Texas Instruments TUSB564RNQ User manual

1
SLLU288–March 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
User's Guide
SLLU288–March 2018
TUSB564RNQ Evaluation Module
This user's guide describes the characteristics and use of the TUSB564RNQ evaluation module. This
document describes how to power up the EVM and also includes schematics that can be used as
reference design for the Alternate mode implementations of the system with the TUSB564 device.
Contents
1 Introduction ................................................................................................................... 2
2 TUSB564RNQ EVM......................................................................................................... 2
3 TUSB564RNQ EVM Configuration........................................................................................ 3
3.1 TUSB564RNQ EVM Default Configuration...................................................................... 3
3.2 TUSB564 Equalization Control.................................................................................... 3
3.3 Power................................................................................................................. 4
4 TUSB564RNQ EVM Schematics and Bill of Materials.................................................................. 5
4.1 Schematics .......................................................................................................... 5
4.2 Bill of Materials...................................................................................................... 9
List of Figures
1 TUSB564RNQ EVM......................................................................................................... 2
2 Test Board Setup............................................................................................................ 2
3 TUSB564RNQ EVM Main Schematic..................................................................................... 5
4 TUSB564RNQ EVM Configuration Pins.................................................................................. 6
5 TPS65986..................................................................................................................... 7
6 TUSB564RNQ EVM Power ................................................................................................ 8
List of Tables
1 TUSB564 Configuration Pins............................................................................................... 3
2 Configuration Pin Level Definitions........................................................................................ 3
3 USB 3.1 EQ Settings........................................................................................................ 3
4 DisplayPort™ EQ Settings ................................................................................................. 4
5 Bill of Materials............................................................................................................... 9
Trademarks
USB Type-C is a trademark of USB Implementers Forum.
DisplayPort is a trademark of Video Electronics Standards Association.
VESA is a registered trademark of Video Electronics Standards Association.
All other trademarks are the property of their respective owners.

DP Source
USB Host TUSB1046EVM
USBDP
USB Type-C
USB Hub / Device
TUSB564RNQEVM
USB DP
USB Type-C
DP-Branch / Sink
Introduction www.ti.com
2SLLU288–March 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
1 Introduction
The TUSB564 device is a USB Type-C™ / VESA®DisplayPort™ (DP) alternate mode redriving switch
supporting USB data rates up to 5 Gbps for a USB Type-C upstream facing port (UFP).
2 TUSB564RNQ EVM
Figure 1 shows the TUSB564RNQ EVM.
Figure 1. TUSB564RNQ EVM
The TUSB564RNQ EVM can be used with an Alternate mode USB Type-C source such as the TUSB1046
EVM and/or USB or DisplayPort USB Type-C Host system to evaluate the USB Type-C implementation.
Figure 2 shows a typical test setup.
Figure 2. Test Board Setup
The TUSB564RNQ EVM has a legacy Type-A USB receptacle to connect to a USB hub or device and a
DisplayPort receptacle to connect to DisplayPort sink. The EVM uses TI's TPS65986 device for USB
Type-C PD control and to configure the TUSB564.

www.ti.com TUSB564RNQ EVM Configuration
3
SLLU288–March 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
3 TUSB564RNQ EVM Configuration
This section provides the configuration options available in the TUSB564RNQ EVM.
3.1 TUSB564RNQ EVM Default Configuration
Table 1 lists the default configuration pins for the TUSB564 device. Configuration settings may need to be
optimized depending on the amount of loss of each channel in the system. The EVM is configured to
GPIO mode by default. If I2C configuration is desired, JMP7 (I2C_EN) shunt must be changed to shunt
pins 2-3 (VCC).
Table 1. TUSB564 Configuration Pins
Reference
Designator JMP Control Configuration
JMP1 Downstream EQ1 SHUNT on pin 2-4 (R – 20k to GND)
JMP2 Downstream EQ0 SHUNT on pin 2-4 (R – 20k to GND)
JMP3 Downstream SSEQ1 SHUNT on pin 2-4 (R – 20k to GND)
JMP4 Downstream SSEQ0 SHUNT on pin 2-4 (R – 20k to GND)
JMP5 DP EQ1 SHUNT on pin 2-4 (R – 20k to GND)
JMP6 DP EQ0 SHUNT on pin 2-4 (R – 20k to GND)
JMP7 I2C_EN SHUNT on pin 1-2 (GND)
J1 FLIP No SHUNT
J2 CTL0 No SHUNT
J3 CTL1 No SHUNT
J4 EN SHUNT on pin 1-2 (PU)
3.2 TUSB564 Equalization Control
Equalization (EQ) can be controlled through I2C or pin-strapping (see Table 2). Each TUSB564 receiver
lane has individual controls for receiver equalization. Table 3 and Table 4 detail the gain values for each
available combination for downstream, upstream, and all DisplayPort configurations.
Table 2. Configuration Pin Level Definitions
Level Settings
0Option 1: Tie 1 kΩ5% to GND.
Option 2: Tie directly to GND.
R Tie 20 kΩ5% to GND.
F Float (leave pin open)
1Option 1: Tie 1 kΩ5% to VCC.
Option 2: Tie directly to VCC.
Table 3. USB 3.1 EQ Settings
USB 3.1 Downstream Facing Ports USB 3.1 Upstream Facing Ports
EQ1 Pin Level EQ1 Pin Level EQ Gain at 2.5 GHz
(dB) SSEQ1 Pin Level SSEQ1 Pin Level EQ Gain at 2.5 GHz (dB)
0 0 –2.4 0 0 –0.9
0 R –1.3 0 R 0.2
0 F –0.4 0 F 1.2
0 1 0.7 0 1 2.2
R 0 1.5 R 0 3.1
R R 2.5 R R 4.0
R F 3.2 R F 4.8
R 1 4.0 R 1 5.6
F 0 4.8 F 0 6.3

TUSB564RNQ EVM Configuration www.ti.com
4SLLU288–March 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
Table 3. USB 3.1 EQ Settings (continued)
USB 3.1 Downstream Facing Ports USB 3.1 Upstream Facing Ports
EQ1 Pin Level EQ1 Pin Level EQ Gain at 2.5 GHz
(dB) SSEQ1 Pin Level SSEQ1 Pin Level EQ Gain at 2.5 GHz (dB)
F R 5.5 F R 7.0
F F 6.0 F F 7.5
F 1 6.6 F 1 8.1
1 0 7.1 1 0 8.5
1 R 7.6 1 R 9.1
1 F 8.0 1 F 9.5
1 1 8.5 1 1 9.9
Table 4. DisplayPort™ EQ Settings
All DisplayPort Lanes
DPEQ1 Pin Level DPEQ0 Pin Level EQ Gain at 5 GHz (dB)
0 0 –0.3
0 R 1.6
0 F 3.0
0 1 4.4
R 0 5.4
R R 6.5
R F 7.3
R 1 8.1
F 0 8.9
F R 9.5
F F 10.0
F 1 10.6
1 0 11.0
1 R 11.4
1 F 11.8
1 1 12.1
3.3 Power
The EVM is designed to operate off of the VBUS from a USB host connected through USB Type-C (P2). A
5-V external power is applied through J8 only if stand-alone operation is desired.
If testing DisplayPort only, or if bypassing VBUS power, the EVM must be powered through J8 (a 5-V, 1-A
input).

CC1
CC2
C_USB_TN
C_USB_TP
C_USB_BP
C_USB_BN
SBU2
SBU1
EQ0
EQ1
I2C_EN
USB_N
USB_P
CTL1
TPS_SBU1
TPS_SBU2
TPS_AUX_P
TPS_AUX_N
FLIP/SCL
CTL0/SDA
I2C_SCL
I2C_SDA
SSEQ1
DPEQ1
SSEQ0/A0
DPEQ0/A1
HPD
EN
3P3VCC
VBUS
1064_VCC
1064_VCC
1064_VCC
1064_VCC
VBUS_DS
3P3VCC
3P3VCC
3P3VCC
P2
USB3 Type A Receptacle
VBUS
1
USB2_DM
2
USB2_DP
3
GND
4
SS_RX_N
5
SS_RX_P
6
GND_Drain
7
SS_TX_N
8
SS_TX_P
9
Shield1 10
Shield2 11
C12 100nF
R9
1M
R6 0
R14
100k DNI
C47
10nF
C22
1uF
C19 220nF
U3
TPD4E05U06
D1+
1
D1-
2
GND
3
D2+
4
D2-
5NC6 6
NC7 7
GND 8
NC9 9
NC10 10
R16 0 DNI
R8 0
C8 470nF
C48
10nF
U4
TPD4E05U06
D1+
1
D1-
2
GND
3
D2+
4
D2-
5NC6 6
NC7 7
GND 8
NC9 9
NC10 10
C14 100nF
C2
470nF
R2 0
P1
JAE DX07S024JJ2
GND A1
SSTXP1 A2
SSTXN1 A3
VBUS A4
CC1 A5
DP1 A6
DN1 A7
SBU1 A8
VBUS A9
SSRXN2 A10
SSRXP2 A11
GND A12
GND B1
SSTXP2 B2
SSTXN2 B3
VBUS B4
CC2 B5
DP2 B6
DN2 B7
SBU2 B8
VBUS B9
SSRXN1 B10
SSRXP1 B11
GND B12
CHASSIS
1
CHASSIS
2
CHASSIS
3
CHASSIS
4
CHASSIS
5
CHASSIS
6
C23
1uF
U2
TPD4E05U06
D1+
1
D1-
2
GND
3
D2+
4
D2-
5NC6 6
NC7 7
GND 8
NC9 9
NC10 10
C16 100nF
R17 0 DNI
R1
10k DNI
R15 0 DNI
C13 470nF
C24
100nF
C11 470nF
C3
470nF
C18 100nF
C25
100nF
C5 100nF
C4 220nF
P3
Display_Port_Connector_Source
ML_0p
1
GND1
2
ML_0n
3
ML_1p
4
GND2
5
ML_1n
6
ML_2p
7
GND3
8
ML_2n
9
ML_3p
10
GND4
11
ML_3n
12
CAD
13
GND5
14
AUX_p
15
GND6
16
AUX_n
17
HPD
18
RTN
19
DP_PWR
20
GND7 21
GND8 22
GND9 23
GND10 24
R18 0 DNI
C15 470nF
R12
1M DNI
C20 100nF
C7 100nF
R3 0 DNI
C1 100nF
R83
2M
C6 220nF
R10
5M
R4
100k DNI
R5 0 DNI
C26
10nF
C10 100nF
R13
1M DNI
R7 0
FB2
26 @ 100MHZ
C21
1uF
U1
TUSB564
NC 1
DPEQ1 2
SSEQ1 3
SSRXp 4 SSRXn 5
VCC 6
SSTXp 7 SSTXn 8 TX1p
9
TX1n
10
EQ0
11
RX1p
12
RX1n
13
EQ1
14
RX2n
15
RX2p
16
I2C_EN
17
TX2n
18
TX2p
19
VCC
20
FLIP/SCL
21
CTL0/SDA
22
CTL1
23
SBU1
24
SBU2
25
AUXp
26
AUXn
27
VCC
28
EN 29
DP3N 30
DP3P 31
HPDIN 32
DP2N 33
DP2P 34
DPEQ0/A1 35
DP1N 36
DP1P 37
SSEQ0/A0 38
DP0N 39
DP0P 40
PAD/GND 41
C45
10nF
R84
2M
C17 220nF
U5
TPD4E05U06
D1+
1
D1-
2
GND
3
D2+
4
D2-
5NC6 6
NC7 7
GND 8
NC9 9
NC10 10
R11 0
C46
10nF
C9 100nF
DP0P
DP0N
DP1P
DP1N
DP2P
DP2N
DP3P
DP3N
AUXp
AUXn
HPD
CC1
CC2
SBU1
SBU2
TX1P
TX1N
RX2P
RX2N
TX2P
TX2N
RX1P
RX1N
TX1P
TX1N
TX2P
TX2N
RX1P
RX1N
RX2N
RX2P
SSRXN
SSRXP
SSTXP
SSTXN
SSRXP
SSRXN
SSTXP
SSTXN
DP0P
DP0N
DP1P
DP1N
DP2P
DP2N
DP3P
DP3N
AUXn
AUXp
TX1P
TX1N
RX1P
RX1N
TX1P
TX1N
RX1P
RX1N
TX2P
TX2N
RX2P
RX2N RX2N
RX2P
TX2N
TX2P
CC1
CC2
SBU1
SBU2
CC1
CC2
SBU1
SBU2
C_USB_BP
C_USB_BN
C_USB_TP
C_USB_TN
C_USB_BP
C_USB_BN
C_USB_TP
C_USB_TN
SBU1
SBU2
AUXp
AUXn
CONFIG1
CONFIG2
SBU1
SBU2
HPDIN HPDIN
www.ti.com TUSB564RNQ EVM Schematics and Bill of Materials
5
SLLU288–March 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
4 TUSB564RNQ EVM Schematics and Bill of Materials
4.1 Schematics
The section provides schematics as supporting reference information.
