Chauvet EVE E-100Z User manual

User Manual V3

TABLE OF CONTENTS
EVE E-100Z V3 User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin....................................................................... 1
What Is Included ........................................................................................... 1
Unpacking Instructions.................................................................................. 1
Claims................................................................................................................ 1
Text Conventions.......................................................................................... 1
Symbols ........................................................................................................ 1
Disclaimer ..................................................................................................... 1
Product at a Glance ...................................................................................... 2
Safety Notes.................................................................................................. 2
2. Introduction ................................................................................ 3
Product Overview.......................................................................................... 3
Product Dimensions...................................................................................... 4
3. Setup ........................................................................................... 5
AC Power...................................................................................................... 5
Fuse Replacement............................................................................................. 5
Power Linking..................................................................................................... 5
Mounting ....................................................................................................... 6
Orientation.......................................................................................................... 6
Rigging............................................................................................................... 6
4. Operation .................................................................................... 7
Control Panel Operation................................................................................ 7
Menu Map..................................................................................................... 7
Configuration (DMX) ..................................................................................... 7
Starting Address................................................................................................. 7
D-Fi USB Connectivity .................................................................................. 7
Configuration (D-Fi USB) ................................................................................... 8
D-Fi USB DIP Switch Channels............................................................................... 8
DMX Channel Assignments and Values....................................................... 9
3-CH................................................................................................................... 9
1-CH................................................................................................................... 9
Configuration (Standalone)........................................................................... 9
Dimmer............................................................................................................... 9
Strobe................................................................................................................. 9
Dimmer Speed Mode ......................................................................................... 9
Fan Mode........................................................................................................... 9
Master/Slave Mode (Wired) .......................................................................... 10
Master/Slave Mode (D-Fi USB)..................................................................... 10
5. Maintenance................................................................................ 11
Product Maintenance.................................................................................... 11
6. Technical Specifications ........................................................... 12
Returns............................................................................................ 13
Contact Us ...................................................................................... 14

Page 1 of 14
EVE E-100Z V3 User Manual Rev. 1
BEFORE YOU BEGIN
1. BEFORE YOU BEGIN
What Is Included
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Symbols
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetdj.com.
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2016 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States ofAmerica.
CHAUVET, the Chauvet logo, D-Fi USB, and EVE E-100Z V3 are registered trademarks or trademarks of
Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other
company and product names and logos referred to herein may be trademarks of their respective
companies.
• EVE E-100Z V3
•GelFrame
• Framing Shutters
• Glass Gobo Holder
• Steel Gobo Holder
• Seetronic Powerkon Power Cord
• Warranty Card
• Quick Reference Guide
CONVENTION MEANING
1–512 Arange of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
SYMBOL MEANING
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.

Page 2 of 14
BEFORE YOU BEGIN
EVE E-100Z V3 User Manual Rev. 1
Product at a Glance
Safety Notes
Use on Dimmer Auto Programs 
Outdoor Use Auto-ranging Power Supply 
Sound-Active Replaceable Fuse 
DMX User-Serviceable 
Master/Slave 
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing the
fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a safety cable.
• Make sure there are no flammable materials close to the product when operating.
• Do not touch the product’s housing when operating because it may be very hot.
• Always make sure that the voltage of the outlet to which you are connecting the product is
within the range stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20)To prevent risk of fire or shock, do not expose the
product to rain or moisture.
• Alwaysinstall theproduct in a location with adequate ventilation,at least 20 in (50 cm) from
adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part.Always use the hanging/
mounting bracket.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at
higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to damage
or malfunction. Please contact the nearest authorized technical assistance center.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be sure that
they also receive this document.

