Child Craft CRIB N BED W/ DECORATIVE ENDS User manual

CCH01760:07/00JCHE.p65
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH:812-883-3111-FAX:[phone]-http://www.childcraftind.com
child craftchild craft
child craftchild craft
child craft
ASSEMBLY DIRECTIONS AND PARTS LIST
ΦΦ
ΦΦ
ΦREADALLINSTRUCTIONSWITHCARE BEFORE STARTING THE ASSEMBLYPROCEDURE.
ΦΦ
ΦΦ
ΦYOU WILL NEED A STANDARD SLOTTED SCREWDRIVER AND THE ENCLOSED ALLEN WRENCH GGGG
GGGG
GG.
CRIB'N'BED W/
DECORATIVE ENDS
1
Thank you for choosing a Child Craft Crib'n'Bed! You have made a wise and important decision to furnish your nursery with furniture by Child Craft. Your
Crib'n'Bed has been designed for your child's comfort and your convenience, complete with a handy three-drawer chest or a two-drawer chest with
dressing area. Located beneath the Crib'n'Bed are two large blanket storage drawers. As your child g-r-o-w-s your Crib'n'Bed can be converted from
a"Crib"toa"Bed"andseparatechestcombinationforyearsofchildhoodusefulness.Qualitymaterialandworkmanshiphavebeenutilizedintheconstruction
of this Crib'n'Bed which will provide a sound and comfortable bed for your baby if properly assembled and maintained. Read all Warning and Caution
statements as well as Maintenance,Cleaning, Storage and Use directions. Some types of soft plastic toys, when placed in contact with finish materials
could damage the finish on fine furniture. Never place an object on the chest that could be obtained by the child while he is in the crib that could possibly
injure him, (no electrical appliances). Contents in open drawers could be accessible to a child in the crib, for this reason never leave drawers open.
Purchase a crib mattress 5 inches thick, which will enable the crib mattress to match the optional extension mattress for this unit available from Child
Craft, (forusewhenconvertedtoa"Bed"). DONOTuseawatermattresswiththisCrib'n'Bed. ThisCrib'n'Bedconformstoapplicableregulationspromulgated
by the Consumer Product Safety Commission and the American Society for Testing and Materials voluntary standard in effect at date of manufacture and
is certified by Juvenile Product Manufacturers Association.
PARTS ENCLOSED IN HARDWARE BAG: (noted when shown actual size)
A(9) Panhead Machine Screws
(actual size) B(1) Flathead Machine Screws (actual size) C(4) Steel Pins
(actual size)
LL(4) 4-Position Spring Hanger Brackets
(4) Panhead Machine Screws
C(actual size) E(6) Plastic Plug
Buttons AA
(12) Panhead Machine
Screw Plugs
(actual size)
(actual size)
KK
(12) Slotted Phillips
Wood Screws
(actual size)
EE
(3) Threaded Inserts
(actual size)
FF
(3) Panhead Machine
Screws
(actual size)
(1) Allen Wrench
GG JJ(4) Spring Hangers
(3) Panhead Machine Screws
HH
(actual size) (2 piece assembly)
THISCRIB'N'BED IS PACKEDIN FOUR (4)CARTONS:
1 - Foot Panel MM
MM
M
1 - Head Bottom Panel NN
NN
N
1 - Head Frame OO
OO
O
1 - Stationary Side PP
PP
P
1 - Folding Side QQ
QQ
Q
1 - Crib Spring RR
RR
R (with plastic pouch)
1 - Dust Bottom UU
UU
U
1 - Cushioned Cap Rail IIII
IIII
II (notched)
1 - Hardware Bag
1 - Chest FF
FF
F (assembled with three
small drawers" or "2 small drawers
with dressing area")
1 - Hardware Bag
Some models may include an ex-
tension spring that is optional on
other models. Be Sure You Have
Checked The Carton To Make
Sure This Extension Spring, If
Included, Is Not Thrown Away.
1 - Medium Drawer II
II
IParts
1 - Large Drawer JJ
JJ
JParts
1 - Center Drawer Guide Support KK
KK
K
Some models may include a foam
extension mattress that is optional
on other models. Be Sure That
You Have Checked The Carton
To Make Sure This Extension
Mattress, If Included, Is Not
Thrown Away.
1 - Wide Bed Rail GG
GG
G
1 - Narrow Bed Rail HH
HH
H
Carton #1 (of 4)
IdentifyandrecordyourCrib'n'Bedmodelidentificationnumberbeforeassembly,whichcanbefoundstampedontheunderneath
edge of the bottom rail of Stationary Side P.
RecordModelIdentificationNumber:______________________________________________.
Carton #2 (of 4) Carton #3 (of 4) Carton #4 (of 4)
16641, 16671

DIAGRAM 1
2CCH01760:07/00
Receiving hole & strike
plate for latch pin on Q
For installing Qusing A
EE on inside of Crib'n'Bed
FF on outside of Crib'n'Bed
For installing Qusing D
Insert C
For installing HH
O
For attaching Husing A
For inserting AA
Insert C
For inserting AA
Guide Block
N
Mattress Support
For installing Kusing D
Insert C
For inserting AA
Guide Block
Dowels
Dowels
For attaching Husing A
H
Mattress Support Mattress Support
Guide Block
Insert C
Dowel
Dowels
MFor inserting
AA
Drawer guide
K
G
Drawer guide
For attaching Husing D
For attaching Gusing D
For attaching
Gusing A
Dowels
Mattress Support
Guide Block
Dowels
For inserting AA
For attaching Gusing A
For installing Pusing A
EE on inside of Crib'n'Bed
FF on outside of Crib'n'Bed
For attaching Pusing D
Drawer guide

Carefullyremoveandlayoutall hardwareandpartsandmatch withPARTSENCLOSEDINHARDWARE BAGLISTandCARTONS#1,#2, #3and#4 LISTS.