Figure 3. TUSB564RNQ EVM Main Schematic

EQ0EQ1
FLIP/SCL
SSEQ1 SSEQ0/A0
CTL0/SDA
DPEQ1 DPEQ0/A1
CTL1
EN
I2C_EN
1064_VCC1064_VCC1064_VCC
1064_VCC
1064_VCC 1064_VCC
1064_VCC
1064_VCC 1064_VCC
1064_VCC1064_VCC
JMP4
4 Pin-T Berg Jumper
1
2
3
4
R20 1K
R24 1K
R23 20K
R35
1K
JMP6
4 Pin-T Berg Jumper
1
2
3
4
R19 1K
R25 1K
J2
HDR3X1 M .1
1
2
3
R29 1K
R26 20K
J1
HDR3X1 M .1
1
2
3
R36 20K
R28
1K
R30 1K
J3
HDR3X1 M .1
1
2
3
R31 20K
R34 1K
R27 20K
R21 20K
JMP2
4 Pin-T Berg Jumper
1
2
3
4
R32 20K
R22
1K
J4
HDR3X1 M .1
1
2
3
R33
1K
JMP3
4 Pin-T Berg Jumper
1
2
3
4
JMP1
4 Pin-T Berg Jumper
1
2
3
4
JMP7
4 Pin-T Berg Jumper
1
2
3
4
JMP5
4 Pin-T Berg Jumper
1
2
3
4
TUSB564RNQ EVM Schematics and Bill of Materials www.ti.com
6SLLU288–March 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
Figure 4. TUSB564RNQ EVM Configuration Pins

SPI Programming Header
SILKSCREEN:
SPI
TPS65982
CC1
CC2
C_USB_TP
C_USB_TN
C_USB_BP
C_USB_BN
USB_P
USB_N
FLIP/SCL
CTL0/SDA
CTL1
HPD
TPS_SBU1
TPS_SBU2
TPS_AUX_P
TPS_AUX_N
I2C_SCL
I2C_SDA
LDO_3P3
LDO_3P3
VOUT_3P3
LDO_3P3
LDO_3P3
TPS65986_3P3V
VBUS
VBUS_DS
SYS_PWR
VBUS
TPS65986_3P3V
VDDIO
C27
0.22uF
C36
1uF
R58
3.3k
SW1
4-POS 50-MIL SMT
1
1
2
2
3
3
4
455
66
77
88
R38 0
C30
10uF
C32
1uF
R60 100k
C39
0.01uF
R64
1k
R72 3.3k
R50
1M
C37
0.1uF
R41 0
D3
1
1
2
2
R59
3.3k
C50
10uF
R87 100k
C33
1uF
J5
HDR3X2 .1X.1
1
3
5
2
4
6
R45 1M
C51
1uF 25V
C38
0.1uF
R43 0
R46 0 DNI
1
10
2
3
JMP8
Header 5x2
R73 3.3k
R74 3.3k
R51
1M
R47 1M
J7
Header 5x2 0.1" Shroud RA thru-hole
2
4
6
8
10
1
3
5
7
9
R66 0
R52 100k DNI
R44 0
C34
1uF
R61
1k
U6
TPS65986
GND
A1
LDO_1V8D
A2
SPI_CLK
A3
SPI_MISO
A4
GND
A5
PP_HV1
A6
PP_HV2
A7
PP_HV3
A8
NC3 A9
SENSEN A10
PP_5V0_2
A11
VDDIO
B1
GPIO0 B2
SPI_SSZ
B3
SPI_MOSI
B4
GND
B5
NC1
B6
PP_HV4
B7
GND
B8
NC2 B9
SENSEP B10
PP_5V0_1
B11
I2C_IRQ1Z
C1
GPIO1 C2
GPIO4
C10
PP_5V0_3
C11
I2C_SDA1
D1
I2C_SCL1
D2
DBG_CTL2
D5
HRESET
D6
GPIO7 D7
GND
D8
GPIO2 D10
PP_5V0_4
D11
LDO_BMC
E1
UART_TX
E2
DBG_CTL1
E4
GND
E5
GND
E6
GND
E7
GND
E8
GPIO5
E10
MRESET E11
I2C_ADDR
F1
UART_RX
F2
SWD_DAT
F4
GND
F5
GND
F6
GND
F7
