OptiPure QT-2+ Instruction manual
Installation, Operation & Maintenance Manual
For OptiPure FX Series Systems
Models: QT-2+, QTI-2+, QTC-2+, QTCI-2+
NOTICE TO INSTALLER:
DO NOT DISCARD THIS MANUAL AFTER INSTALLATION. THIS MANUAL CONTAINS IMPORTANT
OPERATION, MAINTENANCE AND PRECAUTIONARY INFORMATION. PLEASE PRESENT THIS MANUAL
TO USER/OPERATOR/OWNER AFTER INSTALLATION.
IT IS STRONGLY ENCOURAGED THAT YOU READ THIS MANUAL BEFORE INSTALLING SYSTEM TO
ENSURE THE BEST POSSIBLE INSTALLATION.
INSTALLATION MUST CONFORM TO ALL LOCAL AND STATE PLUMBING CODES AND REGULATIONS.
CONNECT SYSTEM TO COLD WATER SUPPLY ONLY. WATER TEMP. CAN NOT EXCEED 100°F/28°C.
DO NOT USE WITH WATER THAT IS MICROBIOLOGICALLY UNSAFE OR OF UNKNOWN QUALITY
WITHOUT ADEQUATE DISINFECTION BEFORE OR AFTER THE SYSTEM. SYSTEMS CERTIFIED FOR
CYST REDUCTION MAY BE USED ON DISINFECTED WATER THAT MAY CONTAIN FILTERABLE CYSTS.
NOTICE TO USER/OPERATOR/OWNER:
PLEASE COMPLETE THE PRODUCT REGISTRATION CARD AND MAIL OR FAX TO MANUFAC-
TURER. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE FOR PARTS, MAINTENANCE OR
TROUBLE-SHOOTING.
IT IS RECOMMENDED THAT ALL PERSONNEL RESPONSIBLE FOR OPERATION AND MAINTENANCE
OF THIS PRODUCT READ THE PRECAUTIONS, OPERATION AND MAINTENANCE SECTIONS OF THIS
MANUAL.
Introduction
Please refer to this manual when performing routine lter changes. The instructions make periodic maintenance
quick and easy, and ensure you will receive maximum benet from your system.
System Specications
Maximum Pressure: 125 psi/8.6 bar Maximum Temperature: 100°F/38°C, Min.: 35°F/2°C
Inlet/Outlet Connections: 3/8” fnpt Service Flow Rate: 4.5 gpm /17 lpm
Capacity: Change filters at gallon rating or at least every 6 months, or when pressure gauge needle enters the red zone on the
outlet gauge while water is flowing through the filter system under normal operating conditions.
Gallon Rating: QT-2+, QTI-2+: 45,000 gals./170,325 ltrs. QTC-2+, QTCI-2+: 54,000 gals./204,390 ltrs.
QT-2+iom104
Foodservice Filtration Systems
1
2
Installation Precautions
NOT
NOT
NOT
NOT
NOT
NOT
NOT
ALLOW
IF
NOT
Always
NOT
Installation Procedure (See Installation Drawings for Detail)
NOTE: DO NOT OVERTIGHTEN CONNECTION FITTING INTO BALL VALVE.
NOTE: NO ACTIVATION IS REQUIRED FOR THE OPTIPURE SYSTEM TO PERFORM
PROPERLY. FLUSHING IS RECOMMENDED TO ALLOW AIR TO ESCAPE THE SYSTEM AND REMOVE
ANY CARBON FINES PRIOR TO CONNECTING TO EQUIPMENT.
2
Installation Drawings & Dimensions
3
S5-20 XTO-Q
XTO-Q
S5-20 XTO-Q XTO-Q
INLET
Direction of Flow
OUTLET
4
Maintenance
Filter Change Frequency
Filter Cartridge Replacement Procedure
Operation
1
3
4
5
6
7
4
Replacement Parts for: QT-2+, QTC-2+, QTI-2+, QTCI-2+
Dwg ID # Part # Description
1 300-05899 Head, Qwik-Twist - 3/8” I/O
2 300-05830 CTO-Q Replacement Cartridge - QT-2+
300-05835 CTOS-Q Replacement Cartridge - QTI-2+
300-05840 XTO-Q Replacement Cartridge - QTC-2+
300-05845 XTOS-Q Replacement Cartridge - QTCI-2+
3 600-10043 Housing, 20”
4 252-10120 Prelter, 5m
5 590-01020 Bracket, SS
6 520-12215 Valve, 3/8” Inlet Ball
7 520-12218 Flush Valve
8 550-65306 Elbow
9 550-65404 Tee
10 550-88105 Nipple, 3/8”
11 550-88130 Nipple, 3/8”
12 550-80803 Elbow, 3/8”
13 550-83952 Bushing 3/8” x1/4”
14 530-20019 Gauge, Pressure 0-160 psi
15 550-80503 Tee, 3/8”
16 580-00050 Hose, Reinforced Beverage
17 800-05011 Clamp
18 800-00223 Screw
19 800-00190 Washer
FilterXpress div. of Procam Controls, Inc.
2605 Technology Dr. Bldg. 300
Plano, TX 75074 USA
P: 972.881.9797 F: 972.422.6262
email: procam@lterxpress.com
©2004 Procam Controls, Inc. QT2+iom104
Replacement Filter Cartridges
5
Models QT-2+ and QTI-2+ Tested and Certi-
ed by NSF International against NSF/ANSI
Standard 42 for the reduction of:
Standard 42: Aesthetic Effects
Chlorine Reduction
Taste and Odor Reduction
Particulate Reduction Class I
Models QTC-2+ and QTCI-3+ Tested and
Certied by NSF Internatio2al against NSF/
ANSI Standard 42 and 53 for the reduction of:
Standard 42: Aesthetic Effects
Chlorine Reduction
Taste and Odor Reduction
Standard 53: Health Effects
Cyst Reduction
Turbidity Reduction
NOTE: Testing was performed under standard laboratory condi-
tions, actual performance may vary. It is recommended that you
have your water supply tested to determine your actual water
treatment requirements.
This manual suits for next models
3
Table of contents
Other OptiPure Water Filtration System manuals
OptiPure
OptiPure ScaleX2 SX2-21 Instruction manual
OptiPure
OptiPure OPS175 User manual
OptiPure
OptiPure FX-21 Owner's manual
OptiPure
OptiPure QT10-2 Instruction manual
OptiPure
OptiPure BWS1500 Instruction manual
OptiPure
OptiPure ScaleX2 SX2-21 Instruction manual
OptiPure
OptiPure QT Series Instruction manual
OptiPure
OptiPure OPS70CR User manual
OptiPure
OptiPure ScaleX2 SX2-11 Instruction manual
OptiPure
OptiPure QT-Multi-Point Manifold Series Instruction manual
Popular Water Filtration System manuals by other brands
Perfect Water Technologies
Perfect Water Technologies Tap Master Jr Series Installation & service manual
LG
LG WHD71RW4RP owner's manual
Laica
Laica Fast Disk FD03A Instructions and warranty
Cuckoo
Cuckoo CP-QN1401SW/WHCBMYCI user manual
VEVOR
VEVOR CPF-2500 instruction manual
LifeSource
LifeSource Premier Series owner's guide
BWT
BWT bestaqua 14ROC Installation and operating instructions
Aqua PRO
Aqua PRO AP-600W-A5-GST2 manual
Culligan
Culligan RVF-10 Installation and operation instructions
Master
Master MBA-MM-1040 Installation and operation manual
ubbink
ubbink BioPressure 3000 manual
IONFILTER
IONFILTER Filtermax Basic user manual