Page 3 of 14
EVE E-100Z V3 User Manual Rev. 1
INTRODUCTION
2. INTRODUCTION
Product Overview
WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so
may cause damage to the product.
Focus Knob
Zoom Knob
DMX
In/Out
Fuse Holder
Power In
Gel Frame
Framing Shutter x4
Menu Buttons
Power Out
LED Display
Gel Frame
Holder
D-Fi USB Port
Gobo Holder
Thumbscrew
Safety
Loop

Page 4 of 14
INTRODUCTION
EVE E-100Z V3 User Manual Rev. 1
Product Dimensions
16.9 in
430 mm
24 in
611 mm
7.2 in
183 mm

Page 5 of 14
EVE E-100Z V3 User Manual Rev. 1
SETUP
3. SETUP
AC Power
The EVE E-100Z V3 an auto-ranging power supply and it can work with an input voltage range of 100 to
240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s
specifications chart. The listed current rating indicates the product’s average current draw under normal
conditions.
Fuse Replacement
Power Linking
The product provides power linking via the Edison outlet located in the back of the product. Please see the
diagram below for further explanation.
Power Linking Diagram
• Always connect the product to a protected circuit (a circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
• To eliminate unnecessary wear and improve itslifespan, during periods ofnon-
use completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
1. Disconnect the product from power.
2. Using a flat-head screwdriver, loosen the fuse holder and pull straight out.
3. Remove the blown fuse from the holder.
4. Replace with a fuse of the exact same type and rating.
5. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
You can power link up to 9 EVE E-100Z V3 products on 120 VAC or up to 16 EVE E-
100Z V3 products on 230 VAC.
1st Product
2nd Product
3rd Product
Additional
Products
Power
Source

Page 6 of 14
SETUP
EVE E-100Z V3 User Manual Rev. 1
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
Orientation
The EVE E-100Z V3 may be mounted in any position; however, make sure adequate ventilation is
provided around the product.
Rigging
• Before deciding on a location, always make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure adequate ventilation is provided around the product.
• Make sure that the structure or surface onto which you are mounting the product can support the
product’s weight. (see the Technical Specifications)
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to
reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the
knobs.
Mounting Diagram
Mounting Bracket
Safety Cable
(such as CH-05 from
Chauvet)
Mounting Clamp
(such as CLP-15 or CLP-15N
from Chauvet)
Bracket
Adjustment Knob

Page 7 of 14
EVE E-100Z V3 User Manual Rev. 1
OPERATION
4. OPERATION
Control Panel Operation
To access the control panel functions, use the four buttons located underneath the display. Please refer to
the Product Overview to see the button locations on the control panel.
Menu Map
Configuration (DMX)
The EVE E-100Z V3 works with a DMX controller. Information about DMX is in the CHAUVET DMX Primer,
which is available from the Chauvet website http://www.chauvetlighting.com/downloads/
DMX_Primer_rev05_WO.pdf.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX
mode uses. If you choose a starting address that is too high, you could restrict the access to some of the
product’s channels.
The EVE E-100Z V3 uses up to 3 DMX channels, which defines the highest configurable address as 510.
If you are not familiar with the DMX protocol, download the DMX Primer from www.chauvetdj.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 1-CH or 3-CH shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address, from d 1–512.
4. Press <ENTER>.
D-Fi USB Connectivity
The PN is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB from Chauvet
DJ. Simply set the product's DMX Personality and DMX Address, set the DIP switch D-Fi receiving/
transmitting channel, then plug it into the D-Fi USB port.
BUTTON FUNCTION
<MENU> Press to find an operation mode or to back out of the current menu option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
MODE PROGRAMMING LEVELS DESCRIPTION
DMX Mode 1-CH d 1–512 Selects DMX personality and starting address
3-CH
Dimmer U-- d000–255 Dimmer level
S000–255 Strobe speed
Dimmer
Speed Mode dIM
OFF
Dimmer speed settings, off, fast, medium, or slow
dIM1
dIM2
dIM3
Fan FAN AUTO Fan speed according to product temperature
ON Fan always on
WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so
may cause damage to the product.
Once plugged in, the D-Fi USB will take over the product. Wired DMX and manual
display control / menu buttons will be unavailable until you unplug the D-Fi USB. The
priority levels are:
1. D-Fi USB
2. Wired DMX 3. Manual Digital Display/Menu Buttons

