Chauvet COLORstrip User manual

User Manual

Page 2 of 18 COLORstrip™ User Manual Rev. 6
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What Is Included .............................................................................................................................3
Unpacking Instructions....................................................................................................................3
Claims..................................................................................................................................................... 3
Text Conventions ............................................................................................................................3
Symbols ..........................................................................................................................................3
Disclaimer .......................................................................................................................................3
Product at a Glance ........................................................................................................................4
Safety Notes....................................................................................................................................4
2. Introduction................................................................................................................... 5
Product Overview............................................................................................................................5
Product Dimensions........................................................................................................................6
3. Setup.............................................................................................................................. 7
AC Power........................................................................................................................................7
Fuse Replacement..........................................................................................................................7
Power Linking......................................................................................................................................... 7
Mounting .........................................................................................................................................8
Orientation.............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation....................................................................................................................... 9
Control Panel Operation..................................................................................................................9
Menu Map .......................................................................................................................................9
DMX Linking....................................................................................................................................9
Configuration (DMX)............................................................................................................................... 9
Starting Address..................................................................................................................................... 9
DMX Channel Assignments and Values.......................................................................................10
4-CH..................................................................................................................................................... 10
Configuration (Standalone)...........................................................................................................11
Static Color........................................................................................................................................... 11
Automatic and Sound-Active Mode....................................................................................................... 11
Custom Color........................................................................................................................................ 12
Blackout................................................................................................................................................ 12
Reset.................................................................................................................................................... 12
IRC-6 Infrared Remote Control.....................................................................................................13
IRC-6 Operation.................................................................................................................................... 13
Master/Slave Mode .......................................................................................................................14
Master/Slave Runway Effect.........................................................................................................14
5. Maintenance .................................................................................................................15
Product Maintenance....................................................................................................................15
6. Technical Specifications..............................................................................................16
Returns .............................................................................................................................17
Contact Us........................................................................................................................18

COLORstrip™ User Manual Rev. 6 Page 3 of 18
1.BEFORE YOU BEGIN
What Is
Included
•COLORstrip™
•Power Cord
•Hanging Brackets with Mounting
Hardware (L-Brackets)
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure
to report damage to the carrier immediately may invalidate your claim. In addition, keep the
box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Electrical warning. Not following these instructions may cause
electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. Chauvet
assumes no responsibility or liability for any errors or omissions
that may appear in this manual. Chauvet reserves the right to update the existing
document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Updated
R. Isenstadt 06/22/15 A. Leon 06/29/15

Page 4 of 18 COLORstrip™ User Manual Rev. 6
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•The product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be
sure that they also receive this document.

COLORstrip™ User Manual Rev. 6 Page 5 of 18
2.INTRODUCTION
Product Overview
Power In
Fuse Holder
DMX
In/Out
Master/Slave Out
Safety Loop
Display
Menu Buttons
Power Out
Microphone
Sensitivity Knob
EXT Controller
Port

Page 6 of 18 COLORstrip™ User Manual Rev. 6
Product Dimensions
6 in
155 mm
38 in
965 mm
2.5 in
64 mm

COLORstrip™ User Manual Rev. 6 Page 7 of 18
3.SETUP
AC Power
The COLORstrip™ has an auto-ranging power supply and it can work with an input
voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power
requirements (
circuit breaker, power outlet, and wiring), use the current value listed on the
label affixed to the product’s back panel, or refer to the product
’s specifications chart. The
listed current rating indicates the product’s average current draw under normal conditions.
•Always connect the product to a protected circuit (circuit breaker or fuse).
Make sure the product
has an appropriate electrical ground to avoid the risk
of electrocution or fire.
•
To eliminate unnecessary wear and improve its lifespan, during periods of
non-use completely disconnect the product from power
via breaker or by
unplugging it.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
4. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking The product provides power linking via the Edison outlet located in the back of the product.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 15 COLORstrip™ product
s on 120 VAC or up to
28 COLORstrip™ products on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product
in other markets, you must consult with the
local Chauvet distributor as power linking connectors and requirements may differ
in your country or region.
1st Product
2nd Product
3rd Product
Additional
Products
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 18 COLORstrip™ User Manual Rev. 6
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in the
Safety Notes.
Orientation
The COLORstrip™
may be mounted in any position; however, make sure adequate
ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy access
to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product can support the
product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable. Mount the product
securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp
of appropriate weight
capacity.
•When power linking multiple products, mount the products close enough for power
linking cables to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
Safety Cable
(such as CH-05
from Chauvet)
Mounting Clamp
(such as the CLP-
15N
from Chauvet)
Hanging/Mounting
Bracket
(also used as floor
support)
Bracket Adjustment
Knobs

