Cisco SPA112 User manual

Copyright © 2012 Jaguar Telecom Version 1.8
Cisco SPA 112
Setup & User Guide

Copyright © 2005-2012 Jaguar Telecom Version 1.8 Page 1 of 8
Copyright
Copyright © 2005-2012 Jaguar Telecom Ltd.
Information in this document is subject to change without notice. No part of this
document may be reproduced, transmitted or stored in a retrieval system, in any form
or by any means, electronic or mechanical, for any purpose, without the written
permission of Jaguar Telecom Ltd.
Contents
Contents'
Copyright................................................................................................................1!
Contents...................................................................................................................... 1!
1!Introduction.......................................................................................................... 2!
1.1!Shipping List .....................................................................................................2!
1.2!Additional equipment required .............................................................................2!
2!Initial configuration .............................................................................................. 3!
2.1!Network Assumptions ........................................................................................3!
2.2!SPA112 Lights ...................................................................................................3!
2.3!SPA112 Back Panel ............................................................................................4!
2.4!Network Setup...................................................................................................4!
2.5!Router ..............................................................................................................5!
3!Check the operation of the SPA112......................................................................... 6!
3.1!Registration and Account activation......................................................................6!
3.2!Phone Operation................................................................................................6!
3.3!Check Ringing ...................................................................................................6!
3.4!Finished ............................................................................................................6!
4!Trouble Shooting .................................................................................................. 6!
4.1!SPA112 Lights ...................................................................................................6!
Power Light (far left) ...............................................................................................6!
Internet Light .......................................................................................................... 7!
Phone Light ............................................................................................................7!
4.2!No Audio..........................................................................................................7!

Copyright © 2005-2012 Jaguar Telecom Version 1.8 Page 2 of 8
1Introduction
This document describes how to install the Cisco terminal adaptors.
This document is applicable to the following devices:
Model Number
Description
SPA 112
2 FXS Port Terminal Adaptor
We use a sophisticated auto provisioning system to pre-configure and test all the devices
we supply.
This has the following advantages:
•Easiest possible installation
•Elimination of configuration errors caused by mistyping
•The ability to seamlessly apply configuration and firmware updates
•The ability to apply custom and site specific changes to your configuration.
The document is in two parts, the first section is the setup of a new Cisco as supplied
pre-configured for your use
1.1 Shipping List
Quantity
Description
1
Cisco SPA112 (Terminal Adaptor)
1
UK Power Supply
1
Ethernet Cable
1
UK Telephone Socket converters
1
This Setup Guide
1.2 Additional equipment required
•Operational Ethernet LAN with ADSL router providing Internet connectivity
•Standard UK telephone(s)

Copyright © 2005-2012 Jaguar Telecom Version 1.8 Page 3 of 8
2Initial configuration
The device comes pre-configured with all the settings pre-loaded. It is only necessary to
follow the network setup process described below.
2.1 Network Assumptions
•The SPA 112 will be connected to the LAN side of a broadband Ethernet router.
•The router is in NAT (network address translation) mode and the LAN side of the
router is using private IP address (usually 192.168.x.x).
•It is assumed that the router will act as a DHCP server and hand out IP addresses
for devices on the LAN side.
•It is also assumed that the router DHCP server will also provide the IP addresses
of DNS servers to use.
•It does not matter if the broadband has a static or dynamic IP address.
2.2 SPA112 Lights
Light
D e s cri p tio n
Phone 1
Phone 2
Steady green—On hook .
Slow flashing green—Off ho ok .
Off—Port not r e ady .
In terne t
Flashing green—Transmitting or receiving data th r o ugh
the WAN p or t .
Off—No l i nk .
Sys t e m
Steady green—System r e ady , IP address ac quir e d .
Slow flashing green—Acquiring IP addr e ss . (By def a ult ,
uses DHC P .)
Fast f l a s h i n g green—Upgrading fi rm wa r e .
Off—No power or system can not boot up.

