CHENGDU VANTRON TECHNOLOGY AP6255 User manual

User manual
Product Name: Module
Model Name: AP6255
Manufacture: Chengdu Vantron Technology, Ltd.

Features:
•IEEE 802.11a/b/g/n/ac dual-band radio with virtual-simultaneous dual-band
operation
•Single-stream spatial multiplexing up to 433.3 Mbps data rate.
•Supports 20, 40, 80 MHz channels with optional SGI(256 QAM modulation)
•Supports Bluetooth V4.2+EDR with integrated PA for Class 1.5 and Low Energy
(BLE).
•Concurrent Bluetooth, and WLAN operation
•Simultaneous BT/WLAN receive with single antenna
•Supports standard SDIO v3.0 and backward compatible with SDIO v2.0 host
interfaces.
- SDIO v3.0(4-bit) —up to 208 MHz clock rate in SDR104 mode
•BT host digital interface:
- UART (up to 4 Mbps)
•IEEE Co-existence technologies are integrated die solution
•ECI —enhanced coexistence support, ability to coordinate BT SCO transmissions
around WLAN receives
•

Front view
Back view

General Specification:
Voltages：

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject
to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement
Le modular peut être installéou intégrédans un mobile ou réparer une seule chose
Installation dans n’importe quel appareil portable.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration de rayonnement IC
Ce modular complies avec des radiations émettrices de rayonnement Environnement.
Ceci ne doit pas être co-localiséou opérer avec des autres Ce modular doit être
installéet obtenu avec une distance minimale de 20 cm entre les radiateurs et le
corps de l’utilisateur.

Antenna requirements
1. Antenna List:
Antenna type: PIFA Antenna
Connector Type: USS RFI
BT Antenna Gain:2.8dBi
Antenna impedance: 50 (Ω)
Frequency range: 2400-2500MHz/5150-5850MHz
This device is intended only for OEM integrators under the following conditions:
(For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20 cm between the radiator & your body.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée
entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplantéavec un autre émetteur ou
antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais
supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur
OEM est toujours responsable des essais sur son produit final pour toutes exigences
de conformitésupplémentaires requis pour ce module installé.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED
établies pour un environnement non contrôlé. Cet équipement doit être installéet
utiliséavec un minimum de 20 cm de distance entre la source de rayonnement et
votre corps.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
2.4GWIFI Antenna Gain:2.8dBi
5G WIFI Antenna Gain:2.9dBi