Also check quantities. If you find a part missing, broken, or containing any sharp edges, contact your dealer or write to Child Craft, P.O. Box 444, Salem,
IN 47167-0444 (USA), ph. 812/883-3111, [email protected] for replacement parts or literature. Before making this contact refer to the identification
number you recorded on page one, (the number is found on the underneath edge of the bottom rail of Stationary Side
PP
PP
P ) , it is important that you include
this number with your request. DO NOT SUBSTITUTE PARTS! Read and Study the Assembly Instructions and Diagrams before you begin assembly to
facilitate the assembly of your Crib'n'Bed. Note: During the assembly process whenever using screws or bolts, check each with Hardware Parts List
(page 1) , letter and size identify by placing the screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size specified
in the assembly directions.
Set Aside and Store Until the Crib'n'Bed Is Converted To A "Bed":
★★★★
★★★★
★★TheseItemsAre Optional On Some Crib'n'Bed ModelsandMayNot Be Included:
ΦΦ
ΦΦ
ΦYou are advised to first build up drawers JJ
JJ
Jand II
II
Iby following instructions and
using drawer parts contained in Carton # 3, then set aside for later use.
CCH01760:07/00 3
★★
★★
★ 1 - Panhead Machine Screw HHHH
HHHH
HH
★★
★★
★ 6 - Plastic Plug Buttons EE
EE
E
★★★★
★★★★
★★ 1 - Foam Extension Mattress LL
LL
L
★★★★
★★★★
★★ 1 - Extension Spring SS
SS
S
★★
★★
★ 1 - Cushioned Cap Rail IIII
IIII
II
(notched)
{
If the Extension Spring and the Foam Extension Mattress are not included, you may order them from your local Child Craft dealer or call Child Craft at
[phone] and use your MasterCard or Visa to have these items sent to you via U.P.S. Have Model Idenification Number available if ordering, (recorded
onpageone.).
STEP1-PREPARATION
STEP 2-ATTACHMENT OF HEAD BOTTOM PANEL AND FOOT PANEL TO WIDE BED RAIL.
It is suggested that you place sheets of the packing material or a discarded
blanket or bed sheet over your floor covering to protect the finish of your
furniture. Refer to Diagram 1. Lay out parts NN
NN
N, OO
OO
O, HH
HH
H, KK
KK
K, GG
GG
Gand MM
MM
Mas
shown. Attach the Head Bottom Panel NN
NN
N, (drawer guide on inside) , to Wide
Bed Rail GG
GG
G, (smooth side on outside - mattress support on inside) , by inserting
Wide Bed Rail GG
GG
Gdowels into large holes provided in Head Bottom Panel NN
NN
N.
Refer to Diagram 2 . Place a Panhead Machine Screw AA
AA
Ainto each of the two
holes located in Head Bottom Panel NN
NN
N, insert a Plug AAAA
AAAA
AA into each of the two
holes located on inside of Wide Bed Rail GG
GG
G.Refer to Diagram 2. Pull out each
Machine Screw Ajust enough to allow the Plug AA to be fully inserted in hole.
Tighten each Machine Screw Auntil secure, but Do Not Overtighten. Attach
Foot Panel MM
MM
Mto Wide Bed Rail GG
GG
Gin same manner, insert two Panhead Machine
Screws AA
AA
Athrough the small holes located in Foot Panel MM
MM
M, and insert a Plug
AAAA
AAAA
AA into each of the holes located on the inside of Wide Bed Rail GG
GG
G. Pull out
each Machine Screw Ajust enough to allow the Plug AA to be fully inserted
in hole. Tighten each Machine Screw Auntil secure, but Do Not Overtighten.
DIAGRAM 2
A
AA
NG
STEP3-ATTACH CENTERDRAWER GUIDESUPPORT TO WIDE BEDRAIL &INSTALL NARROW BED RAIL.
Refer to Diagram 1 and MAIN DIAGRAM 2 . Place the two dowels located on end of Center Drawer Guide Support KK
KK
K into the two holes provided on
inside, (center) , of Wide Bed Rail GG
GG
G.Place a Panhead Machine Screw DD
DD
Dinto hole provided on top of Center Drawer Guide Support KK
KK
Kextending into
Wide Bed Rail GG
GG
G.Then attach Narrow Bed Rail Hto Head Bottom Panel NN
NN
N, Foot PanelM, and Center Drawer Guide Support KK
KK
Kby placing dowels
on Narrow Bed Rail HH
HH
Hinto holes provided in Head Bottom Panel NN
NN
N, dowel on Center Drawer Guide Support KK
KK
Kto be inserted in hole provided in center
of Narrow Bed Rail HH
HH
Hand the dowels located on remaining end of Narrow Bed Rail HH
HH
Hto be inserted in large holes located on Foot Panel MM
MM
M. Insert
a Panhead Machine Screw DD
DD
Dinto hole provided in Center Drawer Guide Support KK
KK
K, extending into Narrow Bed Rail HH
HH
H. Insert a Panhead Machine Screw
AA
AA
Athrough lower hole provided in Head Bottom Panel NN
NN
N, another Panhead Machine Screw
AA
AA
Ato be inserted through hole provided in Foot Panel MM
MM
M.
Refer to Diagram 2. Pull out each Machine Screw Ajust enough to allow the Plug AA to be fully inserted in hole. Tighten each Machine Screw Auntil
secure, but Do Not Overtighten.
MAIN DIAGRAM 2 PFStrikePlate
Latch Pin
Guide Block
Q
LL
JJ M
R
I
LL
O
AK
N
D
H
J
A
A
StrikePlate
Latch Pin
A
AA O
P
CLOSE UP VIEW
Note: DrawerPulls, (ifrequiredforyour
Crib'n'Bed Model), will be attached by
referring to Addendum Assembly In-
struction Sheet packed in Carton #2 . Note: Some models have a 2-Drawer Chest
with a dressing area on the top of the unit
(instead of as shown with 3 Small Drawers).
Guide Block Mattress
Support
Plastic
pouch

Note: The two-piece assembly of the 4-Position Spring Hanger Bracket LLLL
LLLL
LL.Before
installation, be sure the Moulded Plastic Backer is aligned with the 4-Position Spring
Hanger Bracket LLLL
LLLL
LL as shown in Diagram 1A. These items are shipped assembled,
in the unlikely event they should become detached during shipment, simply take the
PlasticBackerandalignwiththeholesintheMetalBracketandsnaptogethertocreate
an assembly as shown in the Parts Diagram. Important! All four plastic tabs on each
moulded plastic backer should project toward the metal hooks on 4-Position Spring
Hanger Brackets LLLL
LLLL
LL. If you should find a tab on an uninstalled 4-Position Spring
Hanger Bracket LLLL
LLLL
LL not so projected simply use a screwdriver to push tab forward
until it contacts the metal hook. If you find a plastic tab is not projected after 4-Position
Spring Hanger Brackets LLLL
LLLL
LL have been installed, simply place a small slotted
screwdriver underneath the plastic tab and pull forward until it contacts the metal
hook. Attach a 4-Position Spring Hanger Bracket LLLL
LLLL
LL (2 piece assembly) to both
wide spindles of the Stationary Side PP
PP
Pusing Slotted/Phillips Wood Screws KKKK
KKKK
KK
as shown in Diagram 1B . Also attach a 4-Position Spring Hanger Bracket LLLL
LLLL
LL to
both wide spindles of the Folding Side QQ
QQ
Qusing Slotted/Phillips Wood Screws KKKK
KKKK
KK
as shown in Diagram 1B . Tighten all Slotted/Phillips Wood Screws KKKK
KKKK
KK securely,
butdonotovertighten. CAUTION: NEVERREMOVE4-POSITIONSPRINGHANGER
BRACKETS LLLL
LLLL
LL, (in case you plan to store the crib'n'bed in later years) .
Leave the Spring Hanger Brackets LLLL
LLLL
LL attached with Slotted/Phillips
Wood Screws KKKK
KKKK
KK mounted - DO NOT REMOVE!
4CCH01760:07/00
STEP 3A - Install 4-Position Spring Hanger Brackets to the Stationary Side and Folding Side
JJ
LL
CLOSE UP VIEW
Lip depressed
DIAGRAM 1A
Holes to
receive
Slotted
Phillips
Wood
Screws
KK
Moulded
plastic
backer To remove Spring Hanger JJ
pressdownonlipwith thumbnailor
screwdriverandpullSpringHanger
JJ upward.
DIAGRAM 1B
LL
TeethingRail
ATTACHMENT OF:
4-Position Spring Hanger Bracket LLLL
LLLL
LL
to Stationary Side PP
PP
P
ATTACHMENT OF:
4-Position Spring Hanger Bracket LLLL
LLLL
LL
to Folding Side QQ
QQ
Q
TeethingRail
Hinge
PQ
LL
KK KK
Pilotholes
Pilotholes
Wide spindle of P(both ends)
Wide spindle of Q(both ends)
Latch Pin

CCH01760:07/00 5
STEP4-PLACECHEST AND INSERT LARGE DRAWER &MEDIUM DRAWER.
See Diagram 3 and MAIN DIAGRAM 2. Set Chest FF
FF
Fon top of Foot Panel MM
MM
Mend of frame, the three small drawers of Chest FF
FF
F, (Note: Some models
of crib'n'bed have a 2-drawer chest with a dressing-chest area on the top) , will face Narrow Bed Rail HH
HH
Hside of frame, the base of Chest FF
FF
Fnests within
bed frame. If you have not already built up drawers II
II
Iand JJ
JJ
Jdo so now by retrieving drawer parts and by following drawer build up assembly instructions,
all contained in Carton #3. Large Drawer JJ
JJ
Jand Medium Drawer II
II
Iwill now be inserted beneath Narrow Bed Rail HH
HH
H. Both drawers, since different sizes,
will need to be placed properly. NOTE: The drawer guides will fit into groove on each side of drawers, see Diagram 1.
Q
DIAGRAM 3
Q
PPA
F
F
BB
Strike plate Strike plate
M
A
Smalldrawer#3
H
I
Latch pin Pilotholes
(on some models)
Latch pin
H
I
A
M
Pilotholes
(on some models)
Smalldrawer#2
FlipTop
Top two
drawers of
chest are
removed.
Top drawer
of chest is
removed.
STEP 5-PLACEMENT OF STEEL PINS
Next place a Steel Pin CC
CC
Cinto each of the two small outer holes provided on top edge of Head Bottom Panel NN
NN
N, then place Head Frame OO
OO
Oon top of Head
Bottom Panel NN
NN
N, (align the two outer holes in the bottom edge of the Head FrameOwith the Steel Pins CC
CC
C. NOTE: The metal Strike Plate mounted on the
Head Frame OO
OO
Owill face inside of Crib'n'Bed, see DIAGRAM 1.
STEP 6-ATTACH STATIONARY SIDE
Note: Before attachment be sure you have recorded the identification number of this crib'n'bed which you will find located on the underneath edge of
the bottom rail of Stationary Side
PP
PP
P . Record this number for future reference if you have not already done so. See Diagram 1 and MAIN DIAGRAM
2. Place a Steel Pin CC
CC
Cin hole provided on top of Wide Bed Rail GG
GG
G, (near chest) . Refer to MAIN DIAGRAM 2. Place Stationary Side PP
PP
Pon top of Wide
Bed Rail GG
GG
G, engaging Steel Pin CC
CC
C. You will now need (2) Panhead Machine Screws AA
AA
A and (1) Panhead Machine Screw DD
DD
D.Place a Panhead Machine
Screw
AA
AA
Athrough the hole provided in Head Frame Oextending into end of top rail of Stationary Side PP
PP
P,insert a Plug AAAA
AAAA
AA into the hole located on the
bottom edge of the top rail of Stationary Side PP
PP
P, pull out Machine Screw AA
AA
Ajust enough to allow the Plug AAAA
AAAA
AA to be fully inserted in hole, tighten Machine
Screw AA
AA
Auntil secure, but do not overtighten, see CLOSE UP VIEW in MAIN DIAGRAM 2.
Place the other Panhead Machine Screw AA
AA
Athrough the hole provided in recessed part of back of chest FF
FF
Fto match the hole provided in end of top rail
of Stationary Side PP
PP
P. Insert a Plug AAAA
AAAA
AA into the hole located on the bottom edge of the top rail of Stationary Side PP
PP
P. Install as described with the previous
Panhead Machine Screw AA
AA
A . Tighten Panhead Machine Screw AA
AA
Auntil secure, but do not overtighten, See CLOSE UP VIEW in MAIN DIAGRAM 2. Note:
On crib'n'bed models which have a Chest with a Dressing area at the top, refer to Diagram 3.
Place a Panhead Machine Screw DD
DD
Dthrough the hole provided in the Head Frame OO
OO
Oextending into the end of the bottom rail of Stationary Side PP
PP
P.Tighten
securely, but do not overtighten.
Next, insert into each of the two holes provided in the top edge of the Head Frame OO
OO
Obottom rail a Panhead Machine Screw HHHH
HHHH
HH, also insert two Plugs
AAAA
AAAA
AA into each of the two holes located on the inside face of the Head Bottom Panel NN
NN
N. PULL OUT EACH MACHINE SCREW HHHH
HHHH
HH JUST ENOUGH TO
ALLOW THE PLUGS AAAA
AAAA
AA TO BE FULLY INSERTED IN HOLE, TIGHTEN EACH MACHINE SCREW HHHH
HHHH
HH UNTIL SECURE, BUT DO NOT OVERTIGHTEN.
See DIAGRAM 1.
STEP 7-ATTACH FOLDING SIDE
Refer to Diagram 1, MAIN DIAGRAM 2 and Diagram 3. On crib'n'bed models which have a chest with a dressing area refer to Diagram 1,
MAIN DIAGRAM 2 and Diagram 3. Note: Folding Side
QQ
QQ
Q hinges to outside of crib as shown on Diagram 3. Place a Steel Pin CC
CC
Cin hole provided
on top of Narrow Bed Rail HH
HH
H,near Chest FF
FF
F.Place the Folding Side QQ
QQ
Qon top of Narrow Bed Rail HH
HH
H, engaging Steel Pin CC
CC
C. Place a Panhead Machine
Screw AA
AA
Athrough hole provided in Head Frame OO
OO
O,at top, and into hole provided on the end of the rail of Folding Side QQ
QQ
Q.Insert a Plug AAAA
AAAA
AA into the hole
located on the bottom edge of the rail of Folding Side QQ
QQ
Q, pull out Machine Screw AA
AA
Ajust enough to allow the Plug AAAA
AAAA
AA to be fully inserted in hole. Tighten
Panhead Machine Screw AA
AA
Auntil secure, but do not overtighten. See Diagram 1 and MAIN DIAGRAM 2, and Close Up View.
Place a Panhead Machine Screw DD
DD
Dthrough hole in Head Frame OO
OO
Oand into the hole provided on end of bottom rail of Folding Side QQ
QQ
Q.
3 Drawer Chest 2 Drawer Chest
w/Dressing Area

Remove the two top drawers from Chest FF
FF
F(if your chest has 3 drawers).
Refer to the following directions for drawer removal and also refer
to Diagram 4. Note: Remove only the top drawer if your chest has
a dressing area. Place the one Flathead Machine Screw BB
BB
Bthrough hole
provided on inside of ChestFandinto hole provided in the end of rail of Folding
Side QQ
QQ
Q.Insert a Plug AAAA
AAAA
AA into the hole located on the bottom edge of the rail
of Folding Side QQ
QQ
Q.Pull out Flathead Machine ScrewBjust enough to allow
the Plug AAAA
AAAA
AA to be fully inserted in hole. Tighten Flathead Machine Screw BB
BB
B
until secure, but do not overtighten. See Diagram 1 and MAIN DIAGRAM 2.
