Cheminees Philippe RADIANTE 700 User manual

RAD ANTE 700 STANDARD NSTALLAT ON
LEGEND
Firebox Dimension
Exact Dimension
Minimum Dimension
Air ntake
Air Outlet
F REPLACE
CONSTRUCT ON STEP 1
F REPLACE
CONSTRUCT ON STEP 2
SECT ON ‘A’
A
500
1110
498
630
Flue
Lintel
Firebox
Air Grille
Firerock nsulation
Hearth Fireplace base
500
1800
See note [3]
50
860 850
To ceiling height
Cutaway
showing
lintel
850
Mesh
vent
Air grilles to be
either large front
as shown, or sides
x2 (dotted).
Mesh vents
630
50
600
IMPORTANT:
NO BRICKWORK TO
BE COMMENCED
UNTIL FIREBOX IS
PLACED IN POSITION
NOTES:
[1] Air intake grilles minimum air flow area required
= 180cm2each side.
[2] Air outlet grilles minimum air flow area = 240cm2each side
and 480cm2if one grille is used.
[3] Hearth height dimensions optional (Refer to Technical Data
& nstallation nstructions)
[4] All dimensions in millimetres.
[5] Heater can be left freestanding.
[6] Do not scale from these diagrams
[7] Air transfer kits mandatory for exempt units to comply to
AS/NZ 4012/4013:2014. Fan optional depending
on duct length. ( Refer to Technical Data & nstallation
nstructions )
August 2018
Cheminees Philippe’s policy is one of continuous development. We reserve the right to change sizes and specifications without notice.
430 Johnston St., Abbotsford, Victoria 3067 Phone: [phone]
e-mail: [email protected] www.chemphilaust.com.au
Air Transfer Kit
Ceiling
Brick Masonry
OR
50mm Skamotec 225
*
*
*
*
= 30mm air gap
to combustibles
w en using
Skamotec

OPT ONAL NSTALLAT ON 1
RAD ANTE 700
LEGEND
Firebox Dimension
Exact Dimension
Minimum Dimension
Air ntake
Air Outlet
Brick Masonry
F REPLACE
CONSTRUCT ON STEP 1
F REPLACE
CONSTRUCT ON STEP 2
To ceiling height
Cutaway
showing
lintel
A
500
1110
498
630
Flue
Lintel
Firebox
Air Grille
Firerock nsulation
Hearth Fireplace base
500
1800
See note [3]
50
860
850
630
50
600
SECT ON ‘A’
Mesh
vent
Air grilles to be
either large front
as shown, or sides
x2 (dotted).
Mesh vents
850
200
IMPORTANT:
NO BRICKWORK TO
BE COMMENCED
UNTIL FIREBOX IS
PLACED IN POSITION
NOTES:
[1] Air intake grilles minimum air flow area required
= 180cm2each side.
[2] Air outlet grilles minimum air flow area = 240cm2each side
and 480cm2if one grille is used.
[3] Hearth height dimensions optional (Refer to Technical Data
& nstallation nstructions)
[4] All dimensions in millimetres.
[5] Heater can be left freestanding.
[6] Do not scale from these diagrams
[7] Air transfer kits mandatory for exempt units to comply to
AS/NZ 4012/4013:2014. Fan optional depending
on duct length. ( Refer to Technical Data & nstallation
nstructions )
August 2018
Cheminees Philippe’s policy is one of continuous development. We reserve the right to change sizes and specifications without notice.
430 Johnston St., Abbotsford, Victoria 3067 Phone: [phone]
e-mail: [email protected] www.chemphilaust.com.au
Air Transfer Kit
Ceiling
Brick Masonry
OR
50mm Skamotec 225
*
*
*
*
= 30mm air gap
to combustibles
w en using
Skamotec