Chauvet SlimPar Q12 USB User manual

SlimPA R Q12
User Manual

TABLE OF CONTENTS
SlimPAR Q12 USB User Manual Rev. 3
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 1
What Is Included ........................................................................................... 1
Unpacking Instructions.................................................................................. 1
Claims ............................................................................................................... 1
Text Conventions.......................................................................................... 1
Symbols ........................................................................................................ 1
Disclaimer ..................................................................................................... 1
Product at a Glance ...................................................................................... 2
Safety Notes.................................................................................................. 2
2. Introduction ................................................................................ 3
Product Overview.......................................................................................... 3
Product Dimensions...................................................................................... 4
3. Setup ........................................................................................... 5
AC Power...................................................................................................... 5
Fuse Replacement............................................................................................ 5
Power Linking.................................................................................................... 5
Mounting ....................................................................................................... 6
Orientation......................................................................................................... 6
Rigging.............................................................................................................. 6
4. Operation .................................................................................... 7
Control Panel Operation................................................................................ 7
Menu Map..................................................................................................... 7
DMX Linking.................................................................................................. 8
Configuration (DMX).......................................................................................... 8
D-Fi USB Connectivity....................................................................................... 8
D-Fi USB Connectivity .................................................................................. 8
Configuration (D-Fi USB) .................................................................................. 8
DMX Personality and Starting Address......................................................... 9
DMX Channel Assignments and Values....................................................... 9
9-CH.............................................................................................................. 9
4-CH.............................................................................................................. 10
Configuration (Standalone) ............................................................................... 10
Automatic Programs.......................................................................................... 10
Auto-Program Speed......................................................................................... 10
Sound-Active Mode........................................................................................... 11
Sound Sensitivity............................................................................................... 11
Preset Color Mode ............................................................................................ 11
Custom Color Mixing......................................................................................... 11
Dimmer Speed Mode ........................................................................................ 11
IRC-6 Infrared Remote Control..................................................................... 12
IRC-6 Operation................................................................................................ 12
Master/Slave Mode (Wired) .......................................................................... 13
Master/Slave Mode (D-Fi USB)..................................................................... 13
5. Maintenance................................................................................ 14
Product Maintenance.................................................................................... 14
6. Technical Specifications ........................................................... 15
7. Returns ........................................................................................ 16
7. Contact Us .................................................................................. 17

Page 1 of 17
SlimPAR Q12 USB User Manual Rev. 3
BEFORE YOU BEGIN
1. BEFORE YOU BEGIN
What Is Included
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Symbols
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetdj.com.
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2017 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, D-Fi USB, and SlimPAR Q12 USB are registered trademarks or trademarks
of Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Other company and product names and logos referred to herein may be trademarks of their respective
companies.
• SlimPAR Q12 USB
• Power Cord • Warranty Card • Quick Reference Guide
CONVENTION MEANING
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
Menu Settings A sequence of menu options to be followed
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
SYMBOL MEANING
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.

Page 2 of 17
BEFORE YOU BEGIN
SlimPAR Q12 USB User Manual Rev. 3
Product at a Glance
Safety Notes
Use on Dimmer Auto Programs 
Outdoor Use Auto-ranging Power Supply 
Sound-Active Replaceable Fuse 
DMX User-Serviceable 
Master/Slave 
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing the
fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• Ifmounting the product overhead, always secure to a fastening device using a safety cable.
• Make sure there are no flammable materials close to the product when operating.
• Do not touch the product’s housing when operating because it may be very hot.
• The product is not intended for permanent installation.
• Always make sure that the voltage of the outlet to which you are connecting the product is
within the range stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the
product to rain or moisture.
• Alwaysinstall the product in a locationwithadequate ventilation, at least 20 in(50cm) from
adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the hanging/
mounting bracket.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at
higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to damage
or malfunction. Please contact the nearest authorized technical assistance center.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be sure that
they also receive this document.

Page 3 of 17
SlimPAR Q12 USB User Manual Rev. 3
INTRODUCTION
2. INTRODUCTION
Product Overview
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Safety Loop
Microphone
DMX In/Out
Fuse Holder
Power In
Menu Buttons
Power Out
Display
D-Fi USB Port
Lenses IR Sensor
Back Panel View
Front View

Page 4 of 17
INTRODUCTION
SlimPAR Q12 USB User Manual Rev. 3
Product Dimensions
9.7 in
247 mm 3.6 in
92 mm
11.5 in
293 mm

Page 5 of 17
SlimPAR Q12 USB User Manual Rev. 3
SETUP
3. SETUP
AC Power
The SlimPAR Q12 USB has an auto-ranging power supply and it can work with an input voltage range of
100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet,
and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the
product’s specifications chart. The listed current rating indicates the product’s average current draw under
normal conditions.
Fuse Replacement
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating.
4. Insert the fuse holder back in place and reconnect power.
Power Linking
The product provides power linking via the Edison outlet located in the back of the product. Please see the
diagram below for further explanation.
Power Linking Diagram
• Always connect the product to a protected circuit (a circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-
use completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
Disconnect the product from the power outlet before replacing the fuse.
You can power link up to 12 SlimPAR Q12 USB products on 120 VAC or up to 21
SlimPAR Q12 USB products on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product in other markets, you must consult with the local
Chauvet distributor as power linking connectors and requirements may differ in
your country or region.
Safety cap
Spare fuse holder
(inside safety cap)
Installed fuse
(held by plastic clip)
1st Product
2nd Product
Additional
Products
3rd Product

Page 6 of 17
SETUP
SlimPAR Q12 USB User Manual Rev. 3
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
Orientation
The SlimPAR Q12 USB may be mounted in any position; however, make sure adequate ventilation is
provided around the product.
Rigging
• Before deciding on a location, always make sure there is easy access to the product for
maintenance and programming purposes.
• Make sure that the structure or surface onto which you are mounting the product can support the
product’s weight. (see the Technical Specifications)
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power linking cables to
reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the
knobs.
Mounting Diagram
Mounting Bracket
Safety Cable
(such as CH-05 from
Chauvet)
Mounting Clamp
(such as CLP-15N from
Chauvet)
BracketAdjustment
Knob

Page 7 of 17
SlimPAR Q12 USB User Manual Rev. 3
OPERATION
4. OPERATION
Control Panel Operation
To access the control panel functions, use the four buttons located underneath the display. Please refer to
the Product Overview to see the button locations on the control panel.
Menu Map
BUTTON FUNCTION
<MENU> Press to find an operation mode or to back out of the current menu option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
MODE PROGRAMMING LEVELS DESCRIPTION
4-CH d 1-512 4-channel DMX mode
9-CH 9-channel DMX mode
C
(preset colors)
C1 Static red
C2 Static green
C3 Static blue
C4 Static amber
C5 Static cyan
C6 Static magenta
C7 Static yellow
C8 Static orange
C9 Static lime
C10 Static lavender
C11 Static sky
C12 Static hot pink
C13 Static sea foam green
C14 Static salmon
C15 Static pink
C16 Static powder blue
C17 Static bright yellow
C18 Static peach
C19 Static white
P--
(auto program)
P1 4-color program (snap)
P2 4-color program (pulse)
P3 19-color program (snap)
P4 19-color program (fading)
S-- S--1-100 Program speed for P1-P4
Snd
(sound-active) Snd 1 4-color program (sound-active)
Snd 2 19-color program (sound active)
SenS u-0-100 Sound Sensitivity Setting
U--
(custom colors)
r000-255 Custom static colors
Combines red, green, and blue
g000-255
b000-255
A000-255
dIM
OFF
Dimmer speed mode, fast to slow, or off
dIM1
dIM2
dIM3
SEr ON IR function on or off
OFF