(Be sure that you have placed the hinged portion of Folding Side
QQ
QQ
Q to outside
of crib as shown on Diagram 3 ) Important! Refer to Notice on Page
(8).
6CCH01760:07/00
STEP7-ATTACHFOLDINGSIDE(CONTINUED)
Insert (3) Panhead Machine Screws FFFF
FFFF
FF and (3) Threaded Inserts EEEE
EEEE
EE into the (3) empty holes in Head Frame OO
OO
O.Note: Threaded Inserts EEEE
EEEE
EE will
be placed into holes from the inside of the Crib'n'Bed and the Machine Screws FFFF
FFFF
FF will go into holes from the outside of Crib'n'Bed. Thread both parts
together and tighten securely using a flathead screwdriver and the enclosed Allen Wrench GGGG
GGGG
GG.Refer to Diagram 1 and MAIN DIAGRAM 2.
DIAGRAM 4 PRESSDOWNHERE
Then pull drawer out
Drawer Back
Drawer End
STEP 8-INSTALL DUST BOTTOM
Install Dust Bottom UU
UU
Uonto mattress supports on the inside face of the Wide
Bed Rail GG
GG
Gand Narrow Bed Rail HH
HH
H.Position the routs in the Dust BottomUU
UU
U
to mount over the guide blocks located on the matttress supports. See
Diagram 5.
DIAGRAM 5
U
Routs
Guide Blocks will be
inserted through
these routs.
P
GMattress support
Guide blocks
F
O
N
M
DIRECTIONS FOR REMOVAL OF SMALL
DRAWERS IN CHEST FF
FF
FWITH LOCK-IN
DRAWERS, ALSO SEE DIAGRAM 4.
Pull drawer open until it is stopped by the stop
lockon theplastic drawerglide. PRESS DOWNon
thereleasetabandpullthedrawerout. Note:Itwill
be necessary to PRESS DOWN on the release tab
located on each side of the drawer ends simulta-
neously for the lock-in mechanism to be released.
To reinsert the drawer into Chest FF
FF
F, simply align
eachsideofdrawerwiththedrawerglideandslide
into place..
STEP 9-INSTALL CRIB HANGERS&CRIB SPRING
Locate Crib Spring RR
RR
Rand the (4) Spring Hangers JJJJ
JJJJ
JJ. Note: Be sure
smooth side of Crib Spring RR
RR
Rwire is placed upward as illustrated in
Diagram 6. Insert Spring Hanger JJJJ
JJJJ
JJ into brackets attached to frame of
Crib Spring RR
RR
Ras shown. (A light blow with a hammer may be required to
fully engage Spring Hangers
JJJJ
JJJJ
JJ ) . Carefully install Crib Spring RR
RR
Rby placing
each of the (4) Spring Hangers JJJJ
JJJJ
JJ into a selected position in each of the
four 4-Position Spring Hanger Brackets LLLL
LLLL
LL mounted on Stationary Side
PP
PP
Pand Folding Side QQ
QQ
Q.Note: The lip of the Moulded Plastic Backer will allow
the Spring Hanger JJJJ
JJJJ
JJ to be placed with no difficulty. However, when you
decide on another placement position of Crib Spring RR
RR
Ryou will need to place
yourthumbnailorasmallscrewdriver,onthelipoftheMouldedPlasticBacker
and hold DOWN in order to raise Spring Hanger JJJJ
JJJJ
JJ from this position, see
Diagram 1A. NOTE: Refer to Step 3A for directions to project an inverted
tab on an installed 4-Position Spring Hanger Bracket
LLLL
LLLL
LL if needed. Follow
this same procedure whenever you change the Crib Spring RR
RR
Rto another
of the (4) positions.Note: When using the lowest of the 4-Positions; remove
the Dust Bottom UU
UU
Ufrom the unit and store for possible future use.
DIAGRAM 6
JJ
R
LL
PorQ
Insert all 4 Spring
Hangers JJ at
the same height
position.
Note: Mattress & Crib Spring RR
RR
Rmust be removed to gain
accesstothePlasticPouchwhichismountedtotheunderside
of Crib Spring RR
RR
R.
STEP9A-STOREASSEMBLYDIRECTIONSFORFUTURE USE
After completing the assembly process, and after making yourself aware of
theWarnings,Cautions,Cleaning,Storage,UseandMaintenanceofcrib'n'bed,
store the assembly directions in the plastic pouch which was pre-attached
to the underneath side of Crib Spring RR
RR
R. Entrance will be gained by removing
mattress and Crib Spring RR
RR
R. For future referral to the assembly directions you
must remove the mattress and Crib Spring RR
RR
Rto access the plastic pouch to
remove the stored assembly directions.
DO NOT PLACE EXCESS HARDWARE OR
TOOLSINPLASTICSTORAGEPOUCHASIT
COULD PRESENT DANGER TO A SMALL
CHILD IF RETRIEVED.
IMPORTANT! BESUREALL SCREWS ANDBOLTSARE TIGHTENED AT
THISTIME, SECURE,BUT DONOT OVERTIGHTEN. A PERIODIC CHECK
SHOULDBEMADEOFALLSCREWSANDBOLTSINTHISUNITTOBESURE
THEYREMAINTIGHTENED!
