Char-Griller 2121 User manual

OM2121 C.1 ™ & © Char-Griller / A&J Mfg.
Owners Manual Model #2121
Charcoal Grill
Super Pro™
Keep your receipt with this manual for Warranty.
600033

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 2
STOP! CALL FIRST! DO NOT RETURN PRODUCT TO STORE.
CALL [phone] This product has been built to the highest quality standards.
Call us should you have any questions not addressed in these instructions, or for
service information.
Have your grills serial number (located on the back of the grill body or on the leg)
when calling.
No Returns on
Used Grills

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 3
(Tools Not Included)
Pliers and 7/16" nut driver
ITEM QTY DESCRIPTION PART NO.
1 1 HOOD 201079
2 1 WARMING RACK 301042
3 4 COOKING GRATE 100049
4 2 ASH PAN HANGERS 200024
5 1 ASH PAN 200048
6 1 GRILL BODY 900131
7 1 FILLER PLATE 100054
8 1 DAMPER CIRCLE 100036
9 2 LEG BRACE 100051
10 2 SHORT LEG 100056
11 1 WIRE SHELF 200050
12 2 LEG CAP 550013
13 2 LONG LEG 100055
14 2 HUB CAP 550007
15 2 WHEEL 550003
16 1 AXLE 100057
17 2 FRONT SHELF SUPPORTS 100053
18 2 FRONT SHELF BRACKETS 100052
19 2 FRONT SHELF SLAT 100050
20 3 UTENSIL HOOK 500003
21 1 SIDE SHELF 300016
22 1 STACK 300015
23 1 HOOD HANDLE 550014
24 1 LOGO PLATE 101383
25 1 BEZEL, THERMOMETER 101360
26 1 THERMOMETER 301076
27 1 GRATE LIFTER 10-0045

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 4
Page Intentionally Left Blank For Notes

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 5
ASSEMBLY INSTRUCTIONS
Read all safety warnings and instructions carefully before
assembling and operating your grill.
IMPORTANT HINT: DO NOT TIGHTEN ANY NUTS AND BOLTS UNTIL
GRILL IS FULLY ASSEMBLED.
Step 1: Assemble Long Legs, Short Legs, and Leg Braces as show below then secure the Leg
Braces to one set of Long Leg and Short Leg with 4 Hex Bolts and 4 Hex Nuts.
Long Legs
Short Legs
Leg Braces
Hex Nuts
Hex Bolts
Hex Bolts
Step 2: Install Bottom Wire Shelf by placing the four corner hooks inside the hole on each leg
then rotate the leg assemblies up and secure the Leg Braces to the other side of the Long Leg
and Short Leg set.
Hex Bolts
Bottom Wire Shelf Hex Bolts
Leg Braces
Hex Bolts

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 6
Step 3: Lay the cart assembly down with the Long Legs on the floor then install the Wheels and
Wheel Axle. On one end of the Axle insert the Cotter Pin into the hole on the Axle and snap in
the Hub Cap. Slide one Flat Washer and one Wheel onto the Axle then slide the Axle through
the holes on the Short Legs and Bottom Shelf. Complete the assembly by sliding the other
Wheel and Flat Washer onto Axle then insert the Cotter Pin and snap on the Hub Cap.
Step 4: Attach the Grill Body to the previous assembly cart using four 1 3/4” Hex Bolts and four
Hex Nuts. The Bolts must go through the leg, Grill Body then tighten with the Hex Nuts inside
the Grill body.
Wheel Axle
Wheels
Cotter Pin
Hub Cap
Hub Cap
Hex Nuts
Hex Bolts
Hex Bolts

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 7
Step 5: Attach Damper Circle to the side of the Grill Body with one Hex Bolts, two Flat Washers,
one Lock Washer, and one Hex Nut.
Flat Washers
Damper Circle
Hex Bolt
Lock Washer
Hex Nut
Step 6: Attach the Grill Hood to the Grill Body using the two Hinge Pins and two Cotter Pins
provided.
Hinge Pin
Hinge Pin
Grill Hood
Grill Body
Cotter Pins

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 8
Step 7: Insert Thermometer through hole in Bezel and Grill Hood (from outside) and secure with
Wing Nut. Then attach Hood Handle to the Grill Hood with two 3/4" hex bolts, two lock washers,
and two hex nuts. See below.
Thermometer
Wing Nut
Hood Handle
Hex Bolts
Hex Nuts
Grill Hood
Step 8: Insert Smokestack Assembly through the hole on the Grill Hood from the inside of the
Grill Hood then secure it with two Hex Bolts and two Hex Nuts.
Lock Washers
Hex Bolts
Smokestack Hex Nuts
Grill Hood
Bezel

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 9
Step 9: Attach Side Shelf to Grill Body with four Hex Bolts and four Hex Nuts.
Hex Bolts
Hex Nuts
Side Shelf
Grill Body
Step 10: Attach Front Shelf to Grill Body with four Hex Bolts and four Hex Nuts.
Hex Bolts
Hex Nuts
Front Shelf
Hex Bolts

OM2121 C.1 ™ & © Char-Griller / A&J Mfg. 10
Step 11: To install the Warming Rack first attach the four 1 3/4” Hex Bolts and four Hex Nuts
onto the Grill Body and Grill Hood. Then Position the Warming Rack onto the Hex Bolts and
Secure it with two more Hex Nuts.
Hex Nuts
Hex Bolts
Hex Bolts
Hex Nuts
Step 12: Place Ash Pan and Ash Pan Hangers onto Grill Body.
Ash Pan Hangers
Ash Pan
Grill Body