VS-30/50/70 LCD Functions Guideline
Liquid Crystal Display
Filter reset Volume set
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
waiting screen waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Automatically turned off
after 60 seconds
(energy saving mode).
PH set
Example
The water quality is set at "alkaline 3"
and wishing to adjust the PH level
from 9.5 to 9.8.
Time
PH set
Standard
alkaline
PH
Example
For wanting to reset the filter
counter to zero
Example
For wanting to adjust the volume
Time Time
Filter reset Volume set
Confirm
Return immediately tothe
waiting screen shownbelow:
return to waitingscreen
after 3 seconds.
select level?
9.5
PH 9.8
return immediately tothe
waiting screen shownbelow
and the standard alkaline's
PH level will belocked as 9.8
(+) increase (-) decrease
Volume set
VS-30/50/70 LCD Functions Guideline
Operation Guideline
1
2
3
4
. Press "MENU"
button to enter.
. Press "+-"button to
adjust the setting
and press the"confirm"
button to complete.
. Press "+-"button to
adjust the settingand
press the "confirm"
button to complete
. Press "+-"buttonto
get to theexit and
press the "confirm"
button to exitor wait
for 5 secondsand it will
exit automatically.
Setting items
operating without
connecting water
Liquid Crystal Display
Time
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Lock
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Example
for setting the time to 15:58
Time
Time
15:00
adjust the hourwhen
the hour isblinking.
5:58
adjust the minutes
when the minutes
section is blinking.
Time
Time will returnto
waiting screen after
3 seconds.
Example
wanting to set the lock on the
water quality
Time
Lock
Low alkaline
select level?
Return to thewaiting
screen and theword LOCK
is displayed onthe top right
corner of thescreen.
Lock

16 17
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Exit
Example
For wanting toexit the setting
Time
Exit
return immediately tothe
waiting screen shownbelow
VS-30/50/70 LCD Functions Guideline
1
2
3
4
. Press "menu"
button to enter.
. Press "+-"button to
adjust the settingand
press the "confirm"
button to complete.
. Press "+-"button to
adjust the settingand
press the "confirm"
button to complete
. Press "+-"buttonto
get to theexit and press
the "confirm" button
to exit orwait for 5
seconds and itwill exit
automatically.
Operation items
operating without
connecting water
Language
option
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Voice
assistant
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Example
for wanting toset the language
to "English"
Time
Language
option
Traditional Chinese
English
Simplified Chinese
Language
option
return immediately tothe
waiting screen shownbelow
after 3 seconds.
Example
For wanting toset the voiceto music
Time
Voice
assistant
Chinese
English
Music
Voice
assistant
return immediately tothe
waiting screen shownbelow
after 3 seconds.
Only available musicon vs7O
VS-30/50/70 LCD Functions Guideline
Liquid Crystal Display
Operation Guideline Liquid Crystal Display Liquid Crystal Display

16 17
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Exit
Example
For wanting toexit the setting
Time
Exit
return immediately tothe
waiting screen shownbelow
VS-30/50/70 LCD Functions Guideline
1
2
3
4
. Press "menu"
button to enter.
. Press "+-"button to
adjust the settingand
press the "confirm"
button to complete.
. Press "+-"button to
adjust the settingand
press the "confirm"
button to complete
. Press "+-"buttonto
get to theexit and press
the "confirm" button
to exit orwait for 5
seconds and itwill exit
automatically.
Operation items
operating without
connecting water
Language
option
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Voice
assistant
waiting screen
Automatically turned off
after 60 seconds
(energy saving mode).
Example
for wanting toset the language
to "English"
Time
Language
option
Traditional Chinese
English
Simplified Chinese
Language
option
return immediately tothe
waiting screen shownbelow
after 3 seconds.
Example
For wanting toset the voiceto music
Time
Voice
assistant
Chinese
English
Music
Voice
assistant
return immediately tothe
waiting screen shownbelow
after 3 seconds.
Only available musicon vs7O
VS-30/50/70 LCD Functions Guideline
Liquid Crystal Display
Operation Guideline Liquid Crystal Display Liquid Crystal Display

displaying to activation displaying to activation displaying to activation displaying to activation
cycles every2seconds cycles every2seconds cycles every2seconds cycles every2seconds
18 19
VS-30/50/70 LCD Display Directions
15 58
10.0 9.5 9.0 8.5
15 58 15 58 15 58
the PH value, filter lifespan value are simulation displays.
High
alkaline
Alkaline 4
preparation image
Preparing
Standard
alkaline Mid alkaline Low alkaline
preparation image
Preparing
preparation image
Preparing
preparation image
Preparing
preparation image preparation image preparation image preparation image
waiting screen waiting screen waiting screen waiting screen
display 5 seconds.
Alkaline 3 Alkaline 2 Alkaline 1
preparation image daily drinking Cooking early stage drinking
Filter
lifespan
display 5 seconds. display 5 seconds. display 5 seconds.
Filter
lifespan
Filter
lifespan
Filter
lifespan
ElectrolyzingElectrolyzingElectrolyzing ElectrolyzingElectrolyzingElectrolyzing ElectrolyzingElectrolyzingElectrolyzing ElectrolyzingElectrolyzingElectrolyzing
Alkaline 4Alkaline 4 Alkaline 3Alkaline 3 Alkaline 2Alkaline 2 Alkaline 1Alkaline 1
VS-30/50/70 LCD Display Directions
startup image Scenic View water quality
level display
water quality
level picture
Standard
alkaline
Standard
alkaline
Standard
alkaline
Drinking waterDrinking waterDrinking water
9.59.59.5
PHPHPH
Filter
lifetime
Filter
lifetime
Filter
lifetime
PH value display Filter lifetime display time display
Water cell Complete
Electrolytic Tank
Sequence Cycle
animation
(changes every second)
time display
Please refer topage 11 for the procedures of selfclean the electrodeplate.
Water cell
Return to waitingscreen when itis complete.
Water Quality Level And Screen Display Guidelines
LCD Display Directions
Star-up images
Electrode plate self cleaning