Toshiba IK-HD2E User manual

CAMERA CONTROL UNIT
IK-HD2E
INSTRUCTION MANUAL
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party responsible for compliance to
Part 15 of the FCC Rules.
Canada ICES-003 Compliance Lable:
CAN ICES-3 A/NMB-3A
Following information is only for EU-member states:
In residential areas this product may cause radio interference, therefore this product must not be used
in residential areas.
This manual is made from recycled paper.
For Customer Use
Enter below the Serial No.
which is located on the
bottom of the cabinet. Retain
this information for future ref-
erence.
Model No.: IK-HD2E
Serial No.:
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about the take-
back and recycling of this product, please contact your supplier where you purchased the
product or consult.

2
SAFETY PRECAUTIONS
Safety icons
This manual contains safety instructions that must be observed in order to avoid potential
hazards that could result in personal injuries, damage to your equipment, or loss of data.
These safety cautions have been classified according to the seriousness of the risk, and th
e
icons highlight these instructions as follows:
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
Stop operation immediately if any abnormality or defect occurs.
Use during an abnormal condition; such as emitting smoke, burning odors, damage
from dropping, invasion of foreign objects, etc. may result in fire and/or electrical
shock. Immediately disconnect the power source and contact your dealer.
Avoid installing in a shower room or a bathroom.
This may result in fire and/or electrical shock.
Do not operate in placeswhere the product may get wet.
This may result in fire and/or electrical shock.
Do not repair, disassemble and/or modify by yourself.
This may result in fire and/or electrical shock. Always be sure to contact your
dealer for internal repair, check and cleaning of the product.
Use the specified power supply.
Otherwise, fire or electrical shock may occur.
Do not place anything on top of the unit.
Foreign materials, such as metals or liquids, getting into the product may result
in fire and/or electrical shock.
Do not put the product on an unstable, slanted or vibrating surface.
The product dropping or falling may result in serious injury.
Do not touch the product or any connection cablesduring a thunder-
storm.
This may result in electrical shock.

3
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the
The following description is described the state that the suitable camera head is connected to this
camera control unit.
user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-
tional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including
but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the
purchase price of the product.
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright
holder. Please also note that transfer of an image or file covered by copyright is restricted to use
within the scope permitted by the Copyright Law.
Protection of Personal Information
Note the following instructionswhen installing.
5Do not cover the product with any material.
5Do not place the product on any inflammable material such as a carpet or
5o not place the product in a confined space, as this may cause heat to
build up inside the product.
blanket.
Failure to follow the above cautions may result in fire.
Do not place the product in direct sunshine and/or high temperature.
Temperature build up inside the product may result in fire.
Avoid placing in humid, smoky, or dusty places.
This may result in fire and/or electrical shock.
Do not point the lensdirectly at the sun and/or intensive light such asdi-
rect sunlight, etc.
Focusing of the light may result in eye injury and/or fire.
Ask your dealer to perform a periodical check and internal cleaning (approx.
once every five years).
Dust inside the product may result in fire. For check and cleaning cost, please
consult your dealer.
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent of the person may be required.

4
1CAUTIONS ON USE AND INSTALLATION ............................................
2COMPONENTS .......................................................................................
3ITEMS CONTROLLED BY THE ON SCREEN DISPLAY........................
4NAMES AND FUNCTIONS......................................................................
5CONNECTION........................................................................................
5.1 Standard Connection ..................................................................................................
5.2 Cautions on Connection..............................................................................................
5.3 Connection on Back Panel..........................................................................................
5.4 A Connector Pin Assignments ....................................................................................
6OPERATION...........................................................................................
6.1 Automatic Black Balance ............................................................................................
6.2 White Balance.............................................................................................................
6.3 Scene File ...................................................................................................................
6.4 Gain.............................................................................................................................
6.5 Shading Correction .....................................................................................................
7MODE SETTING BY THE ON SCREEN DISPLAY ................................
7.1 Using the Menus .........................................................................................................
7.2 Menus .........................................................................................................................
(1) SHUTTER (Electronic shutter) ....................................................................................
(1.1) Changing the setting in AUTO mode...................................................................
(1.2) Changing the setting in MANUAL mode..............................................................
(1.3) Changing the setting in SS (Synchro. Scan) mode .............................................
(2) GAIN (Video gain) .......................................................................................................
(2.1) Changing maximum gain in AUTO (Automatic gain control) mode ....................
(2.2) Changing gain in MANUAL mode........................................................................
(3) WHT BAL (White Balance) ..........................................................................................
(3.1) Changing the setting in AWB (Automatic White Balance) mode ........................
(3.2) Changing the setting in ATW (Automatic Tracking White balance) mode .........
(3.3) Changing gain in MANUAL mode .......................................................................
(4) PROCESS ..................................................................................................................
(4.1) Changing gamma correction ON/OFF ................................................................
(4.2) Changing gamma correction level.......................................................................
(4.3) Changing black gamma correction level..............................................................
6
6
7
8
9
9
10
10
10
11
11
12
14
14
15
16
16
17
17
18
20
20
21
21
21
22
22
23
24
25
25
25
26
TABLE OF CONTENTS
Limitation of Usage
The product is not designed for any “critical applications.” “Critical applications” means life support
systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass
transit applications, military applications, homeland security applications, nuclear facilities or systems
or any other applications where product failure could lead to injury to persons or less of life or
catastrophic property damage. Accordingly, [Toshiba] disclaims any and all liability arising out of the
use of the product in any critical applications.
(4.4) Changing detail (outline) gain..............................................................................
(4.5) Changing pedestal ..............................................................................................
(4.6) Changing DNR(Digital Noise Reduction).............................................................
26
26
26
(5) MATRIX(Matrix color correction) .................................................................................
(5.1) Changing Matrix color correction ON/OFF ..........................................................
(5.2) Changing MATRIX setting ...................................................................................
27
27
27

5
(6) SYNC...........................................................................................................................
(6.1) INT screen ...........................................................................................................
(6.2) Changing EXT. setting ........................................................................................
28
28
28
(7) OPTION.......................................................................................................................
(7.1) Changing OUTPUT mode ..................................................................................
(7.2) Changing shading correction mode ....................................................................
(7.3) Changing manual shading correction mode ........................................................
(7.4) Changing RGB SYNC .........................................................................................
(7.5) Changing detail signal output ..............................................................................
29
29
29
29
30
30
(7.6) Changing RS232C baud rate ..............................................................................
(8) Setting USER area .....................................................................................................
30
(7.7) Changing OSD OUTPUT mode .......................................................................... 30
31
(2) External sync frequency range ....................................................................................
(3) Using the unit with external sync signal.......................................................................
(3.1) H (Horizontal) phase adjustment .........................................................................
7.4 Synchro. Scan Operation ............................................................................................
(1) Setting by 1H ...............................................................................................................
8BEFORE MAKING A SERVICE CALL....................................................
9SPECIFICATIONS..................................................................................
10 EXTERNAL APPEARANCE DIAGRAM..................................................
32
32
32
32
32
33
34
35
(9) Returning to factory settings .......................................................................................
7.3 External Sync ..............................................................................................................
(1) External sync signal input conditions...........................................................................
32
32
32

6
1 Camera Control Unit ............................................................................................... 1
2Accessories
aInstruction manual ........................................................................................ 1
2. COMPONENTS
1. CAUTIONS ON USE AND INSTALLATION
"Handling the unit.
"Do not shoot intense light.
If there is an intense light at a location on the
screen such as a spot light, a blooming and smear-
ing may occur. When intense light enters, vertical
stripes may appear on the screen. This is not a
malfunction. Ghosts may occur when there is an
intense light near the object. In this case, change
the shooting angle.
"Install the camera in a location free from noise.
If the camera or the cables are located near power
utility lines or a TV, etc. undesirable noise may ap-
pear on the screen. In such a case, try to change
the location of the camera or the cable wiring. "Moire
"Operating ambient temperature and humidity.
Do not use the camera in places where tempera-
ture and humidity exceed the specifications. Pic-
ture quality will deteriolate and internal parts may
be damaged.
Be particularly careful when using in places ex-
posed to direct sunlight. When shooting in hot
places, depending on the conditions of the object
and the camera (for example when the gain is in-
creased), noise in the form of vertical strips or
white dots may occur. This is not a malfunction.
"Handling of the camera head and protection
cap.
"When not using the camera for extended
periodsof time. "When cleaning the camera.
"Avoid using or storing the camera in the fol-
lowing places:
"Installation without a tripod.
Do not drop, jolt, or vibrate, as this may result in
damage to the unit and cause problems. Treat
the camera cables carefully to prevent cable
problems, such as breaks in the cable and loose
connections.
Keep the camera head and protection cap away
from children as they may pose a choking
hazard. The protection cap protects the image
sensing plane when the lens is removed from the
camera head, do not discard.
Unplug the power source before cleaning. Clean
with a soft dry cloth only. Do not use chemicals or
chemically treated cloths. Chemicals may damage
coatings and printed letters. When cleaning the
lens, use lens cleaning paper.
Before installing the camera head, make sure
that the location can withstand the total weight of
the camera head.
If this is not the case, reinforce the area to
prevent the unit from dropping, which may result
in damage to the unit or personal injury.
Places filled with highly flammable gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places containing chemicals (such as pesticides),
rubber or vinyl products for extended periods of
time.
Switch the control unit off and disconnect the
power supply.
A moire pattern is an interference pattern
generated when two repetitive line patterns
overlap. This is not a malfunction. Eliminating the
repetitive line patterns, or aligning the two
patterns, will eliminate the moire.
The following descriptions are for a camera head
"IK-HD1H" connected to this camera control unit.