Page 8 of 17
OPERATION
SlimPAR Q12 USB User Manual Rev. 3
DMX Linking
The SlimPAR Q12 USB works with a DMX controller. Information about DMX is in the CHAUVET® DMX
Primer, which is available from the Chauvet website http://www.chauvetlighting.com/downloads/
DMX_Primer_rev05_WO.pdf.
Configuration (DMX)
Set the product in DMX mode to control with a DMX controller
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the
product.
D-Fi USB Connectivity
The SlimPAR Q12 USB is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi
USB from Chauvet DJ. Simply set the product's DMX Personality and DMX Address, set the DIP switch D-
Fi receiving/transmitting channel, then plug it into the D-Fi USB port.Press <MENU> repeatedly until 5Ch,
6Ch, 8Ch, 10Ch, 17Ch, 32Ch, or 36Ch shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select the starting address, from d 1–512.
5. Press <ENTER>.
D-Fi USB Connectivity
The PN is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi USB from Chauvet
DJ. Simply set the product's DMX Personality and DMX Address, set the DIP switch D-Fi receiving/
transmitting channel, then plug it into the D-Fi USB port.
Configuration (D-Fi USB)
1. Set the DMX Personality and DMX address on the SlimPAR Q12 USB .
2. Use the Chart provided to set BOTH:
• the Channel, and then
• The Receiving or Transmitting option
NOTE: DIP Switch 5 is for Transmitting OR Receiving, please choose carefully.
WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so
may cause damage to the product.
Once plugged in, the D-Fi USB will take over the product. Wired DMX and manual
display control / menu buttons will be unavailable until you unplug the D-Fi USB. The
priority levels are:
1. D-Fi USB
2. Wired DMX 3. IRC-6 Remote Control 4. Manual Digital Display/Menu Buttons

Page 9 of 17
SlimPAR Q12 USB User Manual Rev. 3
OPERATION
D-Fi USB DIP Switch Channels
DMX Personality and Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses.
If you choose a starting address that is too high, you could restrict the access to some of the product’s channels.
The SlimPAR Q12 USB uses up to 9 DMX channels in an 9-CH DMX mode, which defines the highest configurable
address to 504.
If you are not familiar with the DMX protocol, download the DMX Primer from www.chauvetlighting.com
To select the starting address, do the following:
1. Press <MENU> repeatedly until 4-CH or 9-CH shows on display.
2. Press <ENTER> and d--1-d512 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
DMX Channel Assignments and Values
9-CH
CHANNEL FUNCTION VALUE PERCENT/SETTING
1 Red 000 255 0–100%
2 Green 000 255 0–100%

Page 10 of 17
OPERATION
SlimPAR Q12 USB User Manual Rev. 3
4-CH
Configuration (Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Connect the product to a suitable power outlet.
Automatic Programs
To run the SlimPAR Q12 USB in automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select an automatic program, from P (1–14).
4. Press <ENTER>.
Auto-Program Speed
To change the auto-program speed on the SlimPAR Q12 USB , do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to increase or decrease the program speed, from (S 1–100).
3. Press <ENTER>. The product will return to the last selected mode.
3 Blue 000 255 0–100%
4 Amber 000 255 0–100%
5Color Macros
(Overrides Ch. 1-4) 000 015 No function
016 255 Color macros
6
Strobe
(when CH7 is 000-031) 000 015 No function
016 255 Slow to fast
Speed
(when CH7 is 032-223) 000 255 Slow to fast
Sound sensitivity
(when CH7 is 224-255) 000 010 Off
011 255 Controls the sound sensitivity level
7 Mode
000 031 No function
032 063 Pulse effect 0-100% CH1~4 must be
active
064 095 Pulse effect 100%-0
096 127 Pulse effect 100%-0-100%
128 159 Auto fade transition
160 191 Auto snap transition (4 colors)
192 223 Auto snap transition (19 colors)
224 255 Sound active mode
8 Dimmer 000 255 0–100%
9 Dimmer Speed
000 051 Default dimmer speed set from menu
052 101 Dimmer speed mode off
102 152 Dimmer speed mode 1 (fast speed)
153 203 Dimmer speed mode 2 (medium speed)
204 255 Dimmer speed mode 3 (slow speed)
CHANNEL FUNCTION VALUE PERCENT/SETTING
1 Red 000 255 0–100%
2 Green 000 255 0–100%
3 Blue 000 255 0–100%
4 Amber 000 255 0–100%
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
CHANNEL FUNCTION VALUE PERCENT/SETTING