IMPORTANT!CHECKALLCARTONSANDPACKINGMATERIALBEFORE
DISCARDINGTOBESUREYOUHAVEREMOVEDALLCRIB'N'BEDPARTS
ANDHARDWARE.

CCH01760:07/00 7
STEP10A-ATTACHDRAWER PULLS (IFREQUIRED)
SeeAddendum Sheet inCarton No. 2 for installing drawerpulls, againonly
if required on some models.
STEP10B-MATTRESS PLACEMENT
Place a purchased mattress on Crib Spring Rand "Crib" is ready for use.
(For compatibility with extension spring and extension mattress you are
advised to purchase a 5" thick crib mattress.) Some models of crib'n'bed
will be packed with the extension spring and extension mattress for use
when converting to "Bed", and other models will not. If not included you
may purchase both the extension spring and extension mattress from Child
Craft, 812/883-3111. If purchasing, have your model number and a charge
card handy when placing your phone call.
See pages (8 and 9) for directions to convert "Crib" to a "Bed". Also
it is extremely important to make yourself aware of the following
Warnings and Cautions regarding the use of your Crib'n'Bed.
ΦΦ
ΦΦ
ΦFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH.
ΦΦ
ΦΦ
ΦREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB'N'BED. KEEP INSTRUCTIONS FOR
FUTURE USE. A plastic pouch is attached to crib spring for permanent storage of instructional
literature.
ΦΦ
ΦΦ
ΦBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR DAMAGED HARDWARE, LOOSE
JOINTS,MISSINGPARTSORSHARPEDGES.DONOTUSECRIBIFANYPARTSAREMISSINGOR
BROKEN. ASK YOUR DEALER OR WRITE TO CHILD CRAFT, P.O. BOX 444, SALEM, IN (USA)
47167-0444, (812/883-3111), [email protected] FOR REPLACEMENT PARTS AND IN-
STRUCTIONAL LITERATURE IF NEEDED. INCLUDE MODEL IDENTIFICATION NUMBERS WITH
YOUR REQUEST WHICH YOU RECORDED ON PAGE ONE. DO NOT SUBSTITUTE PARTS.
ΦΦ
ΦΦ
ΦAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.
ΦΦ
ΦΦ
ΦDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE SIDE IS IN RAISED AND
LOCKED POSITION WHENEVER CHILD IS IN CRIB.
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET MATTRESS TO LOWEST
POSITION(IFAPPLICABLE)ANDREMOVEBUMPERPADS,LARGETOYSANDOTHEROBJECTS
THAT COULD SERVE AS STEPS FOR CLIMBING OUT.
ΦΦ
ΦΦ
ΦNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS
BECAUSE THEY CAN CAUSE SUFFOCATION.
ΦΦ
ΦΦ
ΦDO NOT USE A WATER MATTRESS WITH THIS CRIB.
ΦΦ
ΦΦ
ΦREPLACETEETHINGRAIL(S)IFDAMAGEDORLOOSE.(IFCRIBISEQUIPPEDWITHTEETHING
RAILS.)
ΦΦ
ΦΦ
ΦSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND A
CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS
OVER A CRIB OR ATTACH STRINGS TO TOYS.
ΦΦ
ΦΦ
ΦDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY
STRANGLE A CHILD.
ΦΦ
ΦΦ
ΦIF REFINISHING, USE A NONTOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.
ΦΦ
ΦΦ
ΦWHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE ANY ITEM ATTACHED WITH WOOD
SCREWS.
ΦΦ
ΦΦ
ΦREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB AREA WHEN YOUR CHILD IS
BEGINNING TO PUSH UP ON HANDS AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER
OCCURS EARLIEST. THESE TOYS CAN CAUSE STRANGULATION!
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE HEIGHT OF 35 INCHES (90 CM) THE
CRIB SHALL NO LONGER BE USED. (THIS “CRIB” SHOULD BE THEN CONVERTED INTO A
“BED” OR PLACE CHILD IN A YOUTH OR REGULAR BED.)
ΦΦ
ΦΦ
ΦALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING REGULARLY,
BEFORE PLACING THE CHILD IN THE CRIB OR BED, THAT EVERY COMPONENT IS PROPERLY
AND SECURELY IN PLACE.
WARNING
▲
!

ΦΦ
ΦΦ
ΦUPON COMPLETION OF ASSEMBLY BE SURE ALL SCREWS, BOLTS AND FASTENING
DEVICES HAVE BEEN TIGHTENED SECURELY. A FREQUENT CHECK SHOULD BE MADE OF
ALL SCREWS, BOLTS AND FASTENING DEVICES AND TIGHTEN IF NEEDED.
ΦΦ
ΦΦ
ΦANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES (69 CM), BY 51-5/8
INCHES (131 CM), WITH A THICKNESS NOT EXCEEDING 6 INCHES (15 CM). (FOR COMPATIBIL-
ITY WITH THE OPTIONAL EXTENSION MATTRESS, PURCHASE A CRIB MATTRESS 5 INCHES
THICK (12.8 CM). THE DIMENSIONS OF THE MATTRESS SHALL BE TAKEN FROM SEAM TO
SEAM OR EDGE WHERE APPROPRIATE.