GND
F8
BUSPOWERZ F10
RESETZ F11
LDO_3V3
G1
R_OSC G2
SWD_CLK
G4
GND
G5
GND
G6
GND
G7
GND
G8
GPIO6 G10
GPIO3 G11
VIN_3V3
H1
VOUT_3V3
H2
GND
H4
GND
H5
GPIO8 H6
SS H7
GND
H8
PP_CABLE
H10
VBUS1 H11
AUX_P
J1
AUX_N
J2
VBUS2 J10
VBUS3 J11
LDO_1V8A
K1
DEBUG2
K2
DEBUG4
K3
NC4
K4
USB_RP_N
K5
C_USB_TP K6
C_USB_BP K7
C_SBU1 K8
RPD_G1 K9
RPD_G2 K10
VBUS4 K11
GND
L1
DEBUG1
L2
DEBUG3
L3
GND
L4
USB_RP_P
L5
C_USB_TN L6
C_USB_BN L7
C_SBU2 L8
C_CC1 L9
C_CC2 L10
NC L11
C49
10uF
R49 1M
R62
1k
R67 3.3k
R40 0
R71 3.3k DNI
R42 0
C28
330pF
R37 0
R48 1M
R70 0
R39 15k 0.1%
J6
HDR2X2 M .1X.1
1
3
2
4
C35
1uF
R57
10k
R63
1k
C29
330pF
R68 3.3k
U7
W25Q80
/CS
1
DO
2
/WP 3
GND 4
VCC 8
CLK
6DI
5
/HOLD
7
C31
1uF
R53 100k
GPIO5
I2C_IRQ1Z
I2C_SCL1
LCO_1P8VD
LCO_1P8VA
LDO_BMC
I2C_SCL1
I2C_SDA1
SPI_MISO
SPI_CLK SPI_MOSI
SPI_SSZ
I2C_ADDR
SPI_SSZ
SPI_MISO
SPI_MOSI
SPI_CLK
DBG_CTL2
DBG_CTL1
SPI_SSZ
SPI_MISO
SPI_MOSI
SPI_CLK
SPI_HOLD#
SPI_WP#
CTL0/SDA
FLIP/SCL
HPD
GPIO6
CTL1
GPIO3
GPIO5
GPIO7
GPIO8 GND
GPIO3
GPIO6
GPIO7
GPIO8
I2C_ADDR
DBG_CTL1
DBG_CTL2
CC1
CC2
VBUS
VBUS_DS
SYS_PWR
I2C_SDA1
LCO_1P8VD
www.ti.com TUSB564RNQ EVM Schematics and Bill of Materials
7
SLLU288–March 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
Figure 5. TPS65986

3.3V REGULATOR
DOWNSTREAM PORT/PP_5V POWER SWITCH
5V INPUT
+5V / Max 3A Input
SYS_PWR
SYS_PWR
VBUS_DS
3P3VCC
1064_VCC TPS65986_3P3V
SYS_PWR
VBUS
VBUS
VDDIO LDO_3P3
R82
0 DNI
T
S
J8
2.1mm x 5.5mm
1
2
3
R75
0
D4
R77
330
FB1
26 @ 100MHZ
R76
0
R78
330
U9
TPS7A4501
SHDN/
1
IN
2
GND
3
OUT 4
ADJ 5
GND
6
R80
3.9K
R85 0
C41
10uF
R86 0 DNI
C44
10uF
R81
1.2K
D2
LED Green
R79
0 DNI
C42
10uF
C40
22uF
U8
TPS7A4533
GND
6
IN
2
GND
3
SENSE 5
OUT 4
SHDN/
1
PMEG3050EP, 115
D1
1
2
C43
10uF
TUSB564RNQ EVM Schematics and Bill of Materials www.ti.com
8SLLU288–March 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
Figure 6. TUSB564RNQ EVM Power

www.ti.com TUSB564RNQ EVM Schematics and Bill of Materials
9
SLLU288–March 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
4.2 Bill of Materials
Table 5 lists the bill of materials.
