Chicago Faucets EQ Series Instruction Manual

EQ Series User Guide Installation Instructions
For single supply and dual supply EQ Series faucets
1For additional technical assistance, call 800/TEC-TRUE (800-832-8783) or visit our website at chicagofaucets.com.
Mounting of Faucet and Optional Cover Plate
Connect Water Supply (dual supply unit shown)
1. Install gasket flat side
down. If installing a
cover plate, align holes
in spout base with pins
on plate. Feed the power
cable and braided hose
through plate. Secure
plate to spout.
1. Remove the control box
cover by using a #2 Phillips
screwdriver to loosen the
cover screw.
1. Check to see that the
screen filters are
present.
2. Attach the threaded
rods to bottom of the
cover plate. Apply
sealant to underside of
the cover plate where
shown.
2. Pivot yellow locking tab
and remove metal key
at top of box. Apply
silicone-based lubri-
cant to the end of the
spout hose and insert it
through the hole.
2. Attach3/8˝compression
supply hoses from con-
trol box to the supply
stops. Wrench tighten.
1. Determine position of the control box, hold it against
the wall and mark the locations of the two mounting
holes.
FOR EQ CONNECT UNITS
Confirm mounting position allows attachment of power
wires from faucet to connectors at bottom of box.
3. Open supply stops and
check for leaks. Water
may run through spout.
3. Position faucet on sink. Hand-
tighten spout to deck with the large
black spacer and long mounting
nut. For cover plate installation,
attach the large cup washers, flat
washers, and wing nuts to the
threaded rods.
Tighten mounting nut with flat
head screwdriver or wrench.
In order to complete the installation, you will need the following tools and supplies:
• Phillips Screwdriver, #1, #2, #3 • Drill,with3/16˝Bit
• Adjustable Wrench • Mallet
Insert Wires From Spout Into Control Box
1. Bringwireintobox.Snapwireintoholderonsideofbox.
FOR EQ CONNECT UNITS
Attach wires to bottom of control box cover, gray to gray and black to black.
Snap wire into holder on side of box.
1
1
1
2
2
2Flat head
Mount Control Box
Remove screw
for box access
24˝
(61 cm)
1
2
1
2
3
Overview
Chicago Faucets EQ Series faucets feature two designs in two finishes with heavy-duty cast brass spouts and high-quality electronic components. The faucet is up and running in minutes
without the need for programming. Superior user detection means EQ turns on when user approaches and shuts off when user leaves. It also adjusts for optimal performance, saving water.
Safety Information
Read this entire user guide to ensure proper installation. Compliance and conformity to local codes and ordinances is the
responsibility of the installer. The following safety notes must always be complied with during handling of this product:
• Make sure there is enough space and lighting available during installation and service.
• Do not modify or convert this Chicago Faucets product yourself. All warranties will be voided.
Notice to the Installer
• Read this entire instruction sheet before installing to ensure proper installation.
• Installation must comply with local codes and ordinances.
• Do not use pipe dope.
• Care shall be exercised when installing the device to prevent marring the exposed, decorative surfaces.
The supply piping to these devices shall be securely anchored to the building structure to prevent installed device from unnecessary movement when operated by the user.
NOTE: The information in this manual is subject to change without notice.
Installation may be performed at different times of construction by different individuals.
For this reason, these instructions should be left on-site with the facility or maintenance manager.
NOTE:Beforeinstallation,turnoffwatersuppliestoexistingfaucetandremovefaucetifreplacing.Cleanfaucetbasinandclearawaydebris. Flush all supply lines before connecting to faucet.
Failure to do so can result in debris clogging the inlets and/or internal control and mixing valves.
• Tape Measure • Sealant
• Silicone-based Lubricant •1/2˝DeepSocketor#3FlatHeadScrewdriver
Attach Braided Hose to Control Box
17-21˝
(43-53 cm)
#2 Phillips
H C
IMPORTANT: Remove any debris or hardware from the
sink before opening the supplies and testing the faucet.
Operating static pressure: 20-125 PSI (138-862 kPa)
Minimum static pressure for mixing: 30 PSI (207 kPa)
COLD water inlet temperature range: 40-80°F (4-27°C)
HOT water inlet temperature range: 100-180°F (38-82°C)
Maximum hot water range outlet from thermostatic
mixing valve: 80-120°F (27-49°C)
Maximum hot water range outlet from mechanical mixing
valve: 40-140°F (4-60°C)
Maximum pressure differential between Hot & Cold water
supplies: 20%;
Minimum inlet water supply temperature differential:
20°F (9°C)
Connect Power: Plug-in or Hardwire (AC)
1. Choose a location and mount
the transformer. Run the
cable from the transformer
through opening in control
box.
2. Attach wiring connectors
(gray to gray, black to
black). Snap the completed
connections into the wiring
harness as shown.
OR
3. Plug the
transformer into
the wall.
4. Wire up the
transformer to the
main line.
3.Besuretoseathose
firmly before reinstalling
metal key and securing it
with yellow locking tab.
1
2. Drill3/16˝holes,install
anchors and mounting
screws.Besuretoleave
atleast1/2˝(12mm)
of the screw head
exposed. Secure the
control box to wall.
1
2
#1 Phillips
1
2
Connect Power: Battery (DC)
1. Open yellow battery
housing and insert
batteries according to
diagram inside housing.
2. Attach wiring connectors (gray to gray, black to black). Snap the
completed connections into wiring harness.
FOR EQ CONNECT UNITS
The wiring connectors are located on the inside of the control box cover.
1. Use 2-sided tape to secure
transformer to the top of
the control box or on the
wall. Run the cable from the
transformer through opening
in control box.
2. Attach wiring connectors
located on the inside of the
control box cover (gray to
gray, black to black). Snap
the completed connections
into the wiring harness.
FOR EQ CONNECT UNITS
Faucets equipped with EQ Connect allow additional adjustments to meet specific
needs with a smart phone or tablet using the EQ Connect app for Android or iOS.

EQ Series User Guide Installation Instructions
(continued)
2
Care and Maintenance
Periodic inspection and yearly maintenance by a licensed contractor is required for all thermostatic mixing elements. Corrosive water conditions and/or unauthorized adjustments or repair could
render the thermostatic valve ineffective for service intended. Regular checking and cleaning of the valve’s internal components and check stops helps assure maximum life and proper product
function.Frequencyofcleaningandinspectiondependsonlocalwaterconditions.AllChicagoFaucetsttingsaredesignedandengineeredtomeetorexceedindustryperformancestandards.
Care should be taken when cleaning this product. Do not use abrasive cleaners, chemicals, or solvents as they can result in surface damage. Use mild soap with warm water for cleaning and
protectingthesurfaceofChicagoFaucetsttings.
For additional technical assistance, call 800/TEC-TRUE (800-832-8783) or visit our website at chicagofaucets.com.
CHICAGO FAUCETS LIMITED WARRANTY
TO WHOM DOES THIS WARRANTY APPLY? — The Company extends the following limited warranty to the original user only.
WHAT DOES THIS WARRANTY COVER AND HOW LONG DOES IT LAST?
This warranty covers the following Commercial Products:
LIFETIME FAUCET WARRANTY—The“Faucet,”denedasanymetalcast,forged,stampedorformedportionoftheProduct,notincludingelectronicormovingpartsorother
products separately covered by this Limited Warranty or water restricting components or other components, is warranted against material manufacturing defects for the life of the Product.
FIVE YEAR FAUCET WARRANTY—CertainProductsandportionsoftheProductarewarrantedagainstmaterialmanufacturingdefectsforaperiodofve(5)yearsfromthedateofProductpurchase.Productswarrantedagainstmaterial
manufacturingdefectsforaperiodofve(5)yearsfromthedateofProductpurchasearereferredtobytheproductnumbers42X,43X,15XXandE-Tronic®-4X,5X,6X,7X,8Xand9X.AllzincdiecastportionsofProductarewarrantedagainst
materialmanufacturingdefectsforaperiodofve(5)yearsfromthedateofProductpurchase.
THREE YEAR ELECTRONICS WARRANTY — Electronic components, including the solenoid, are warranted for three (3) years from the date of installation.
FIVE YEAR CARTRIDGE WARRANTY—The“Cartridge”,denedasthemetalportionofanyProducttypicallyreferredtobytheproductnumberscontaining1-099,1-100,377X,
217Xand274X,excludinganyrubberorplasticcomponents,iswarrantedagainstmaterialmanufacturingdefectsforaperiodofve(5)yearsfromthedateofProductpurchase.
AllCartridgesincludedintheCompany’sSingleControlorShowerProductsalsoarewarrantedagainstmaterialmanufacturingdefectsforaperiodofve(5)yearsfromthedateofProductpurchase.
ONE YEAR FINISH WARRANTY – COMMERCIAL—ForProductsusedincommercialapplications,thenishoftheProductiswarrantedagainstmaterialmanufacturingdefectsforaperiod
of one (1) year from the date of Product purchase.
OTHER WARRANTIES — All other Products not covered above are warranted against material manufacturing defects for a period of one (1) year from the date of Product purchase.
Other restrictions and limitations apply. For complete warranty details, call Chicago Faucets Customer Service at 847-803-5000 or visit chicagofaucets.com.
© 2020 Chicago Faucet Company 957.109.00.0 06/20
The Chicago Faucet Company
2100 South Clearwater Drive
Des Plaines, IL 60018
Phone: [phone]
Fax: [phone]
Technical: 800/832-8783
www.chicagofaucets.com
User Adjustable Temperature Control
WARNING!
Delivery of water to fixtures intended for hand washing is recommended to be controlled by valves listed to ASSE 1070. This fitting is NOT factory preset and can be adjusted to deliver water at temperatures exceeding 110°F (43°C).
Further, mechanical mixing valves DO NOT provide automatic control of water temperature. Due to effects of various water conditions, periodic verification of outlet water temperature is required.
3. Reinstall the control box
cover and secure it with
the #2 Phillips screw.
1. Thread “T” connector
into yellow handle.
Slide the connecting
rod through slot in
handle and pull up
until it catches.
NOTE:Besurenottokinkcable.Limitcableloopingwherepossible.
2. Slide black riveted
attachment into the
groove of the control
box and push back
into large opening.
Completing Installation: Testing and Adjustment
1. Once wiring is
complete, the red
sensor light at the
outlet will glow for 5
seconds. After the light
switches off, place
your hands in front of
the faucet to activate.
2. Adjusting the Water Temperature
a. The yellow handle in the control box is used to adjust
water temperature. Turn clockwise to decrease or
counter-clockwise to increase temperature.
b. Water temperature must be checked at the point of
use. Temperature should not exceed 110°F (43°C).
Temperatures in excess 110°F (43°C) are dangerous
and may cause scalding, severe injury or death!
3. Slide locking clip into
place.
Remove screw
for box access
LTPS End of Life Directives (Recycling) In an effort to produce environmentally conscious products, the LTPS
contains materials that are required to be recycled by specialized companies. Please ensure you dispose of your
LTPS according to local regulations. Follow applicable laws and regulations for transport, shipping, and disposal of
batteries. For details on, and locations for recycling lithium based batteries, please contact a government recycling
agency, your waste-disposal service, or visit reputable on-line recycling sources such as www.call2recycle.org.
The faucet is leaking:
Fromoutlet–tightenorreplaceoutletinsertusingincludedkey.Fromsupplystops–installorreplacelterscreengaskets.
No water ow or ow is limited:
Makesuresupplyhosesareconnectedandstopsarefullyopen.Cleanorreplacelterscreengasketsoroutletinsert.Checkall
electronic connections.
Water ow does not stop:
Ifwaterowscontinuouslybutstopswhenhandentersdetectionzone,reversesolenoidelectricalconnections.
Faucet does not properly detect user:
To recalibrate, remove and reapply power or run faucet to maximum run time. Recalibration is complete when red light disappears.
QUICK TROUBLESHOOTING
Make sure detection zone and sensor are clear of debris, the power is on, and solid red light appears for 5 seconds after power-up. If these steps above do not solve the problem, visit chicagofaucets.com or contact customer service at 800/832-8783.
1
23
4
Connect Power: Self Sustaining Power System (SSPS)
i. Insert SSPS power supply
into control box upper
compartment. Attach
connectors, gray to gray,
black to black. Snap the
completed connections, into
the wiring harness as shown.
ii. Connect blue connector
on SSPS to blue
connector on the turbine
and tuck them into the
cavity as shown.
Connect Power: LTPS (DC)
1. Insert LTPS into control box
upper compartment, aligning
slots with compartment ribs.
Attach wiring connectors –
green to green, gray to gray.
2. Connect wiring connectors, gray to gray,
black to black. Snap into the wiring harness
Tuck the completed green connection into the
space as shown.
FOR EQ CONNECT UNITS
The wiring connectors are located on the
inside of the control box cover.
EQ Connect Devices - App Quick Start Guide
Download the EQ Connect app to your smartphone.
Search “eqconnect” on Google Play or on the App Store.
East, Floor 2, Sink 1
Open the app and your
bluetooth enabled phone
will scan for available
faucets. You can rename
faucets for easier
identification.
In the settings section,
adjust faucet and program
a hygiene-flush schedule.
The device section
provides information
on faucet usage and
downloadable logs.
The app allows you to
establish presets for faster
adjustment to multiple
faucets.