ΦΦ
ΦΦ
ΦWHEN PLACING OBJECT ON CHEST, (WHEN USED AS A CRIB), BE SURE THERE IS NOTHING
THAT COULD BE OBTAINED BY THE CHILD THAT WOULD INJURE HIM, (NO ELECTRICAL
APPLIANCES). USE EXTREME CAUTION WITH WHATEVER YOU PLACE ON THE CHEST, ONLY
PLACE OBJECTS ON CHEST THAT WOULD BE SAFE FOR BABY. CONTENTS IN OPEN DRAW-
ERS COULD BE ACCESSIBLE TO CHILD IN CRIB, NEVER LEAVE DRAWERS OPEN.
Notice:Forthesecurityofyourchild,thedropsidelatchassembliesonthisunithavebeensecured
withaliquidfastener.Thisisdonetoeliminatethepossibilityofthechildunscrewingandpossibly
swallowingapartfromthisassembly.Ifyouexperiencedifficultywhenyoufirstattempttooperate
(these)latches,clampontotheknobwithpliersandpullstraightoutuntilthelatchassemblyworks
freely. (Note: protect the knob with a cloth before clamping with pliers.)
8CCH01760:07/00
CAUTION
MAINTENANCEOF YOUR CHILDCRAFT CRIB'N'BED: Uponcompletionof assemblybesureall screws,boltsandfastening deviceshavebeen tightened
securely. A frequent periodic check should be made of all screws, bolts and fastening devices and tighten if needed. Before each usage or assembly,
inspect Crib'N'Bed for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use Crib'N'Bed if parts are missing or broken. Contact your
dealer or Child Craft for replacement parts and instructional literature if needed. Refer to the identification number you previously recorded on page (1)
and include this number when contacting your dealer or Child Craft. DO NOT substitute parts. DO NOT make any alteration to this Crib'N'Bed.
CLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT CRIB'N'BED: Any cleaning required can be done with a mild dishwashing solution using a soft
cloth. After cleaning, all surfaces should be dried thoroughly, again using a soft cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR
COARSERAGSSHOULDBEUSEDTOCLEANTHISFINEFURNITURE.
STORAGEANDUSEOFYOURCHILDCRAFTCRIB'N'BED: KEEPTHEASSEMBLYINSTRUCTIONSWITHYOURCRIBFORFUTUREREFERRAL. A
plastic pouch was factory attached to the Crib'N'Bed Crib Spring for permanent storage of the assembly instructions. We CAUTION you not to place excess
hardware or tools in the plastic holder as they could present danger to a small child if retrieved. When storing crib use CAUTION as extreme temperature
orhumiditycouldbeharmfultothewoodandfinishmaterials.Moistureandheatareharmfultofinishmaterials,forthisreasonuseCAUTIONwhenavaporizer
is in use, always aim vapor stream away from crib as well as away from any other wood furniture item. Some types of soft plastic toys, when placed
in contact with finish material could damage the finish on fine furniture.
DIRECTIONS FOR CONVERSION OF "CRIB" TO A "BED"
When your child reaches a height of (35) inches (or before) you have the option to convert crib to a "Bed".
On page (3) you were told to set aside and store until your crib is converted to a "Bed":
ΗΗ
ΗΗ
Ηand ΗΗΗΗ
ΗΗΗΗ
ΗΗ You will now need these items for the conversion process.
If the Extension Spring and the Foam Extension Mattress are not included, you may order them from your local Child Craft dealer or call Child Craft at
[phone] and use your MasterCard or Visa to have these items sent to you via U.P.S. Have Model Idenification Number available if ordering, (recorded
onpageone.).
★★
★★
★ 1 - Panhead Machine Screw HHHH
HHHH
HH
★★
★★
★ 6 - Plastic Plug Buttons EE
EE
E
★★★★
★★★★
★★ 1 - Foam Extension Mattress LL
LL
L
★★★★
★★★★
★★ 1 - Extension Spring SS
SS
S
★★
★★
★ 1 - Cushioned Cap Rail IIII
IIII
II
(notched)
★★THESEITEMS AREOPTIONAL ON SOME MODELS AND MAY NOT BE INCLUDED. {
STEP 11-REMOVE STATIONARY SIDE &FOLDING SIDE
Store everything you remove in case you will want to convert "Bed" back into a "Crib" in later years. Remove both Stationary Side PP
PP
Pand Folding Side
QQ
QQ
Q. Use Steps 5, 6, 7, 8 and 9 in reverse order to direct you in the removal of both sides PP
PP
P& QQ
QQ
Q, Head Frame OO
OO
Oand Crib Spring RR
RR
R.
STEP 12-INSTALL CUSHIONED CAP RAIL
Remove Chest FF
FF
Fand set on floor in a convenient location. Install the Cushioned Cap Rail IIII
IIII
II (notched) as shown in Diagram 14. The Cushioned Cap
Rail IIII
IIII
II will be installed to the top edge of Foot Panel MM
MM
M.First, check to be sure Cushioned Cap Rail IIII
IIII
II has an equal overhang on both ends, then press
it down over the top edge until it is fully seated. Note: notches are to be placed to inside of "Bed".

CCH01760:07/00 9
STEP13-REMOVE STATIONARY SIDE &FOLDING SIDE
IMPORTANT! Read STEP13completelybefore continuingany further.
FIRST: Locate three Panhead Machine Screws HHHH
HHHH
HH and Head Frame OO
OO
O. Remove the three Panhead Machine Screws AA
AA
Afrom the Head Bottom Panel
NN
NN
Nvery carefully, see Diagram 12 . Try to prevent the Bed Rails GG
GG
Gand HH
HH
Hfrom disengaging from the Head Bottom Panel NN
NN
N.