COLORstrip™ User Manual Rev. 6 Page 9 of 18
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the display.
Please refer to the Product Overview to see the button locations on the control panel.
Button
Function
<MODE>
Press to back out of the current menu option
<ENTER>
Press to activate a menu option or a selected value
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN>
Press to scroll down the list of options or to find a lower value
Menu Map
Mode
Programming Steps
Description
ACt
A000
Blackout
A001
F000–F100
Red (strobe)
A002
F000–F100
Green (strobe)
A003
F000–F100
Blue (strobe)
A004
F000–F100
Yellow (strobe)
A005
F000–F100
Purple (strobe)
A006
F000–F100
Cyan (strobe)
A007
F000–F100
White (strobe)
A008
P000–P100
F000–F100
Color Chase 1 (speed, strobe)
A009
P000–P100
F000–F100
Color Chase 2 (speed, strobe)
A010
P000–P100
F000–F100
Color Chase 3 (speed, strobe)
A011
P000–P100
F000–F100
Color Chase 4 (speed, strobe)
A012
P000–P100
Color Chase 5 (speed)
A013
P000–P100
Color Chase 6 (speed)
A014
P000–P100
Color Chase 7 (speed)
A015
P000–P100
Color Chase 8 (speed)
A016
P000–P100
Color Chase 9 (speed)
A017
P000–P100
Color Chase 10 (speed)
A018
P000–P100
Color Chase 11 (speed)
A019
P000–P100
Color Chase 12 (speed)
A020
P000–P100
Color Chase 13 (speed)
A021 r000–r100
G000–
G100
b000–
b100
F000–
F100
Color Mix
(red, green, blue, strobe)
A022
P000–P100
Color fade (speed)
A023
All Color Chases 1–13 (speed)
SYS
SdAd
001– 509
DMX Address
AAAd
Reset
DMX Linking
The COLORstrip™ works with a DMX controller. Information about DMX is in the
CHAUVET® DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the
selected DMX
mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The COLORstrip™ uses 4 DMX channels, and the highest configurable address is 509.
If you are not familiar with the DMX protocol,
download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MODE>repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until SYS shows on the display.
3. Press <ENTER>.
4. Press <UP> or <DOWN> repeatedly until SdAd show on the display.
5. Press <ENTER>and 001– 508 will show on the display.
6. Use <UP> or <DOWN> to select the starting address.
7. Press <ENTER>.

Page 10 of 18 COLORstrip™ User Manual Rev. 6
DMX Channel Assignments and Values
4-CH
Channel
Function
Value
Percent/Setting
1
Static Colors
000
ó
009
No function
010
ó
119
Red 0–100%
020 ó029 Green 0–100%
030
ó
039
Blue 0–100%
040
ó
049
Yellow 0–100%
050
ó
059
Magenta 0–100%
060
ó
069
Cyan 0–100%
070 ó079 White 0–100%
Color Chases
080
ó
089
Color Chase 1
090
ó
099
Color Chase 2
100
ó
109
Color Chase 3
110
ó
119
Color Chase 4
120 ó129 Color Chase 5
130
ó
139
Color Chase 6
140
ó
149
Color Chase 7
150
ó
159
Color Chase 8
160
ó
169
Color Chase 9
170 ó179 Color Chase 10
180
ó
189
Color Chase 11
190
ó
199
Color Chase 12
200
ó
209
Color Chase 13
RGB Color Mixing
210 ó219 Channels 2–4
Color Fade
220
ó
229
Color Fade
Sound-Active
230 ó255 Sound-Active
2
Run Speed (when
Ch. 1 is 080–209)
000
ó
127
Slow to fast
128
ó
255
Sound-Active
Red (when Ch. 1 is
210–219)
000 ó255 0–100%
Fade Speed (when
Ch. 1 is 220–229)
000 ó255 Slow to fast
3
Strobe (when Ch. 1 is
010–119) 000 ó127 Slow to fast
250
ó
255
Sound-Active
Green (when Ch. 1 is
210–219)
000 ó255 0–100%
4
Blue (when Ch. 1 is
210–119)
000 ó255 0–100%