Page 8 of 14
OPERATION
EVE E-100Z V3 User Manual Rev. 1
Configuration (D-Fi USB)
1. Set the DMX Personality and DMX address on the EVE E-100Z V3.
2. Use the Chart provided to set BOTH:
• the Channel, and then
• The Receiving or Transmitting option
NOTE: DIP Switch 5 is for Transmitting OR Receiving, please choose carefully.
D-Fi USB DIP Switch Channels

Page 9 of 14
EVE E-100Z V3 User Manual Rev. 1
OPERATION
DMX Channel Assignments and Values
3-CH
1-CH
Configuration (Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Dimmer
To set the dimmer level on the EVE E-100Z V3, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER>. Repeat until d000–255 shows on the display.
3. Use <UP> or <DOWN> to increase or decrease the dimmer value.
4. Press <ENTER> to save the value.
5. Press <MENU> to exit the mode.
Strobe
To set the strobe speed on the EVE E-100Z V3, do the following:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER>. Repeat until S000–255 shows on the display.
3. Use <UP> or <DOWN> to increase or decrease the strobe speed.
4. Press <ENTER> to save the value.
5. Press <MENU> to exit the mode.
Dimmer Speed Mode
To set the dimmer speed mode of the EVE E-100Z V3, follow the instructions below:
1. Press <MENU> repeatedly until dIM shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the dimmer speed mode, from OFF, dIM1 (fast), dIM2 (medium),
or dIM3 (slow).
4. Press <ENTER>.
Fan Mode
To set the fan mode of the EVE E-100Z V3, do the following:
1. Press <MENU> repeatedly until FAN shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the fan mode, from AUTO (the fan speed will be set by the
product temperature) or ON (the fan will always be on).
4. Press <ENTER>.
CHANNEL FUNCTION VALUE PERCENT/SETTING
1 Dimmer 000 255 0–100%
2Strobe 000 010 No function
011 255 Strobe (slow to fast)
3 Dimmer Speed Mode
000 051 Dimmer speed set from display
052 101 Dimmer speed mode Off
102 152 Dimmer speed mode 1 - fast
153 203 Dimmer speed mode 2 - medium
204 255 Dimmer speed mode 3 - slow
CHANNEL FUNCTION VALUE PERCENT/SETTING
1 Dimmer 000 255 0–100%
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.

Page 10 of 14
OPERATION
EVE E-100Z V3 User Manual Rev. 1
Master/Slave Mode (Wired)
The Master/Slave mode allows a single EVE E-100Z V3 product (the “master”) to control the actions of one
or more EVE E-100Z V3 products (the “slaves”) without the need of a DMX controller. The master product
will be set to operate in Stand-Alone, while the slave products will be set to operate in Slave mode. Once
set and connected, the slave products will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 1-CH or 3-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Connect the DMX input of the first slave product to the DMX output of the master product.
5. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave
product.
6. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in Stand-Alone mode.
2. Make the master product the first product in the DMX daisy chain.
Master/Slave Mode (D-Fi USB)
The D-Fi USB allows a single EVE E-100Z V3 product (the “master”) to control the actions of one or more
EVE E-100Z V3 products (the “slaves”) without the need of a DMX controller or DMX cables. The master
(transmitter) product will be set to operate in Stand-Alone mode, while the slave (receiver) products will be
set to operate in Slave mode. Once set and connected, the slave products will operate in unison with the
master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 1-CH or 3-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Set the D-Fi USB to receive on a specific channel, 1–16.
5. Plug in the D-Fi USB.
6. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in Stand-Alone mode.
2. Set the D-Fi USB to transmit on the D-Fi channel the slaves are receiving on.
3. Plug in the D-Fi USB.
• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
• Do not connect more than 31 slaves to the master.
• All products must be set to the same DMX personality, DMX address, and D-Fi
channel.
• Configure all the slave products before configuring the master to transmit.
• Never connect a DMX controller to a D-Fi channel configured for Master/Slave
operation because the controller may interfere with the signals from the master.