Page 11 of 17
SlimPAR Q12 USB User Manual Rev. 3
OPERATION
Sound-Active Mode
To run the SlimPAR Q12 USB in sound-active mode, follow the instructions below:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER>
3. Use <UP> and <DOWN> to select a sound active program (Snd1 or Snd2)
4. Press <ENTER>.
Sound Sensitivity
To set the sound sensitivity on the SlimPAR Q12 USB , do the following:
1. Press <MENU> repeatedly until SenS shows on the display.
2. Use <UP> or <DOWN> to increase or decrease the sound sensitivity, from (u 0–100).
3. Press <ENTER>.
Preset Color Mode
To run the SlimPAR Q12 USB on a static color, follow the instructions below:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select a static color, from (C 1–18).
4. Press <ENTER>.
Custom Color Mixing
To custom mix a static color, do the following:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following will show on display.
•r_ _ _ (red)
•g_ _ _ (green)
•b_ _ _ (blue)
•A_ _ _ (amber)
3. Press <ENTER> to cycle through the color settings.
4. When the desired color shows on the display, use <UP> or <DOWN> to increase or decrease the
color value.
5. Repeat steps 3 and 4 until the product outputs as desired.
Dimmer Speed Mode
To set the dimmer speed mode of the SlimPAR Q12 USB , follow the instructions below:
1. Press <MENU> repeatedly until dIM shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select:
•dIM1 (fast)
•dIM2 (medium)
•dIM3 (slow)
• or OFF
4. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).

Page 12 of 17
OPERATION
SlimPAR Q12 USB User Manual Rev. 3
IRC-6 Infrared Remote Control
The SlimPAR Q12 USB is compatible with the IRC-6 infrared remote control from Chauvet. To activate IR
mode, follow the instructions below:
1. Press <MENU> repeatedly until SEr shows on the display.
2. Press <ENTER> to accept.
3. Press <UP> or <DOWN> to select ON or OFF.
4. Press <ENTER>.
IRC-6 Operation Automatic Mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC-6.
2. Press <+> or <–> to increase or decrease the speed of the program.
Sound-Active Mode
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
1. Press <SOUND> on the IRC-6
2. Press <+> or <–> to select Snd1 or Snd2.
To adjust the sound sensitivity in Sound Active mode:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <+> or <–> to increase or decrease the sound sensitivity.
Manual Color Control
To choose a specific color with the IRC-6:
1. Press <MANUAL> on the IRC-6
2. Press any number between <0>~<9> to choose a preset color
To manually control the RGB percentage:
1. Press <MANUAL> on the IRC-6.
2. Press <R> (red), <G> (green), <B> (blue), or <A> (amber) to choose your
color.
3. Press <+> or <–> to increase or decrease the value of each color.
Miscellaneous Operation
To adjust the total output level:
1. Press <%> on the IRC-6.
2. Press <+> or <–> to increase or decrease the output level.
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To select only fading programs:
1. Press <FADE> on the IRC-6.
2. Press <+> or <–> to select P2 or P4.
To black out the lights:
1. Press <BLACK OUT> on the IRC-6.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC-6 will not respond to any inputs when Black Out is activated. If the
remote does not respond when a button is pressed, try pressing <BLACK OUT>.
You may have inadvertently activated Black Out.

Page 13 of 17
SlimPAR Q12 USB User Manual Rev. 3
OPERATION
Master/Slave Mode (Wired)
The Master/Slave mode allows a single SlimPAR Q12 USB product (the “master”) to control the actions of
one or more SlimPAR Q12 USB products (the “slaves”) without the need of a DMX controller. The master
product will be set to operate in Stand-Alone, while the slave products will be set to operate in Slave mode.
Once set and connected, the slave products will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 4-CH or 9-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Connect the DMX input of the first slave product to the DMX output of the master product.
5. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave
product.
6. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in Stand-Alone mode.
2. Make the master product the first product in the DMX daisy chain.
Master/Slave Mode (D-Fi USB)
The D-Fi USB allows a single SlimPAR Q12 USB product (the “master”) to control the actions of one or
more SlimPAR Q12 USB products (the “slaves”) without the need of a DMX controller or DMX cables. The
master (transmitter) product will be set to operate in Stand-Alone mode, while the slave (receiver) products
will be set to operate in Slave mode. Once set and connected, the slave products will operate in unison
with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 4-CH or 9-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Set the D-Fi USB to receive on a specific channel, 1–16.
5. Plug in the D-Fi USB.
6. Finish setting and connecting all the slave products.
Master product:
1. Press <MENU> repeatedly until the DMX personality the slaves are set to shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d -1.
4. Set the master product to operate in either Stand-Alone mode or with the IRC-6.
5. Set the D-Fi USB to transmit on the D-Fi channel the slaves are receiving on.
6. Plug in the D-Fi USB.
• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
• Do not connect more than 31 slaves to the master.
• All products must be set to the same DMX personality, DMX address, and D-Fi
channel.
• Configure all the slave products before configuring the master to transmit.
• Never connect a DMX controller to a D-Fi channel configured for Master/Slave
operation because the controller may interfere with the signals from the master.

Page 14 of 17
MAINTENANCE
SlimPAR Q12USB User Manual Rev. 3
5. MAINTENANCE
Product Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean
your lighting products at least twice a month. However, be aware that usage and environmental conditions
could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Page 15 of 17
SlimPAR Q12 USB User Manual Rev. 3
TECHNICAL
6. TECHNICAL SPECIFICATIONS
Dimensions and Weight
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Light Source
Photometrics
Thermal
DMX
Ordering
LENGTH WIDTH HEIGHT WEIGHT
31 in (785 mm) 2.6 in (67 mm) 4.8 in (123 mm) 9.6 lb (4.4 kg)
POWER SUPPLY TYPE RANGE VOLTAGE SELECTION
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
PARAMETER 120 V, 60 HZ230 V, 50 HZ
Consumption 108 W 105 W
Operating Current 1.5 A 1 A
Power linking current (products) 8 A (5 products) 8 A (9 products)
Fuse T 2A, 250 V T 2A, 250 V
POWER I/O U.S./WORLDWIDE UK/EUROPE
Power input connector IEC IEC
Power output connector Edison IEC
Power Cord plug Edison (U.S.) Local Plug
TYPE COLOR QUANTITY POWER CURRENT LIFESPAN
LED Tri-color RGB 10 9 W 2 A 50,000 hours
STROBE RATE BEAM ANGLE FIELD ANGLE
0 to 25 Hz 20° 34°
MAXIMUM EXTERNAL TEMPERATURE COOLING SYSTEM
104 °F (40 °C) Convection
I/O CONNECTOR CHANNEL RANGE
3-pin XLR 5, 6, 8, 10, 17, 32 or 36
PRODUCT NAME ITEM CODE UPC NUMBER
SlimPAR Q12 USB 03031241 781462215897

Page 16 of 17
RETURNS
SlimPAR Q12 USB User Manual Rev. 3
RETURNS
In case you need to get support or return a product:
• If you are located in the U.S., contact Chauvet World Headquarters.
• If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
• If you are located in Mexico, contact Chauvet Mexico.
• If you are located in Benelux, contact Chauvet Europe BVBA.
• If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local
distributor. See www.chauvetdj.com for distributors outside the U.S., UK, Ireland, Mexico, or
Benelux.
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization
(RMA) number before shipping the product. Be prepared to provide the model number, serial number, and
a brief description of the cause for the return.
To submit a service request online, go to www.chauvetdj.com/service-request.
Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet
will not issue call tags.
Clearly label the package with the RMAnumber. Chauvet will refuse any product returned without an RMA
number.
Before sending the product, clearly write the following information on a piece of paper and place it inside
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
distributor of record and follow their instructions on how to return Chauvet products to
them. Visit our website www.chauvetdj.com for contact details.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).

Page 17 of 17
SlimPAR Q12 USB User Manual Rev. 3
CONTACT US
CONTACT US
Visit the applicable website above to verify our contact information and instructions to request support.
Outside the U.S., United Kingdom, Ireland, Mexico or Benelux, contact the dealer of record.
World Headquarters
General Information Technical Support
Address: 5200 NW 108th Ave. Voice: [phone]
Sunrise, FL 33351 Fax: [phone]
Voice: [phone] Email: [email protected]
Fax: [phone] Website
Toll Free: [phone] www.chauvetlighting.com
EUROPE
General Information Technical Support
Address: Stokstraat 18 Email: [email protected]
9770 Kruishoutem Website
Belgium www.chauvetlighting.eu
Voice: [phone]
General Information Technical Support
Address: Unit 1C Email: [email protected]
Brookhill Road Industrial Estate Website
Pinxton, Nottingham, UK www.chauvetlighting.co.uk
NG16 6NT
Voice: [phone]
Fax: [phone]
MEXICO
General Information Technical Support
Address: Av. de las Partidas 34 - 3B Email: [email protected]
Zona Industrial Lerma Website
Lerma, Edo. de México, CP 52000 www.chauvet.com.mx
Voice: [phone]