COLORstrip™ User Manual Rev. 6 Page 11 of 18
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Static Color
To run the COLORstrip™ on a static color, follow the instructions below:
1. Press <MODE>repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until ACt shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to scroll through the menu until A001–A007 shows on the
display.
5. Press <ENTER> and Fxxx will show on the display.
6. Use <UP> or <DOWN> to increase or decrease the strobe value.
•Set F000 for no strobe.
•Set F100 for sound-active strobe (Sensitivity knob must be turned up).
•Set F001–F099 for auto strobe, from slow to fast.
7. Press <ENTER>.
Automatic and
Sound-
Active
Mode
To run a color chase, do the following:
1. Press <MODE>repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until ACt shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to scroll through the menu until A008–A020 or A022–A023
shows on the display.
5. Press <ENTER> and Pxxx will show on the display.
6. Use <UP> or <DOWN> to increase or decrease the program speed.
7. Set P000 for sound-active only (Sensitivity knob must be turned up).
8. Set P001–P100 for auto mode, from slow to fast.
9. Press <ENTER>. For A008–A011, Fxxx will show on the display.
10. Use <UP> or <DOWN> to increase or decrease the strobe value.
11. Set F000 for no strobe.
12. Set F100 for sound-active strobe (Sensitivity knob must be turned up).
13. Set F001–F099 for auto strobe, from slow to fast.
14. Press <ENTER>.
For Sound-Active mode, turn the Sensitivity knob up until the product responds to the
beat of the music.
In Sound-Active modes, the product will only respond to low frequencies of music
(bass and drums).

Page 12 of 18 COLORstrip™ User Manual Rev. 6
Custom Color
To custom mix a color, follow the instructions below:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until ACt shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to scroll through the menu until A021 shows on the display.
5. Press <ENTER> and rxxx will show on the display.
6. Use <UP> or <DOWN> to increase or decrease the red value.
7. Press <ENTER> and Gxxx will show on the display.
8. Use <UP> or <DOWN> to increase or decrease the green value.
9. Press <ENTER> and bxxx will show on the display.
10. Use <UP> or <DOWN> to increase or decrease the blue value.
11. Press <ENTER> and Fxxx will show on the display.
12. Use <UP> or <DOWN> to increase or decrease the strobe value.
•Set F000 for no strobe.
•Set F100 for sound-active strobe (Sensitivity knob must be turned up).
•Set F001–F099 for auto strobe, from slow to fast.
13. Press <ENTER>. Repeat steps 3 – 12 as necessary.
Blackout
To black out the COLORstrip™, do the following:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until ACt shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to scroll through the menu until A000 shows on the display.
5. Press <ENTER>.
Reset
To reset the COLORstrip™, follow the instructions below:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until SYS shows on the display.
3. Press <ENTER>.
4. Press <UP> or <DOWN> repeatedly until AAAd shows on the display.
5. Press
<ENTER>
.

COLORstrip™ User Manual Rev. 6 Page 13 of 18
IRC-6 Infrared
Remote
Control
The COLORstrip™ is compatible with the IRC-6 infrared remote control from Chauvet.
Make sure to point the IRC-6 directly at the receiver on the front of the product.
IRC-6 Operation
Static Color Mode
Static Color mode will enable the product to output a preset color.
To run Static Color mode:
Press <0> – <9> to choose between the different preset static colors.
Automatic/Sound-Active Mode
Automatic/Sound-Active mode will enable you to run the automatic programs on the
product. The product will also respond to music if the sensitivity knob is set high enough.
To turn on Automatic/Sound-Active mode:
1. Press <AUTO> or <SOUND> on the IRC.
2. Press <0> – <9>, or <FADE> to choose between the different programs.
To change the auto program speed:
Press <+> or <–> to increase or decrease the auto program speed.
To turn off Automatic/Sound-Active mode and return to Static Color mode:
Press <AUTO> or <SOUND> on the IRC.
COLORstrip™ IRC-6 Buttons:
Static Color Mode
Auto/Sound Mode
<0> - A007 (White)
<0> - A008
<1> - A001 (Red)
<1> - A009
<2> - A021(Amber)
<2> - A010
<3> - A004 (Yellow)
<3> - A011
<4> - A002 (Green)
<4> - A012
<5> - A006 (Cyan)
<5> - A013
<6> - A003 (Blue)
<6> - A014
<7> - A005 (Purple)
<7> - A015
<8> - A021(Pink)
<8> - A017
<9> - A021(Sunflower)
<9> - A023
<FADE> - No function
<FADE> - A022 (no response to sound)
Manual Color Control
To manually control the RGB percentage:
1. Press <MANUAL> on the IRC.
2. Press <R> (red), <G> (green), or <B> (blue) to choose the color.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To black out the lights:
Press <BLACK OUT> on the IRC.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC will not respond to any inputs when Black Out is activated. If the remote
does not respond when a button is pressed, try pressing <BLACK OUT>. You
may have inadvertently activated Black Out.