Copyright © 2005-2012 Jaguar Telecom Version 1.8 Page 4 of 8
2.3 SPA112 Back Panel
Fe a tu r e
D e s cri p t i o n
Re s e t
No not press the reset button under any
circumstances. This will permanently disable the
operation of the unit .
Phone 1 ,
Phone 2 (Gra y)
Connect to an analogue phone, using the UK Phone
adaptor provided
Internet (Blue)
Connect to a broadband network device (DSL or
cable mo dem ) or a network r out e r , using an E thernet
cable.
Power
Connect to a power source, using the pr ovide d
power adapt e r .
2.4 Network Setup
Please follow the instructions below
•Connect the Internet cable directly into your ADSL router.
•Plug in the phone(s) that you are going to use now, using the UK/RJ11 phone
adaptors if necessary.
•Insert power lead. Power on the Cisco and wait for 60 seconds

Copyright © 2005-2012 Jaguar Telecom Version 1.8 Page 5 of 8
You should now have a solid green power light, and also a solid green Internet light, If
not you must correct the problem with the DHCP before proceeding.
2.5 Router
Your router should be set up to perform NAT (Network Address Translation) and act as a
DHCP server (or have a standalone DHCP server somewhere on you network). These
features are normally enabled by default on most routers.
An IP address will be allocated to the phone automatically when you plug the Ethernet
cable from your phone into your router.
Please note: you should ensure the following ports are not blocked by the firewall within
your router:
Far end ports
oUDP Ports 4144 and 4244
oUDP Ports 10000 to 32767
oHTPPS Port 443
oSys Log Port 514
oHTTP Port 80
oDNS Port 53
oNTP Port 123
Local ports
Outbound requests to standard services will be from a random port (as for a PC)
The following ports will be used to receive SIP and RTP packets
oUDP Ports 5061 and 5062
oUDP Ports 4241 to 4280
oUDP Ports 10000 to 32767
It is our strong recommendation to minimise the number of firewall rules required on the
router. This will reduce the CPU load on the router and also future proof the site from
future additions to the service.
This can be simply implemented by a single rule which allows all (UDP and TCP) traffic to
and from 154.51.129.0 netmask 255.255.255.0 - this is a /24 network
The system can support both static and dynamic IP addresses.

Copyright © 2005-2012 Jaguar Telecom Version 1.8 Page 6 of 8
3Check the operation of the SPA112
3.1 Registration and Account activation
Check the Phone 1 and Phone 2 lights on the Cisco, for one subscription on the Cisco you
should have one light, and 2 lights for 2 subscriptions.
Logon to www.telephony-cloud.com. Your username and password are on MySettings
Sheet
You should see the phone displayed in Blue and Mauve as below.
If you hover over the phone the tool tips show the IP address and the time of the last
registration.
There should be a small “p” below the phone to indicate that the Cisco is using the
Jaguar Telecom Outbound Proxy Server.
3.2 Phone Operation
Dial 1451
You should hear a message with technical details about your Phone
3.3 Check Ringing
Phone the number from a normal phone to check that ringing is operational.
If the phone does not ring, check if you need a master phone adaptor and try an
alternative phone
3.4 Finished
You may now enjoy your new service, there is no need to read beyond this page.
4Trouble Shooting
4.1 SPA112 Lights
The Power, Internet and at least one phone light must be on solid for successful
operation of the unit.
Power Light (far left)
Off
•Unit has no power
Solid light
•Unit operating properly

Copyright © 2005-2012 Jaguar Telecom Version 1.8 Page 7 of 8
Slow Blinking ( 0.5s ON, 0.5s OFF )
•System Initialisation
•Looking for DHCP
long, short, short, off for 2 seconds
•No Ethernet link detected
Very Fast Blinking , for 30 seconds
•The unit is being upgraded, NO NOT DISCONNECT OP UNPLUG the unit until
it has finished.
Internet Light
Off
•No Ethernet link detected
Solid light
•Ethernet link detected
Random flashing
•Network has data flowing
Phone Light
Off
•Phone line is not configured or is not registering properly with the Jaguar Telecom
Service
Solid light
•Phone line is registering properly with the Jaguar Telecom Service, and is ready
for use
Show flashing
•Phone is in use or off hook.
4.2 No Audio
If you cannot hear audio during a call please check the firewall settings of your
router are correct.