Table 5. Bill of Materials
Item Qty Reference Part Footprint Manufacturer Manufacturer Part Number Description
1 10 C1,C5,C7,C9,C10,C12,C14,
C16,C18,C20 100 nF c0201 Murata GRM033R61A104KE15D CAP CER, 0.1-µF, 10-V X5R 0201
2 6 C2,C3,C8,C11,C13,C15 470 nF c0201 Murata GRM033R60J474KE90D CAP CER, 0.47-µF, 6.3-V X5R 0201
3 4 C4,C6,C17,C19 220 nF c0201 Murata GRM033R60G224ME15D CAP CER, 0.22-µF, 4-V, X5R 0201
4 9 C21,C22,C23,C31,C32,C33,
C34,C35,C36 1 µF c0402 Murata GRM155R60J105ME19D CAP CER, 1-µF, 6.3-V X5R 0402
5 2 C24,C25 100 nF c0402 Murata GRM155R61A104KA01D CAP CER, 0.1-µF, 10-V X5R 0402
6 5 C26,C45,C46,C47,C48 10 nF c0402 Murata GRM155R71C103KA01D CAP CER, 10000-pF, 16-V X7R 0402
7 1 C27 0.22 µF c0402 Murata GRM152R61A224KE19D CAP CER, 0.22-µF, 10-V X5R 0402
8 2 C28,C29 330 pF c0402 Murata GRM1555C1E331JA01D CAP CER, 330-pF, 25-V C0G/NP0 0402
9 5 C30,C43,C44,C49,C50 10 µF c0603 Murata GRM188R61E106MA73D CAP CER, 10-µF, 25-V X5R 0603
10 2 C37,C38 0.1 µF c0402 Murata GRM155R61A104KA01D CAP CER, 0.1-µF, 10-V X5R 0402
11 1 C39 0.01 c0402 Murata GRM155R71C103KA01D CAP CER, 10000-pF, 16-V X7R 0402
12 1 C40 22 µF c1206 Murata GRT31CR61E226ME01L CAP CER, 22-µF, 25-V X5R 1206
13 2 C41,C42 10 µF c1206 Murata GRM319R61E106KA12D CAP CER, 10-µF, 25-V X5R 1206
14 1 C51 1 µF, 25 V c0603 Murata GRM185R61E105KA12D CAP CER, 1-µF, 25-V X5R 0603
15 1 D1 SCHOTTKY DO-214AA NXP PMEG3050EP,115 DIODE SCHOTTKY 30-V 5-A SOD128
16 1 D2 LED green 805 Lumex LTST-C170KGKT LED GREEN CLEAR 0805 SMD
17 1 D3 TPD1E10B06 DPY0001AA Texas Instruments TPD1E10B06DPYR Schottky
18 1 D4 LED green 0805 805 Lumex LTST-C170KGKT LED GREEN CLEAR 0805 SMD
19 2 FB1,FB2 26 at 100 MHz 603 Murata BLM18SG260TN1D FERRITE BEAD 26 Ω0603 1LN
20 7 JMP1A,JMP2A,JMP3A,JMP
4A,JMP5A,JMP6A,JMP7A 4 Pin-T Berg Jumper BERGSTIK II .100" SR STRAIGHT AMP 68000-103HLF 3 Positions Header Connector 0.100" (2.54 mm) Through-Hole Gold or Gold, GXT™
21 7 JMP1B,JMP2B,JMP3B,JMP
4B,JMP5B,JMP6B,JMP7B BERGSTIK II .100" SR STRAIGHT AMP 68000-101HLF 1 Positions Header Connector 0.100" (2.54 mm) Through-Hole Gold or Gold, GXT™
22 1 JMP8 Header 5 × 2 HDR_THVT_2x5_100 FCI 68021-210HLF CONN HEADER 10-POS .100 R/A 15AU
23 4 J1,J2,J3,J4 HDR3X1 M .1 HDR_THVT_1x3_100_M 3M 961103-6404-AR CONN HEADER VERT SGL 3-POS GOLD
24 1 J5 HDR3X2 .1X.1 HDR_THVT_2x3_100_M Harwin M20-9980345 DIL VERTICAL PC TAIL PIN HEADER
25 1 J6 HDR2X2 M .1X.1 HDR_THVT_2x2_100 Amphenol FCI 67997-404HLF CONN HEADER 4-POS .100 STR TIN
26 1 J7 Header 5 × 2 0.1"
Shroud RA through-
hole
HDR_THRT_2X5_ 100 Amphenol FCI 67997-410HLF CONN HEADER 10-POS .100 STR TIN
27 1 J8 2.1 mm × 5.5 mm PJ-202AH CUI Inc. PJ-202AH CONN PWR JACK 2-mm × 5.5-mm KINKED PIN
28 2 LB1,LB2 THD-47-478-10 Rectangle Brady THD-47-478-10 LB1 = "HSDC025A-001", LB2 = "TUSB564RNQEVM"
29 1 P1 JAE DX07S024JJ2 USB-C_SMRT_DX07S024JJ2 JAE DX07B024JJ2 CONN RCPT USB 3.1 USB Type-C BRD EDGE
30 1 P2 USB3 Type-A
receptacle USB3_TYPEA AMP GSB4111312HR USB 3.1 Type-A Connector
31 1 P3 Display_Port_
Connector_Source CON_DP_SD-47272-001 Molex Inc. 472720001 CONN RCPT 20-POS UDI R/A SMD

TUSB564RNQ EVM Schematics and Bill of Materials www.ti.com
10 SLLU288–March 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
Table 5. Bill of Materials (continued)
Item Qty Reference Part Footprint Manufacturer Manufacturer Part Number Description
32 0 R1 10k DNI r0402 Panasonic Electronic
Components ERJ-2GEJ103X RES SMD 10 kΩ5% 1/10W 0402