Page 14 of 18 COLORstrip™ User Manual Rev. 6
Master/Slave
Mode
The Master/Slave mode allows a single COLORstrip™ product (the “master”) to control the
actions of one or more COLORstrip™ product
s (the “slaves”) without the need of a DMX
controller. The master product will be set to operate in either Automatic or Sound-Active
mode, while the slave product
s will be set to operate in Slave mode. Once set and
connected, the slave products will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until SYS shows on the display.
3. Press <ENTER>.
4. Press <UP> or <DOWN> repeatedly until SdAd shows on the display.
5. Press <ENTER>, and 001– 508 will show on the display.
6. Set the DMX address to 001.
7. Connect the DMX input of the first slave product to the DMX output of the master
product. SLA will show on the display.
8. Connect the DMX input of the subsequent slave products to the DMX output of the
previous slave product.
9. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to run in auto or sound mode.
2. Make the master product the first product in the DMX daisy chain.
•Configure all the slave product
s before connecting the master to the daisy
chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
•
Do not connect more than 31 slaves to the master.
Master/Slave
Runway Effect
The Master/Slave Runway Effect mode allows a single COLORstrip™ product (the master)
to control the actions of one or more COLORstrip™ products (the slaves)
in a runway
effect without the need of a DMX controller. The master product will be set to operate on
specific programs in either Automatic or Sound-
Active mode, while the slave products will
be set to operate in Slave mode. Once set and connected, the
program will run smoothly
from product to product.
Configure the products as indicated below.
Slave products:
1. Press <MODE> repeatedly until SYS or ACt shows on the display.
2. Press <UP> or <DOWN> repeatedly until SYS shows on the display.
3. Press <ENTER>.
4. Press <UP> or <DOWN> repeatedly until SdAd shows on the display.
5. Press <ENTER>, and 001– 508 will show on the display.
6. Set the DMX address to 001.
7. Connect the DMX input of the subsequent slave products to the Master/Slave output
of the previous slave product.
8. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to run in auto or sound mode, A014–A020.
2. Connect the DMX input of the first slave product to the Master/Slave output of the
master product. SLA will show on the displays of the slaves.
•Configure all the slave products before connecting the master to the daisy
chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
•
Do not connect more than 31 slaves to the master.

COLORstrip™ User Manual Rev. 6 Page 15 of 18
5.MAINTENANCE
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can lead
to reduction of the light source’s life and/or
mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting products at least
twice a month.
However, be aware that usage and environmental conditions could be contributing factors
to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 16 of 18 COLORstrip™ User Manual Rev. 6
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
38 in (965 mm)
2.5 in (64 mm)
6 in (155 mm)
4.5 lb (2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
72 W
73 W
Operating Current
0.6 A
0.3 A
Power linking current
(products)
8 A (15 products) 8 A (28 products)
Fuse
F 1 A, 250 V
F 1 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
0.25 W
100,000 hours
Color
Quantity
Current
Red
128
20 mA
Green
128
20 mA
Blue
128
20 mA
Photometrics
Parameter
Beam Angle
53° x 27°
Field Angle
68° x 46°
Illuminance @ 2 m
1,104 lux
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
3-pin XLR
4
Ordering
Product Name
Item Code
UPC Number
COLORstrip™
10051063
781462214111

COLORstrip™ User Manual Rev. 6 Page 17 of 18
R
ETURNS
In case you need to get support or return a product:
•If you are located in the U.S., contact Chauvet World Headquarters.
•If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
•If you are located in Mexico, contact Chauvet Mexico.
•If you are located in Benelux, contact Chauvet Europe BVBA.
•If you are located in any other country, DO NOT contact Chauvet. Instead, contact
your local distributor. See www.chauvetlighting.com for distributors outside the U.S.,
UK, Ireland, Mexico, or Benelux.
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
distributor of record and follow their instructions on how to return Chauvet
products to them. Visit our website www.chauvetlighting.com for contact details.
Call the corresponding Chauvet Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
Send the merchandise prepaid, in its original box, and with its original packing and
accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are
recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).

Page 18 of 18 COLORstrip™ User Manual Rev. 6
C
ONTACT
U
S
WORLD HEADQUARTERS - Chauvet
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.co.uk
MEXICO - Chauvet Mexico
General Information
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: s[email protected]om.mx
World Wide Web www.chauvet.com.mx
CHAUVET EUROPE - Chauvet Europe BVBA
General Information
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.eu
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux
contact your dealer. Follow their
instructions to request support or to return a product. Visit our website for contact details.