Page 11 of 14
EVE E-100Z V3 User Manual Rev. 1
MAINTENANCE
5. MAINTENANCE
Product Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean
your lighting products at least twice a month. However, be aware that usage and environmental conditions
could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 12 of 14
TECHNICAL SPECIFICATIONS
EVE E-100Z V3 User Manual Rev. 1
6. TECHNICAL SPECIFICATIONS
Dimensions and Weight
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Light Source
Photometrics
Thermal
DMX
Ordering
LENGTH WIDTH HEIGHT WEIGHT
24 in (611 mm) 7.2 in (183 mm) 16.9 in (430 mm) 12.6 lb (5.7 kg)
POWER SUPPLY TYPE RANGE VOLTAGE SELECTION
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
PARAMETER 120 V, 60 HZ230 V, 50 HZ
Consumption 106 W 103 W
Operating Current 0.9 A 0.5 A
Power linking current (products) 13.6 A (9 products) 13.6 A (16 products)
Fuse T 2A, 250 V T 2A, 250 V
POWER I/O U.S./WORLDWIDE UK/EUROPE
Power input connector Seetronic Powerkon Seetronic Powerkon
Power output connector Seetronic Powerkon Seetronic Powerkon
Power Cord plug Edison (U.S.) Local Plug
TYPE COLOR QUANTITY POWER CURRENT LIFESPAN
LED Warm white 1 100 W 2.3 A 50,000 hours
PARAMETER VALUE
Strobe Rate 0 to 30 Hz
Zoom Angle 14° to 30°
Illuminance @ 2 m (14°) 15,100 lux
Illuminance @ 2 m (30°) 3,800 lux
MAXIMUM EXTERNAL TEMPERATURE COOLING SYSTEM
104 °F (40 °C) Fan-assisted convection
I/O CONNECTOR CHANNEL RANGE
3-pin XLR 1 or 3
PRODUCT NAME ITEM CODE UPC NUMBER
EVE E-100Z V3 03051188 781462215361

Page 13 of 14
EVE E-100Z V3 User Manual Rev. 1
RETURNS
RETURNS
In case you need to get support or return a product:
• If you are located in the U.S., contact Chauvet World Headquarters.
• If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
• If you are located in Mexico, contact Chauvet Mexico.
• If you are located in Benelux, contact Chauvet Europe BVBA.
• If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local
distributor. See www.chauvetdj.com for distributors outside the U.S., UK, Ireland, Mexico, or
Benelux.
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization
(RMA) number before shipping the product. Be prepared to provide the model number, serial number, and
a brief description of the cause for the return.
To submit a service request online, go to www.chauvetdj.com/service-request.
Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet
will not issue call tags.
Clearly label the package with the RMAnumber. Chauvet will refuse any product returned without an RMA
number.
Before sending the product, clearly write the following information on a piece of paper and place it inside
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
distributor of record and follow their instructions on how to return Chauvet products to
them. Visit our website www.chauvetdj.com for contact details.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).

Page 14 of 14
CONTACT US
EVE E-100Z V3 User Manual Rev. 1
CONTACT US
Outside the U.S., United Kingdom, Ireland, Mexico or Benelux, contact the dealer of record. Follow the
instructions to request support or to return a product. Visit our website for contact details.
World Headquarters
General Information Technical Support
Address: 5200 NW 108th Ave. Voice: [phone]
Sunrise, FL 33351 Fax: [phone]
Voice: [phone] Email: [email protected]
Fax: [phone] Website
Toll Free: [phone] www.chauvetlighting.com
EUROPE
General Information Technical Support
Address: Stokstraat 18 Email: [e-mail]
9770 Kruishoutem Website
Belgium www.chauvetlighting.eu
Voice: [phone]
General Information Technical Support
Address: Unit 1C Email: [e-mail]
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website
NG16 6NT www.chauvetlighting.co.uk
Voice: [phone]
Fax: [phone]
MEXICO
General Information Technical Support
Av. de las Partidas 34 - 3B, Zona
Industrial Lerma Email: [e-mail]
Lerma, Edo. de México, CP 52000 Website
Voice: [phone] www.chauvet.com.mx