7
3ITEMS CONTROLLED BY THE ON SCREEN DISPLAY
㻬㼗㼈㼐 㻤㼙㼄㼌㼏㼄㼅㼏㼈㻃㼖㼈㼏㼈㼆㼗㼌㼒㼑㼖 㻳㼕㼈㼖㼈㼗㻃㼙㼄㼏㼘㼈
㻋㻩㼄㼆㼗㼒㼕㼜㻃㼖㼈㼗㼗㼌㼑㼊㻌
Electronic shutter
MODE AUTO, MANUAL, SS MANUAL
AUTO level -100 – 0 – 100 0
AUTO peak/average 00 : 10 – 05 : 05 – 10 : 00 05 : 05
AUTO response speed 1 – 10 – 20 10
AUTO area
PRESET A, PRESET B, PRESET C, PRESET D,
PRESET E, USER
(USER area is possible to set in 64 zones)
PRESET A
MANUAL speed OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,
1/3000s, 1/5000s, 1/10000s, 1/30000s, 1/50000s OFF
Syncro. scan OFF, 1/1125H – 560/1125H OFF
Gain
MODE AUTO, MANUAL, OFF OFF
AUTO maximum gain 0dB to 18dB 18dB
MANUAL gain 0dB to 18dB 0dB
White balance
MODE AWB, ATW, MANUAL AWB
Color temperature 3200K, 5600K 3200K
AWB R PAINT -10 – 0 – 10 0
AWB B PAINT -10 – 0 – 10 0
AWB area
PRESET A, PRESET B, PRESET C, PRESET D,
PRESET E, USER
(USER area is possible to set in 64 zones)
PRESET A
ATW R PAINT -10 – 0 – 10 0
ATW B PAINT -10 – 0 – 10 0
MANUAL R GAIN -100 – 0 – 100 0
MANUAL B GAIN -100 – 0 – 100 0
Gamma correction ON, OFF ON
Gamma correction level -10 – 0 – 10 0
Black gamma correction level LOW, NORMAL, HIGH NORMAL
Detail gain -7(OFF) – 0 – 7 0
Master pedestal -200 – 0 – 200 0
Red pedestal -100 – 0 – 100 0
Blue pedestal -100 – 0 – 100 0
Digital noise reduction (DNR) ON, OFF OFF
Matrix color correction
Correction ON/OFF ON, OFF ON
R hue -15 – 0 – 15 0
R gain -15 – 0 – 15 0
G hue -15 – 0 – 15 0
G gain -15 – 0 – 15 0
B hue -15 – 0 – 15 0
B gain -15 – 0 – 15 0
Ye hue -15 – 0 – 15 0
Ye gain -15 – 0 – 15 0
Cy hue -15 – 0 – 15 0
Cy gain -15 – 0 – 15 0
Mg hue -15 – 0 – 15 0
Mg gain -15 – 0 – 15 0
Ext. Sync
H phase adjustment -650 – 0 – 650 0
OUTPUT Y/Pb/Pr, RGB Y/Pb/Pr
Shading correction mode SET, MANUAL, OFF OFF
Manual shading correction -128 – 0 – 127 0
RGB SYNC G, ALL ON, ALL OFF G
Detail signal output ON, OFF OFF
RS232C baud rate 9600bps, 19200bps 9600bps
OSD OUTPUT ALL ON, Analog, Digital ALL ON

8
3
4
2
1
12345
8796
Camera cable
for “IK-HD1H”
terminal
POWER switch
POWER LED
FILE button
GAIN button
DISP button
PAGE button
MENU UP
(SHD) button
MENU DOWN
(SHD) button
DATA UP
(AWB) button
DATA DOWN
(ABB) button
DC IN 12V terminal
REMOTE terminal
Y/G terminal
P
B /B terminal
P
R /R terminal
EXT. SYNC terminal
SYNC OUT terminal
HD-SDI terminal
KEY LOCK switch
FORMAT switch
4. NAMES AND FUNCTIONS
[Front]
[Rear]
䐖Camera cable for
“IK-HD1H” terminal
Where the camera cable for “IK-HD1H” is connected.
䐗POWER LED Illuminates to indicate the unit is powered on.
䐘POWER switch Turns power on or off.
䐙FILE button To switch the scene files.
䐚GAIN button To change the gain mode.
䐛DISP button Changes the display mode.
䐜PAGE button To switch and select menus.
䐝MENU UP䟺SHD䟻button To select the function to be confirmed or changed on the menu.
(Also used when performing auto shading correction.)
䐞MENU DOWN(SHD) button To select and confirm the function or to change the menu.
䐟DATA UP䟺AWB䟻button To change the value of the function selected by the MENU (UP/DOWN) button.
(Also used when performing an AWB.)
䐠DATA DOWN
䟺ABB䟻button
To change the value of the function selected by the MENU (UP/DOWN) button.
(Also used when performing an ABB.)

9
䐡DC IN 12V terminal Accept a DC power input (12V).
䐢Y/G terminal Outputs Y or G. (BNC connector)
䐣PB/B terminal Outputs PBor B. (BNC connector)
䐤PR/R terminal Outputs PRor R. (BNC connector)
䐥REMOTE terminal To connect to a RS-232C device for remote control function.
䐦EXT. SYNC terminal Used when the camera output signal is synchronized to an external signal.
(BNC connector)
䐧SYNC OUT terminal Output terminal for synchronization signal. (BNC connector)
䐨HD-SDI terminal Video signal output terminal for HD-SDI format video signal. (BNC connector)
䐩KEY LOCK switch Enables/disables buttons
FORMAT switch Switches between 59.94i and 50i.
䐙to 䐠.
Lens
(option)
IK-HD1H
䟺option䟻
Camera
Control unit
Camera Cable
for IK-HD2E
䟺option䟻
HD monitor
analog TV (option)
DC power supply
(option)
DC power supply
(option)
DC IN 12V
Y/PB/PR
Three Coaxial
Cables 75
(option)
䂿
IK-HD2E
5CONNECTION
5
5. 1 -1 Analog Connection
1 Standard Connection
Lens
(option)
IK-HD1H
䟺option䟻
Camera
Control unit
Camera Cable
for IK-HD2E
䟺option䟻
HD monitor
digital TV (option)
DC IN 12V
HD-SDI
One Coaxial
Cable 75
(option)
䂿
IK-HD2E
5. 1 -2 Digital Connection
* Please use a low conductor resistance cable for HD-SDI terminal.

10
DC IN 12V
1 +12V
2 +12V
3 GND
4 GND
REMOTE
1
2
3
4
5
6
7
8
9 NC
NC
NC
NC
GND
NC
RXD
TXD
NC
5 4 A Connector Pin Assignments
䝿Only use optional camera head model # IK-HD1H with this camera controller.
The use of another head may cause damage to the control unit and camera head.
䝿When connecting the camera cables, be sure to turn off the camera control unit and
any other equipment connected to it.
䝿For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA
approved ungrounded type AC adaptor with the specifications described below.
Power supply voltage 䠌12V DC 㼳10%
Current rating 䠌More than 1.5A
Ripple voltage 䠌Less than 50mV (p-p)
Connector 䠌HR10A-7P-4S by HIROSE electronics Co. Ltd
Pins 1, 2 䠌12V
Pins 3, 4 䠌GND
䝿If the securing screw on the connector of the camera cable loosens, noise may appear
on the screen. Be sure to tighten the connector completely.
Back panel view
52 Caution on Connection
53 Connection on Back Panel
3
4
2
1
12345
8796

11
䐖Refer to the item “5. CONNECTION”, connect the equipment correctly.
A camera head "IK-HD1H" needs to be connected to this camera control unit from this section on.
䐗Turn on the connected equipment and the camera.
䐘When using the camera for the first time and when replacing the camera cable and the camera head, be
sure to perform the ABB adjustment, refer to the item “6.1 Automatic Black Balance”.
䐙Aim the lens at the object, adjust the lens iris adjustment, focus adjustment, etc.
䐚Refer to the item “6.2 White Balance”, make the adjustment.
䐛Refer to the items “6.3 Scene File, 6.4 Gain, 7. MODE SETTING BY THE ON SCREEN DISPLAY”,
select the necessary items.
Black balance adjustment is necessary to get the correct black picture level.
䝿Close the lens iris.
䝿If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the
[DISP] button to disable the color bar pattern or the character display.
䝿Hold the [DATA DOWN] button for approx. 1 second.
䝿When the black balance adjustment operation starts, the character ABB blinks on the screen.
䝿When the black balance adjustment operation finishes, the character ABB stops blinking and the result
appears for approx. 1 second.
MeaningDisplay
ABB OK Automatic black balance adjustment finished correctly.
ABB NG
CLOSE LENS
Automatic black balance adjustment cannot be performed because the lens iris
is open. Close the lens iris.
ABB NG Automatic black balance adjustment cannot be performed.
Operate the automatic black balance again.
6OPERATION
61 Automatic Black Balance
䐜When switching the FORMAT switch on the back panel of the unit, be sure to perform the ABB adjustment,
refer to the item “6.1 Automatic Black Balance”.

12
ATW
Automatic Tracking
White Balance䟻
䟻䟻
䟻
AWB
䟺
䟺䟺
䟺䟺
䟺䟺
䟺Automatic White Balance䟻
䟻䟻
䟻
MANUAL
䟺
䟺䟺
䟺Manual White Balance䟻
䟻䟻
䟻
Outline
The camera measures the
object color temperature and
adjusts the white balance
automatically.
Adjust white balance by
displaying the white object
inside the area set by AWB
menu and pressing the
[DATA UP] button.
Adjust the white balance
manually using the WHT
BAL menu while shooting
the white object.
Features
Tracks variations of color
temperature and adjusts white
balance automatically.
Measurement accuracy is
higher than ATW. This
mode is effective when
shooting under less varia-
tions of color temperature.
Artificial white balance setting.
The manual adjustment is
most effective under shooting
conditions with no color
temperature variation.
Notes
If illumination is low, white
balance may not be corrected.
Adjustment is performed by
confirming with a vector
scope.
䐖AWB(Automatic White Balance)
䝿Set the MODE to AWB on the WHT BAL menu.
Perform the C.TEMP (color temperature conversion) setting, if necessary.
(Refer to the item “7.2 (3) WHT BAL (White Balance)”.)
3200K䠌Appropriate for indoor shooting.
5600K䠌Appropriate for outdoor shooting.
䝿If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the [DISP]
button to disable the color bar pattern or the character display on the menu.
䝿Shoot a known white object entirely in the area set by the AWB menu (refer to the item “7.2 (3) (3.1) (d)
Confirming the contents of the zone area selected by AWB” ) and push [DATA UP] button for approx. 1 second.
䝿The character AWB blinks on the screen when the AWB starts.
䝿The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.
62 White Balance
For white balance adjustment of this unit, ATW (Automatic Tracking White balance), AWB (Automatic
White Balance) and MANUAL (Manual white balance) adjustments are provided. Refer to the items “7.2
(3) WHT BAL (White Balance), 7. MODE SETTING BY THE ON SCREEN DISPLAY”, select the desired
mode.

13
MeaningDisplay
AWB OK Automatic white balance adjustment finished correctly.
AWB NG
LEVEL LOW
Automatic white balance adjustment cannot be performed because the video level is
too low.
Adjust the video level by increasing the illumination or opening the lens iris.
AWB NG
LEVEL HIGH
Automatic white balance adjustment cannot be performed because the video level is
too high.
Adjust the video level by decreasing the illumination or closing the lens iris.
AWB NG
C. TEMP LOW
Automatic white balance adjustment cannot be performed because the color
temperature is too low.
If the C.TEMP is set to 5600K, set to 3200K.
If the message appears with the C.TEMP set to 3200K, change the illumination or
use a color temperature conversion filter.
AWB NG
C. TEMP HIGH
Automatic white balance adjustment cannot be performed because the color
temperature is too high.
If the C.TEMP is set to 3200K, set to 5600K.
If the message appears with the C.TEMP set to 5600K, change the illumination or
use the color temperature conversion filter.
AWB NG Automatic white balance adjustment cannot be performed for other reasons. Such as
no white area is included in an object, etc.
䐗MANUAL(Manual white balance)
䝿Set the MODE to MANUAL on the WHT BAL menu.
(Refer to the item “7.2 (3) WHT BAL (White Balance)”.)
䝿Shoot a known white object, set the white balance by adjusting the levels of R GAIN and B GAIN on the
menu, confirming with a monitor or a vector scope.
(Refer to the item “7.2 (3) (3.3) Changing gain in MANUAL mode”.)

14
.:*7(*3*+.1*7&6*&:&.1&'1*&797*62*246.*7+468-.793.8-*7*&6*(-47*3)*5*3).3,
437-448.3,(43).8.437=97.3,8-*$%'988438-*(&2*6&45*6&8.43.7(-&3,*).22*).&8*1=+6428-*
(966*381=7*1*(8*)(*3*.1*848-*3*<8*+*6848-*.8*2>#
#?
䝿 "-.1*&3=2*39.7).751&=*)56*77.3,8-*$%'98843;.11).751&=8-*2*397*88.3,7+468-*3*<8(*3*.1*
 䊲
䊲䊲
䊲  䊲
䊲䊲
䊲  䊲
䊲䊲
䊲  䊲
䊲䊲
䊲 
䝿 "-*38-*$%'98843.756*77*);-.1*8-*(&2*6&.7.31.:*.2&,*24)*8-*(966*387(*3*+.1*7*1*(8.43
&88-&88.2*.7).751&=*)+46&5564<7*(43)7.38-*955*66.,-8(463*64+8-*7(6**3+8-*$%'98843.7
56*77*)&,&.3;-.1*8-*547.8.43.7).751&=*)8-*7(*3*+.1*(=(1*7&7)*7(6.'*)&'4:*
"-*38-*.2&,*.7)&60*:*3.+8-*1*37.6.7.745*3(-&3,*8-*,&.3:.)*4,&.384,*88-*)*7.6*):.)*41*:*1
46,&.3&)/9782*384+8-*93.8 9842&8.(,&.3(438641 &39&1)24)*7
&6*564:.)*)*1*(88-*24)*438-*2*39*+*6848-*.8*2>!.)*4,&.3?
䐖  9842&8.(,&.3(438641
 "-*38-*498598.714;,&.3.7&9842&8.(&11=&)/978*)84&79.8&'1*:.)*41*:*1
-*2&<.292:&19*4+,&.3.7)&3)(&3'*7*8+64284).3)78*57*+*6848-*.8*2
>-&3,.3,8-*2&<.292,&.3.3 9842&8.(,&.3(43864124)*? 

!.)*41*:*1!5*&0&:*6&,*:&19*6&8.4!&3)2*&796*2*381.,-8&6*&&6*1.30*)
848-*7*88.3,438-*&9842&8.(7-988*6*+*6848-*.8*2>-&3,.3,8-*7*88.3,.3 24)*?
䐗  &39&1,&.3
 &.3&)/9782*38.75*6+462*)438-*2*39-*&)/9782*386&3,*.7+64284).3)78*57
*+*6848-*.8*2>-&3,.3,,&.3.3 24)*?
䐘 
 &.3.7+.<*)&8)
 䊲
䊲䊲
䊲  䊲
䊲䊲
䊲 
63 Scene File
64 Gain
&.3'98843
ձ+8-*$%'98843.756*77*)8-*(966*38,&.37*88.3,.7).751&=*)+46&5564<7*(43)7
2*39
>㸨㸨?7-4;78-*7*88.3,,&.3.3 24)*
ղ+8-*$%'98843.756*77*)&,&.3;-.1*8-*(966*387*88.3,24)*.7).751&=*)8-*,&.324)*(&3'*
(-&3,*)
4+@.3 24)*&3) 24)*(&3348'*(-&3,*)
A
 A 
 㸨㸨)A)

15
Due to the lens used or the environmental condition, color shading may occur at the upper and lower edge
of the screen. If this happens, the shading correction function can be used to decrease the amount of color
shading. For shading correction of the unit, SET (Automatic shading correction), MANUAL (Manual shading
correction), and OFF (no shading correction) modes are provided. Select the mode on the OPTION menu.
(Refer to the item “7.2 (7) (7.2) Changing shading correction mode”.)
䐖SET(Auto shading)
䡗If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the
[DISP] button to remove them from the screen.
䝿Push the [MENU UP] button for approx. 1 second.
䝿When the automatic shading correction operation starts, the character SHD blinks on the screen.
䝿When the automatic shading correction operation terminates, the character SHD ends blinking and the
result is displayed for approx. 1 second.
MeaningDisplay
SHD OK Automatic shading correction operation finished correctly.
SHD OK
LIMIT
Automatic shading correction operation finished, however, the correction
necessary exceeds the camera’s range so the maximum possible value is applied.
SHD NG
LEVEL LOW
Automatic shading correction cannot be performed because the video level is too
low. Adjust the video level by increasing the illumination or opening the lens iris.
SHD NG
LEVEL HIGH
Automatic shading correction cannot be performed because the video level is too
high. Adjust the video level by decreasing the illumination or closing the lens iris.
䐗MANUAL(Manual Shading)
Perform the correction amount setting on the OPTION menu, confirming with a monitor or a vector scope.
(Refer to the “7.2 (7) (7.3) Changing manual shading correction mode”.)
䐘OFF
The status is no shading correction.
* Shading correction is only effective when the lens iris and zoom ratio is fixed. Use the unit with
SHADING OFF for variable lens conditions.
Note:
Before shading correction is performed, please shoot a known white object that fills the screen in
the proper video level and set the automatic white balance (AWB) .
.
65 Shading Correction
Note:
White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just
certain characteristics of the CCD becoming more visible.

16
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The
contents once set are memorized in the scene files (A, B, C, D, E) selected, so if the power turns off, it is
unnecessary to set again when using the unit next time. When the setting is performed, select the menu of
the item to be set.
When the power turns on, the normal screen showing only the video signal appears. Change the output to
each screen (video signal output, color bar screen, Index menu, menus, and area menu) by using the [DISP],
[PAGE], [MENU UP], and [MENU DOWN] buttons.
* A menu is selected when pushing the [PAGE] button after moving the “䊲” on the screen by the [MENU
UP], [MENU DOWN] button while the Index menu is displayed.
7MODE SETTING BY THE ON SCREEN DISPLAY
71 Using the Menus
USER
USER
Area menu
DATA
UP/DOWN
DATA
UP/DOWN
The screen is changed to the area screen by
selecting AUTO in the 1.SHUTTER menu and
AWB in the 3.WHT BAL menu in the setting
screen For more details, refer to the item "7.2
Menus".
D
A
B
C
E
DISP DISP
D
A
B
C
E
Area menu
POWER SW
ON
Video signal output
DISP
PAGE
PAGE
1.SHUTTER 2.GAIN 3.WHT BAL 4.PROCESS 5.MATRIX 6.SYNC
Color bar screen
Menus
Index menu
DISP DISP
PAGE PAGE PAGE PAGE
PAGE PAGE
AUTO
MANU
NOAWB
OFF
OFF
INT
EXT.ATW
MANU
GAMMA
ON
GAMMA
OFF
AUTO
MANU
SS
PAGE
DISP
7.OPTION
PAGE
RGB
Y/Pb/Pr

17
䝿Select the menu to change the setting by referring to the item “7.1 Using the Menus”.
䝿When the [MENU UP], [MENU DOWN] buttons are pushed, the “䊲” on the screen moves up and down.
Move the “䊲” to the item whose setting you wish to change.
1 SHUTTER䟺Electronic shutter䟻
The electronic shutter has four modes; AUTO, MANUAL, SS(Synchro. Scan).
Press the “Page” button to enter the Shutter Page. Use the “Data Up/Down” buttons to select the Shutter
Mode.
AUTO MANUAL SS
AUTO 䠌The exposure time is controlled automatically to obtain the video level set.
MANUAL 䠌It is possible to select the exposure time from eleven speed settings; OFF (1/60s), 1/100s,
1/125s, 1/250s, 1/500s, 1/1000s, 1/3000s, 1/5000s, 1/10000s, 1/30000s, 1/50000s.
Note:
When setting a rapid shutter speed, sensitivity degrades according to the speed.
When a discharging light such as fluorescent lamp, etc. is used for the illumination,
the flicker may be large.
SS 䠌Shutter speed can be set by the horizontal scanning time (1H) unit.
72 Menus

18
䟺
䟺䟺
䟺1䠀
䠀䠀
䠀1䟻
䟻䟻
䟻Changing the setting in AUTO mode
Shutter mode AUTO, MANUAL, SS
Video level adjustment -100 to 100
Peak and average ratio adjustment 00 10 to 10 00
-- 1 SHUTTER -- <FILE A>
Automatic shutter response speed adjustment 1 to 20
MODE AUTO
LEVEL 0
Automatic shutter area selection
PEAK AVE 05 05
PRESET A, PRESET B, PRESET C, PRESET D, PRESET E,
USER
SPEED 10
AREA PRESET A
AREA DISPLAY OFF
< MODE = AUTO>
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
Automatic shutter area display selection
(a) Changing the video level in the automatic shutter mode
䐖Move the “䊲” to LEVEL by pushing [MENU UP], [MENU DOWN] buttons.
䐗Select the video level by pushing [DATA UP], [DATA DOWN] buttons.
[DATA UP]㻃㻃㻃㻃㻃㻃㻃㻃The value increases by pushing
-100 0 100
The value decreases by pushing 㻃㻃㻃㻃 [DATA DOWN]
(b) Changing the automatic shutter detection (ratio between peak and average value)
䐖Move the “䊲” to PEAK/AVE by pushing [MENU UP], [MENU DOWN] buttons.
䐗Select the ratio between peak and average value by pushing [DATA UP], [DATA DOWN] buttons.
(Peak䠌Average) The peak value increases by pushing [DATA UP]
00䠌10 05䠌05 10䠌00
The peak value decreases by pushing 㻃㻃㻃㻃㻃㻃[DATA DOWN]
(c) Changing the automatic shutter response speed
䐖Move the “䊲” to SPEED by pushing [MENU UP], [MENU DOWN] buttons.
䐗Select the response speed by pushing [DATA UP], [DATA DOWN] buttons.
[DATA UP] 㻃㻃㻃㻃㻃㻃㻃The response speed becomes faster by pushing
1 10 20
The response speed becomes slower by pushing [DATA DOWN]

19
(d) Changing the automatic shutter zone area
The available picture area is shown by the shading correction on the screen that is parted in 64.
䐖Move the “䊲” to AREA by pushing [MENU UP], [MENU DOWN] buttons.
䐗Select the measurement light area by pushing [DATA UP], [DATA DOWN] buttons.
(e) Confirming the contents of the measurement light area selected by the automatic shutter
䐖Set the “䊲” to AREA DISP by pushing [MENU UP], [MENU DOWN] buttons.
䐗Area screen appears by pushing [DATA UP], [DATA DOWN] buttons.
When AREA is set to USER, the setting can be changed on the area menu. When changing the area,
refer to the item “7.2 (8) Setting USER area”.
䐘Push the [DISP] button to return to the menu.
䠭DATA UP䠯
PRESET A PRESET B PRESET C PRESET D PRESET E USER
䠭DATA DOWN䠯
PRESET A PRESET B PRESET DPRESET C
PRESET E USER
Custom
Selection

20
䟺
䟺䟺
䟺1䠀
䠀䠀
䠀2䟻
䟻䟻
䟻Changing the setting in MANUAL mode
Shutter mode AUTO, MANUAL, SS
-- 1 SHUTTER -- <FILE A>
Shutter speed setting
MODE MANUAL OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,
MANUAL 1 10000s 1/3000s, 1/5000s, 1/10000s, 1/30000s, 1/50000s
< MODE = MANUAL>
(a) Changing the shutter speed
䐖Move the “䊲” to MANU by pushing [MENU UP], [MENU DOWN] buttons.
䐗Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
䠭DATA UP䠯
OFF 1/100s 1/125s 1/250s 1/500s 1/1000s 1/3000s 1/5000s 1/10000s 1/30000s 1/50000s
䠭DATA DOWN䠯
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN
䟺
䟺䟺
䟺1䠀
䠀䠀
䠀3䟻
䟻䟻
䟻Changing the setting in SS (Synchro. Scan) mode
Shutter mode AUTO, MANUAL, SS
-- 1 SHUTTER -- <FILE A>
Synchro. scan setting
MODE SS 1 1125H 560 1125H OFF
SYNCHRO SCAN OFF
< MODE = SS >
(a) Changing the shutter speed setting
䐖Move the “䊲” to SYNCHRO SCAN by pushing [MENU UP], [MENU DOWN] buttons.
䐗Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
䠭DATA UP䠯
1/1125H 560/1125H OFF
䠭DATA DOWN䠯
Move up and down
by pushing
MENU UP,DOWN
Select the desired
value by pushing
DATA UP,DOWN