SECOND: Mount Head Frame OO
OO
Oto the outside face of Head Bottom Panel NN
NN
N. (The Head Frame
OO
OO
O will have the Strike Plate mounted away from the mattress
area.) Insert three Panhead Machine Screws HHHH
HHHH
HH through the Head Frame OO
OO
O,then through the Head Bottom Panel NN
NN
Nand into the Bed RailsGand
HH
HH
H. Insert a Plug AAAA
AAAA
AA into each of the two holes located on the inside of the Wide Bed Rail
GG
GG
G. (Note: After removing Machine Screws
AA
AA
A the Plugs
AAAA
AAAA
AA may have stayed in the holes.) Pull out each Machine ScrewHH just enough to allow the Plug AA to be fully inserted in the hole. Tighten each
Machine Screw HH until secure, but do not overtighten. Reattach the Narrow Bed Rail HH
HH
Hin the same manner.
THIRD: Place a Plastic Plug Button EE
EE
Einto each of the four holes shown in Diagram 13 . Also place a Plastic Plug Button EE
EE
Einto the outside face of Chest
FF
FF
Fat the location of where the Stationary Side PP
PP
Pand the Folding Side QQ
QQ
Qwere attached as a "Crib".
DIAGRAM 12
G
Install E
N
H
Large Storage Drawer
Mattress Support
Guide Block
Remove these
three screws A
very carefully
Mattress Support
G
H
Both faces
N
Install E
Insert the (3)
Panhead Machine
Screws HHHH
HHHH
HH thru
receiving holes in
Head Frame OO
OO
O,
then thru Bottom
Panel NN
NN
Nand into
Bed Rails GG
GG
G&HH
HH
H.
Secure with Plugs
AAAA
AAAA
AA. See Step
13.
O
Strike plate
DIAGRAM 13
Remove Spring Hangers JJJJ
JJJJ
JJ from Spring RR
RR
R. Also remove Dust
Bottom UU
UU
U.Place Crib Spring RR
RR
Rinto assembled unit using guide
blocks to locate Crib Spring RR
RR
R. See Diagram 1 and MAIN DIAGRAM
2. Note: Crib Spring RR
RR
Rwill now rest on wooden mattress supports.
STEP13A-REMOVE SPRING HANGERS
& DUST BOTTOM
STEP14-PLACEMENT OF EXTENSION SPRING
EXTENSIONMATTRESS&CRIBMATTRESS
Place the optional Extension Spring and the optional Extension
Mattress into place where Chest FF
FF
Fwas removed. If your model
Crib'n'Bed did not include an Extension Spring or Extension Mat-
tress you may order them from your dealer or Child Craft at (812)
883-3111 by using your MasterCard or Visa charge to have these
items sent to you. Again, after assembly is complete place this set
ofassembly instructionsback intothe PlasticPouch factory mounted
to Crib Spring RR
RR
Rfor permanent storage. Place crib mattress on crib
spring and Your "Bed" is now ready for use.
DIAGRAM 14 NOTE:Notches
are to be placed to
inside of "Bed".
H
M
Lower drawer
Shown as "Bed"
II
To Operate Latch Pins on Folding Side QQ
QQ
Q, when set up as a “Crib”, follow directions listed below. Refer to Main Diagram 2, Diagram
3 and the NOTICE listed on Page 8. Place a hand on each latch pin, while pulling out, slide each handle toward the middle of crib, the latch pins
will now be free to allow the folding side to be placed in the Down Position. Repeat the same operation to place Folding Side Qin Upward Position,
only after pulling latch pins out and to middle of crib, align with receiving hole in strike plate located on inside of Chest Fand on Head Top Panel O,
release latch pins into receiving holes. Check to be sure the Latch Pins are in proper position before leaving your baby in crib. Always check to be
sure the side, when in the Upward Position, is secure. IMPORTANT: See Notice regarding latch pins on page 8.
IMPORTANT! BESUREALLSCREWSARETIGHTENEDATTHISTIME,SECURE,BUTDONOTOVERTIGHTEN. APERIODICCHECKSHOULDBEMADE
OFALL SCREWS IN THIS UNITTO BE SURETHEY REMAIN TIGHT.
IMPORTANT! Refer to Warnings & Cautions listed on pages 7 and 8, Maintenance, Cleaning Instructions, Storage and Use of your Child
Craft Crib'n'Bed listed on page 8. Store all parts not used, for possible future use in case you will want to convert “Bed” back into a “Crib”.
Place assembly directions in storage pouch mounted on Crib Spring RR
RR
R..
..
.
In the event you choose to convert "Bed" back into a "Crib" at a later date, first remove Head Frame OO
OO
Oby reversing procedure in Step
13. Second, Cushioned Cap Rail IIII
IIII
II must be removed from the top edge of Foot Panel MM
MM
M. Start by pulling up on one end of Cushioned
Cap Rail IIII
IIII
II, (if you have difficulty, carefully use a slotted screwdriver tip to pry between the top edge of the Panel MM
MM
Mand Cushioned
Cap Rail IIII
IIII
II). Be very careful to not damage either part. Then proceed with Steps (4) thru ( 9) for “Crib” buildup.
CHILDCRAFTINDUSTRIES,INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: [phone]
http://www.childcraftind.com
child craftchild craft
child craftchild craft
child craft made in usa