Chicago Electric 65298 Installation manual

RECIPROCATING SAW
65298
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10c

SKU 65298 For technical questions, please call 1-800-444-3353. Page 2
CONTENTS
IMPORTANT SAFETY
INFORMATION............................3
GENERAL POWER TOOL
SAFETY WARNINGS.......................3
RECIPROCATING SAW SAFETY
WARNINGS......................................5
GROUNDING.................................7
DOUBLE INSULATED TOOLS:
TOOLS WITH TWO PRONG
PLUGS.............................................7
EXTENSION CORDS .........................8
SYMBOLOGY.....................................8
SPECIFICATIONS..........................9
UNPACKING..................................9
SAW BLADE INSTALLATION.......9
OPERATING INSTRUCTIONS ......9
FEATURES.........................................9
WORK PIECE AND WORK AREA
SET UP ..........................................10
HANDLE ROTATION........................10
TRIGGER FEATURES......................10
GENERAL CUTTING........................10
PLUNGE CUTTING..........................11
METAL CUTTING.............................11
MAINTENANCE AND
SERVICING ...............................12
INSPECTION, MAINTENANCE,
AND CLEANING............................12
TROUBLESHOOTING......................13
PARTS LIST.................................14
ASSEMBLY DIAGRAM................15
LIMITED 90 DAY WARRANTY....16

SKU 65298 For technical questions, please call 1-800-444-3353. Page 3
SAVE THIS MANUAL
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information provid-
ed with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Power Tool Safety
Warnings
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future reference.
The term ″power tool″ in the
warnings refers to your mains-
operated (corded) power tool or
battery-operated (cordless) power
tool.
Work area safety1. Keep work area clean and well lit.a.
Cluttered or dark areas invite acci-
dents.
Do not operate power tools inb.
explosive atmospheres, such as in
the presence of ammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust or
fumes.
Keep children and bystandersc.away while operating a power tool.
Distractions can cause you to lose
control.
Electrical safety2. Power tool plugs must match thea.
outlet. Never modify the plug in
any way. Do not use any adapter

SKU 65298 For technical questions, please call 1-800-444-3353. Page 4
plugs with grounded power tools.
Unmodied plugs and matching out-
lets will reduce risk of electric shock.
Avoid body contact with groundedb.
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
Do not expose power tools to rainc.or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never used.
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk
of electric shock.
When operating a power tool out-e.
doors, use an extension cord suit-
able for outdoor use. Use of a cord
suitable for outdoor use reduces the
risk of electric shock.
If operating a power tool in a dampf. location is unavoidable, use a
Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of
a GFCI reduces the risk of electric
shock.
Personal safety3. Stay alert, watch what you are do-a.
ing and use common sense when
operating a power tool. Do not use
a power tool while you are tired
or under the inuence of drugs,
alcohol or medication. A moment
of inattention while operating power
tools may result in serious personal
injury.
Use personal protective equip-b.
ment. Always wear eye protection.
Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or
hearing protection used for appropri-
ate conditions will reduce personal
injuries.
Prevent unintentional starting.c.Ensure the switch is in the off-po-
sition before connecting to power
source and/or battery pack, pick-
ing up or carrying the tool. Carry-
ing power tools with your nger on
the switch or energizing power tools
that have the switch on invites acci-
dents.
Remove any adjusting key or
d.
wrench before turning the power
tool on. A wrench or a key left at-
tached to a rotating part of the power
tool may result in personal injury.
Do not overreach. Keep propere.
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear loosef. clothing or jewelry. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewelry or long hair can be caught in
moving parts.
If devices are provided for the con-g.
nection of dust extraction and col-
lection facilities, ensure these are
connected and properly used. Use
of these devices can reduce dust-
related hazards.
Only use safety equipment thath.
has been approved by an appropri-
ate standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breath-
ing protection must be NIOSH-ap-

SKU 65298 For technical questions, please call 1-800-444-3353. Page 5
proved for the specic hazards in the
work area.
Power tool use and care4. Do not force the power tool. Usea.
the correct power tool for your ap-
plication. The correct power tool will
do the job better and safer at the rate
for which it was designed.
Do not use the power tool if theb.
switch does not turn it on and off.
Any power tool that cannot be con-
trolled with the switch is dangerous
and must be repaired.
Disconnect the plug from thec.power source and/or the battery
pack from the power tool before
making any adjustments, chang-
ing accessories, or storing power
tools. Such preventive safety mea-
sures reduce the risk of starting the
power tool accidentally.
Store idle power tools out of thed.
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to oper-
ate the power tool. Power tools are
dangerous in the hands of untrained
users.
Maintain power tools. Check fore.
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If dam-
aged, have the power tool repaired
before use. Many accidents are
caused by poorly maintained power
tools.
Keep cutting tools sharp andf. clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier to
control.
Use the power tool, accessoriesg.
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed. Use
of the power tool for operations differ-
ent from those intended could result
in a hazardous situation.
Service
5. Have your power tool serviced bya.
a qualied repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
Reciprocating Saw Safety
Warnings
Hold power tool by insulated grip-1. ping surfaces when performing an
operation where cutting tool may
contact hidden wiring or its own
cord. Contact with a ″live″ wire will
make exposed metal parts of the tool
″live″ and shock the operator.
Use clamps or another practical2. way to secure and support the
work piece to a stable platform.
Holding the work by hand or against
your body leaves it unstable and may
lead to loss of control.
Do not cut material that is thicker3. than the Saw Blade is long.
Maintain labels and nameplates on4. the tool. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
Avoid unintentional starting. Prepare5. to begin work before turning on the
tool.

SKU 65298 For technical questions, please call 1-800-444-3353. Page 6
Do not lay the tool down until it has6. come to a complete stop. Moving
parts can grab the surface and pull
the tool out of your control.
When using a handheld power tool,
7.

both hands to resist starting torque.
Do not leave the tool unattended8. when it is plugged into an electrical
outlet. Turn off the tool, and unplug it
from its electrical outlet before leav-
ing.
This product is not a toy. Keep it out9. of reach of children.
People with pacemakers should10. consult their physician(s) before use.
-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure. In addition, people with
pacemakers should:



avoid electrical shock.

grounded. Ground Fault Circuit Inter-
rupter (GFCI) should also be imple-
mented – it prevents sustained elec-
trical shock.
Some dust created by power sand-11. ing, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of Cali-
fornia] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:

-
ment or other masonry products
-
cally treated lumber
Your risk from these exposures var-
ies, depending on how often you do
this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially

particles. (California Health & Safety
Code § 25249.5, et seq.)
WARNING: Handling the cord on12. this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
The warnings, precautions, and in-
13. structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
Vibration Safety
This tool vibrates during use. Re-
peated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
Anyone using vibrating tools regu-1. larly or for an extended period should

then have regular medical check-
ups to ensure medical problems are
not being caused or worsened from

SKU 65298 For technical questions, please call 1-800-444-3353. Page 7
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries, ner-
vous system disorders, diabetes, or
Raynaud’s Disease should not use
this tool. If you feel any medical or
physical symptoms related to vibra-
tion (such as tingling, numbness, and

advice as soon as possible.
Do not smoke during use. Nico-2. tine reduces the blood supply to the

of vibration-related injury.
Wear suitable gloves to reduce the
3. vibration effects on the user.
Use tools with the lowest vibration4. when there is a choice between dif-
ferent processes.
Include vibration-free periods each5. day of work.
Grip tool as lightly as possible (while6.

the tool do the work.
To reduce vibration, maintain the tool7. as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
SAVE THESE
INSTRUCTIONS.
GROUNDING
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM
INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualied
electrician if you are in doubt
as to whether the outlet is
properly grounded. Do not
modify the power cord plug
provided with the tool. Never
remove the grounding prong
from the plug. Do not use the
tool if the power cord or plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the plug will not
t the outlet, have a proper
outlet installed by a qualied
electrician.
Double Insulated Tools: Tools
with Two Prong Plugs
Tools marked “Double Insulated” do1. not require grounding. They have
a special double insulation system

and complies with the applicable
-
tories, Inc., the Canadian Standard
Association, and the National Electri-

SKU 65298 For technical questions, please call 1-800-444-3353. Page 8
cal Code. (See Outlets for 2-Prong
Plug.)
Double insulated tools may be used2. in either of the 120 volt outlets shown
in the preceding illustration. (See
Outlets for 2-Prong Plug.)
Extension Cords
Grounded1. tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
As the distance from the supply outlet2. increases, you must use a heavier
gauge extension cord. Using exten-
sion cords with inadequately sized
wire causes a serious drop in voltage,
resulting in loss of power and pos-
sible tool damage.
(See Table A.)
The smaller the gauge number of the3. wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See Table A.)
When using more than one exten-4. sion cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See Table A.)
If you are using one extension cord5. for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See Table A.)
If you are using an extension cord6. outdoors, make sure it is marked with

indicate it is acceptable for outdoor
use.
Make sure the extension cord is prop-
7. erly wired and in good electrical con-
dition. Always replace a damaged
extension cord or have it repaired by

Protect the extension cords from
8. sharp objects, excessive heat, and
damp or wet areas.
RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS*
(120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25’ 50’ 75’
100’ 150’
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
TABLE A * Based on limiting the line
voltage drop to ve volts at
150% of the rated amperes.
Symbology
Double Insulated
Canadian Standards Association

V~ Volts Alternating Current
AAmperes
n0xxxx/min. 
(RPM)

SKU 65298 For technical questions, please call 1-800-444-3353. Page 9
SPECIFICATIONS
Electrical
Requirements 120 V~ / 60 Hz / 7.5 A
Power Plug 2-Prong, Polarized
Speed 0 to 2,400 SPM
E194601
UNPACKING
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
ASSEMBLY
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Make sure the Trigger of the
Saw is in its “OFF” position
and unplug the tool from its
electrical outlet before
assembling or making any
adjustments to the tool.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
Blade Installation
1. position and the Saw is unplugged
from its electrical outlet.
2. counterclockwise.
Insert blade into Blade Chuck. Be3. sure blade is fully inserted and seat-
ed.
Tighten Blade Chuck by turning it4. clockwise.
Adjusting the
Pivoting Guide Shoe
The Pivoting Guide Shoe serves as a1. rest during the cut, and can be ad-
justed in or out.
To adjust the Guide Shoe, loosen2. the two set screws at the base of
the Guide Shoe, using the 3mm hex
key included with the saw. Pull out or
push in the Guide Shoe as desired,
then retighten the set screws.
Do not attempt to use the saw if3. both screws are not tightened on the
Guide Shoe.

SKU 65298 For technical questions, please call 1-800-444-3353. Page 10
Work Piece and Work Area Set Up
Designate a work area that is clean1. and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
Route the Power Cord along a safe2. route to reach the work area without
creating a tripping hazard or exposing
the Power Cord to possible damage.
The Power Cord must reach the work
area with enough extra length to al-
low free movement while working.
Secure loose workpieces using a vise3. or clamps (not included) to prevent
movement while working.
There must not be hazardous ob-4. jects, such as utility lines or foreign
objects, nearby that will present a
hazard while working.
Check to make sure there is enough5. space under and behind the work-
piece for the Saw Blade. Ensure you
will not be cutting through any electri-
cal wires, pipes, or your workbench.
Trigger Features
The Saw features a1. variable speed
Trigger. For increased strokes per
minute, squeeze the Trigger harder.
For decreased strokes per minute,
apply less pressure to the Trigger.
NOTE: When cutting softer materials, use
a faster speed. When cutting harder
materials, use a slower speed.
The maximum speed of the tool can
2. be adjusted by rotating the dial locat-
ed in the Trigger. Turn the dial toward
the + sign to increase the maximum
speed of the saw.
The Saw also features a continuous
3.

the tool for extended periods of time
squeeze and hold the Trigger, then

unlock the Trigger lock mechanism,
SAW BLADE PIVOTING SHOE
TRIGGER
TRIGGER SPEED CONTROL
TRIGGER
LOCK BUTTON
CHUCK
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Features

SKU 65298 For technical questions, please call 1-800-444-3353. Page 11
squeeze and release the Trigger
once.
General Cutting
Before plugging the Saw into its 1201. volt, grounded, electrical outlet check
to make sure the Trigger is not locked
-
lease the Trigger once to make sure

Make any necessary adjustments to2. the tool as previously discussed, then
plug the Power Cord into the nearest
120 volt, grounded, electrical outlet.

3. then squeeze the Trigger to start the
Saw.
IMPORTANT: Do not start the Saw if the
Saw Blade is in contact with anything
before operation. If necessary, lift
the tool from the workpiece before
squeezing the Trigger.
4. speed set the Pivoting Shoe of the
tool on the workpiece.
With the Saw running, place the Saw5. Blade against the material to be cut.
Do not force the Saw Blade into the
workpiece. Use only enough pres-
sure to keep the Saw cutting. Allow
the Saw Blade to do the work.
If operating the Saw for an extended
6. period, you may wish to lock the
Trigger in its continuous run mode as
previously discussed.
-7. sure on the Trigger to stop the tool. If

used, squeeze and release the Trig-
ger once to stop the Saw. Then un-
plug the Saw from its electrical outlet.
Plunge Cutting
Mark the line of cut.1.
PIVOTING SHOE
SAW BLADE
2. From a convenient starting point
within the cut out area, place the tip
of the Saw Blade over that point with
the Saw parallel to the line of cut.
Slowly lower the Saw until the lower3. edge of the Pivoting Shoe rests on
the workpiece.
Start the Saw and allow it to reach full4. speed.
With the Saw resting on the Pivoting5. Shoe, slowly lower the Saw Blade
onto the cut line. Continue this mo-
tion until the Saw Blade is perpen-
dicular to the workpiece.
Metal Cutting
When cutting metal materials with the1. Saw, make sure to use a metal Saw
Blade designed for this purpose.
-2. ting oil to avoid heat build-up. Follow
the “General Cutting” section in this
manual.

SKU 65298 For technical questions, please call 1-800-444-3353. Page 12
MAINTENANCE AND
SERVICING
Procedures not specically
explained in this manual
must be performed only by a
qualied technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Make sure the Trigger of the
Saw is in its “OFF” position
and unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
Inspection, Maintenance, and
Cleaning
1. general condition of the Saw. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
CARBON BRUSH MAINTENANCE.2.
The carbon brushes may require
maintenance when the motor perfor-
mance of the tool decreases or stops
working completely. To maintain the
brushes:
Remove the brush cap on the topa. and bottom of the motor housing.
Remove the carbon brushes from
b. the housing. Keep track of which
orientation the old carbon brush-
es were in to prevent needless
wear if they will be reinstalled.
If either carbon brush is worn downc. by more than 1/2, replace both car-
bon brushes.
To clean old carbon brushes befored. reusing them, rub the contact areas
with a pencil eraser.
Reinsert the old carbon brushes in
e. the same orientation to reduce wear.
When installing the carbon brushes,f. make sure the carbon portions of the
carbon brushes contact the motor
armature, and that the springs face
away from the motor. Also, make
sure the springs operate freely.
Replace the brush caps. Do notg. overtighten.
Note: New carbon brushes tend to spark

conform to the motor’s armature.
AFTER USE,3. clean all external sur-
faces of the tool with clean cloth.
4. WARNING! If the Power Cord of
this tool is damaged, it must be re-
placed only by a qualied service
technician.

SKU 65298 For technical questions, please call 1-800-444-3353. Page 13
Troubleshooting
Problem Possible Causes Possible Solutions
Tool will not start. No power at outlet.1. Power Cord not connected.2. Check power at outlet.1. Check that Power Cord is plugged in.2.
Irregular cut line. Bent, cracked, broken, or1. loose Saw Blade.
Improperly exerting side-to-2. side pressure on Saw Blade.
Replace Saw Blade. Make sure Blade is1. securely installed in tool.
Hold blade at a 90° angle from workpiece.2.
Undesirable cutting
action. Dull Saw Blade.1. Improper Saw Blade used.2.
Tool speed too slow.3.
Attempting to cut curves with4. tool.
Replace Saw Blade.
1. Use metal Saw Blades for cutting metal and2. wood Saw Blades for cutting wood.
Increase tool Speed by squeezing Trigger3. harder.
Use tool only to cut straight lines.4.
Follow all safety precautions whenever diagnosing or servicing the
tool. Disconnect power supply before service.
PLEASE READ THE FOLLOWING CAREFULLY













SKU 65298 For technical questions, please call 1-800-444-3353. Page 14
PARTS LIST
Part Description
a1 Blade (Wood Cutting)
b1 Blade (Metal Cutting)
2 
3 Set Screw
4 Retaining Sleeve
5 Positioning Screw
6 Blade Holder
7 Spring
8 Blade Head Base
9 Blade Head Pin
10 Reciprocating Shaft
11 Screw
12 Carbon Brush Assembly
13 Right Housing
14 Pivoting Shoe
15 Screw
16 Press Board
17 Sleeve
18 Seal
19 Nut
20 Spring Washer
21 Washer
22 Internal Hex Bolt
23 Front Gearbox
24 Bearing 6002
25 Screw
26 Spring Washer
27 Washer
28 
PARTS LIST
Part Description
29 Bearing Sleeve
30 Axle Spring Retaining Ring
31 Spring Retaining Ring
32 Bearing 6002
33 Bearing 6002
34 Cam
35 Spring Retaining Ring
36 Cam Shaft
37 Transmission Shaft
38 Pin
39 Pin
40 Gear
41 Pin
42 Bolt
43 Washer
44 Roller Bearing
45 
46 Rear Gearbox
47 Seal
48 Bearing 629
49 Fan
50 Rotor
51 Carbon Brush Assembly
52 
53 Bearing 627
54 Stator
55 Power Cord
56 Trigger
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.

SKU 65298 For technical questions, please call 1-800-444-3353. Page 15
ASSEMBLY DIAGRAM

SKU 65298 For technical questions, please call 1-800-444-3353. Page 16
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you.-


To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.

which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]