33 11 R2,R6,R7,R8,R11,R41,R43,
R44,R66,R70,R85 0 r0402 Panasonic Electronic Components ERJ-2GE0R00X RES SMD 0-ΩJUMPER 1/10W 0402
34 0 R3,R5,R15,R16,R17,R18,R
46,R86 0 DNI r0402 Panasonic Electronic Components ERJ-2GE0R00X RES SMD 0-ΩJUMPER 1/10W 0402
35 0 R4,R14,R52 100k DNI r0402 Panasonic Electronic
Components ERJ-2GEJ104X RES SMD 100 kΩ5% 1/10W 0402
36 7 R9,R45,R47,R48,R49,R50,
R51 1M r0402 Panasonic Electronic Components ERJ-2GEJ105X RES SMD 1 MΩ5% 1/10W 0402
37 1 R10 5M r0402 Ohmite HVC0402T5004JET RES SMD 5 MΩ5% 1/20W 0402
38 0 R12,R13 1M DNI r0402 Panasonic Electronic
Components ERJ-2GEJ105X RES SMD 1-MΩ5% 1/10W 0402
39 15 R19,R20,R22,R24,R25,R28,
R29,R30,R33,R34,R35,R61,
R62,R63,R64
1k r0402 Panasonic Electronic
Components ERJ-2GEJ102X RES SMD 1 kΩ5% 1/10W 0402
40 7 R21,R23,R26,R27,R31,R32,
R36 20K r0402 Panasonic Electronic Components ERJ-2RKF2001X RES SMD 20 kΩ1% 1/10W 0402
41 2 R37,R38 0 r0201 Panasonic Electronic
Components ERJ-1GN0R00C RES SMD 0-ΩJUMPER 1/20W 0201
42 1 R39 15k 0.1% r0402 Panasonic Electronic
Components ERA-2AEB153X RES SMD 15 kΩ0.1% 1/16W 0402
43 2 R40,R42 0 r0402 Panasonic Electronic
Components ERJ-2GE0R00X RES SMD 0-ΩJUMPER 1/10W 0402
44 3 R53,R60,R87 100k r0402 Panasonic Electronic
Components ERJ-2GEJ104X RES SMD 100 kΩ5% 1/10W 0402
45 1 R57 10k r0402 Panasonic Electronic
Components ERJ-2GEJ103X RES SMD 10 kΩ5% 1/10W 0402
46 7 R58,R59,R67,R68,R72,R73,
R74 3.3k r0402 Panasonic Electronic Components ERJ-2GEJ332X RES SMD 3.3 kΩ5% 1/10W 0402
47 0 R71 3.3k DNI r0402 Panasonic Electronic
Components ERJ-2GEJ332X RES SMD 3.3 kΩ5% 1/10W 0402
48 2 R75,R76 0 r1206 Panasonic Electronic
Components ERJ-8GEY0R00V RES SMD 0-ΩJUMPER 1/4W 1206
49 2 R77,R78 330 r0402 Panasonic Electronic
Components ERJ-2GEJ331X RES SMD 330 Ω5% 1/10W 0402
50 0 R79,R82 0 DNI r0805 Panasonic Electronic
Components ERJ-6GEY0R00V RES SMD 0-ΩJUMPER 1/8W 0805
51 1 R80 3.9K r0402 Panasonic Electronic
Components ERA-2AEB392X RES SMD 3.9 kΩ0.1% 1/16W 0402
52 1 R81 1.2K r0402 Panasonic Electronic
Components ERA-2AEB122X RES SMD 1.2 kΩ0.1% 1/16W 0402
53 2 R83,R84 2M r0402 Panasonic Electronic
Components ERJ-2GEJ205X RES SMD 2 MΩ5% 1/10W 0402
54 4 SCRW1,SCRW2,SCRW3,S
CRW4 NY PMS 440 005 PH Screw B&F Fastener NY PMS 440 005 PH 40 × .5-inch nylon
55 8 SHNT1,SHNT2,SHNT3,SHN
T4,SHNT5,SHNT6,SHNT7,S
HNT8
QPC02SXGN-RC 0.1 Sullins Connector Solutions QPC02SXGN-RC CONN JUMPER SHORTING .100" GOLD

www.ti.com TUSB564RNQ EVM Schematics and Bill of Materials
11
SLLU288–March 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
TUSB564RNQ Evaluation Module
Table 5. Bill of Materials (continued)
Item Qty Reference Part Footprint Manufacturer Manufacturer Part Number Description
56 4 STDOFF1,STDOFF2,STDO
FF3,STDOFF4 1902E Standoff Keystone 1902E 1-inch nylon
57 1 SW1 4-POS 50-MIL SMT sw_smvt_dip_4pos_8 C&K(ITT-CANNON) TDA04H0SB1R SWITCH SLIDE DIP SPST 25MA 24 V
58 1 U1 TUSB564 RNQ0040A Texas Instruments TUSB564RNQ
59 4 U2,U3,U4,U5 TPD4E05U06 DQA Texas Instruments TPD4E05U06DQAR TVS DIODE 5.5 VWM 14VC 10SON
60 1 U6 TPS65986 ZQZ_BGA_96 Texas Instruments TPS65986ABZQZR IC PD CTLR USB Type-C 96 BGA
61 1 U7 W25Q80 SOIC_8_197x157_50 WINBOND W25Q80DVSNIG IC FLASH 8Mb 104-MHz 8SOIC
62 1 U8 TPS7A4533 DCQ_PDSO_6 Texas Instruments TPS7A4533DCQR IC REG LINEAR 3.3-V 1.5-A SOT223-6
63 1 U9 TPS7A4501 DCQ_PDSO_6 Texas Instruments TPS7A4501DCQT IC REG LINEAR ADJ SOT223-6

STANDARD TERMS FOR EVALUATION MODULES
1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or
documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance
with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License
Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by
neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have
been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications
or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control
techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.
User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)
business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.
2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit
User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty
period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or
replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be
warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3Regulatory Notices:
3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:
FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software
associated with the kit to determine whether to incorporate such items in a finished product and software developers to write
software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or
otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition
that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.
Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must
operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the
instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs
(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):
1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/
/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
3.4 European Union
3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):
This is a class A product intended for use in environments other than domestic environments that are connected to a
low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.
4EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.

6. Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT
LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL
FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT
NOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE
SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BE
CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR
INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE
EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR
IMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.
7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLY
WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL
THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8. Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR
REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,
OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF
USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI
MORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HAS
OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDED
HEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR IN
CONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAR
EVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE
CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated

IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your non-
compliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated