American Standard BERWICK 7430.15 Series User manual

BERWICK™
VESSEL LAVATORY FITTING
Installation
Instructions
M968642
Certified to comply with ANSI A112.18.1M
7430.15X
Turn off hot and cold water
supplies before beginning.
CAUTION
Adjustable Wrench Channel Locks
Regular Screwdriver
Phillips Screwdriver
Plumbers' Putty or Caulking
1INSTALL LAVATORY FAUCET
Seat SEAL (1) into under side of ESCUTCHEON RING (2).
Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4) through
ESCUTCHEON RING (2) and hole in mounting surface.
Seat ESCUTCHEON RING (2) with collar facing up into groove
in faucet base.
From below, install SUPPORT PLATE (7) GASKET (5) and MOUNTING
NUT (6) onto SHANK (4). Secure Faucet with MOUNTING NUT (6).
Before final tightening, adjust Faucet so that it is centered. Tighten
MOUNTING NUT (7) to complete mounting.
Note: For thick deck installations, the SUPPORT PLATE (7) can be omitted.
Recommended Tools
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
1
2
4
MOUNTING SURFACE
3
6
5
7
COLLAR
GROOVE
(FAUCET BASE)

M968642
3DRAIN INSTALLATION
Assembly GASKET (2) WASHER (3) and LOCKNUT (4)
onto DRAIN BODY (1). Tighten LOCKNUT (4) firmly.
Assembly TAILPIECE (5) to DRAIN BODY (1).
Apply a bead of PUTTY to underside of
DRAIN BODY FLANGE (1).
Feed DRAIN BODY (1) down through lavatory.
PUTTY
2
1
3
4
5
2MAKE WATER SUPPLY CONNECTIONS
LOOP SUPPLIES
IF REQUIRED
28"
1
2
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot and right supply to the Cold wall
supply. Use adjustable wrench to tighten
connections. Do not over tighten.
Faucet supplies are 28" long from faucet base.
Note: If additional supply length is required,
installer must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
Figure A.
COLD
COLD
HOT
HOT
Figure A.

M968642
Turn off hot and cold water
supplies before beginning.
CAUTION
OFF ON
COLD
HOT
4
5
TEST INSTALLED FAUCET
AND CHECK FOR LEAKS
SERVICE
1
2
3
COLD
HOT
With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate HANDLE (1) to flush water lines thoroughly.
Replace AERATOR (3).
6
1
2
4
5
6
2.5mm HEX KEY
REMOVE INSTALL
7
8
To remove or replace cartidge
Turn valve to OFF position.
Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).
Pull off HANDLE (3) and CAP (4).
Unthread CARTRIDGE NUT (5) and remove.
Pull out CARTEIDGE (6).
Inspect CARTRIDGE (6) and O-RINGS (7) for debris and clean
if necessary.
Clean MANIFOLD (8) and rinse clean.
Reinstall CARTRIDGE (6) and O-RINGS (7) onto MANIFLOD (8).
Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE ASSEMBLY (3).
If spout drips, operate handle several times from OFF to ON and HOT to
COLD position. Do not force - handles turn only 90˚.
3
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS: