Cisco TelePresence MX700 User manual

78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. http://www.cisco.com/go/mx-docs
Installation guide
for Cisco TelePresence MX700 Single Camera
on a free standing oor stand or a oor stand secured to the wall

78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 2
Manpower
We recommend three people working together
to mount the system. Follow local regulations.
Dimensions
Height: 1631 mm / 64.3in.
Width: 2517 mm / 99.1in.
Depth: 156 or 215mm / 6.2 or 8.5in. (wall secured)
920mm / 36.3 in. (free standing)
Weight: 154kg / 340 lb
Floor stand secured to the wall
This guide covers the floor stand mounted MX700 with
single camera, in either the free standing or wall secured
configurations.
Free standing floor stand
Room setup
Explore the Cisco Project Workplace to find
inspiration and guidelines when preparing your
office or meeting room for video conferencing,
http://www.cisco.com/go/projectworkplace
User documentation
The user documentation for this product,
including compliance and safety information,
can be found on the Cisco web site,
http://www.cisco.com/go/mx-docs

78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 3
Lift off box L/M. Lay box A flat on the floor and remove the lid.
2
1Open the plastic snap locks and remove the side walls.
Packaging
L/M
A
D
Boxes are labeled A to M. This guide refers to the labels.
A M
...
B+E-G Shows which boxes are inside.
Tools and screws are in this box.
Screws
Countersunk
Allen key, 4 mm
M6x12M6x35M6x90
Pan
Allen key, 4 mm
M6x12
Pan
Torx T20
PT4x10
M4x8
Pan
Allen key, 2.5mm
EMC Class A declaration
WARNING: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
声明
此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.

1Remove covers from floor stand parts
A
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 4
Set aside the covers. They will be
replaced when the system is fully
assembled and tested (step 20).
Front

2Assemble floor stand
B
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 5
Fasten the upper and lower center parts simultaneously,
first on one side; then on the other.
Six screws from the back
and two from the top.
8 × M6x12
(countersunk)
8 × M6x12
(countersunk)

3Fasten center bracket
B
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 6
Front
2 × M6x12 (pan)

4Secure floor stand
B
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 7
Option A:
Mount the feet to the floor stand to allow it to be free standing
4 × M6x35
(countersunk)
Front
Option B (secured to the wall) is described on the next page.

4Secure floor stand
C
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 8
Option B:
Use the wall brackets provided to secure the floor stand to the wall
The system must be installed by qualified
personnel, in accordance with state and local
building regulations.
The wall and mounting hardware must be
able to safely support the product.
Side view
94 mm / 3.70 in. 37 mm / 1.46 in.
The wall brackets have two mounting positions.
Position the brackets the way that suits your
room the best.
1 2 Place the floor stand in the wall brackets
without fastening it. Move the floor stand and
wall brackets into position.
The wall brackets can be fastened through
any of the horizontal slots. Mark the required
screw hole positions on the wall.
Fasten each wall bracket in a secure manner
ensuring that the wall’s structure is sufficient
to support the system (screws/mounting
hardware not provided; not shown in
illustration).
3Fasten the floor stand to
the wall brackets with the
four screws (provided).
4 × M6x12 (pan)
Front
Option A (free standing with feet) is described on the previous page.

5Read this before you mount the monitors
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 9
65 kg / 144lb
The monitors are heavy. We recommend
three people working together to mount
the monitors. Two people should lift the
monitor using the handles as described
below; the other person must help
stabilizing the monitor and check that
the monitor enters the slots properly.
Applies to systems that are secured
to the wall:
To assure that the camera
can move freely, fasten two
bumpons on the rear of the top
profile, close to the camera.
Avoid trapping your fingers!
Use the lifting handles at the bottom of
the monitor.
The screws with wing nut, which you
can see from the sides of the monitor,
must enter the center slot on each
side of the floor stand.

6Lift left monitor onto floor stand
D
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 10
65 kg / 144lb
Make sure that the screw
with wing nut enters the
center slot on both sides.
Do not let go of the monitor
before it is securely placed
on the floor stand.
1
Rear view
Tighten the wing nuts
on both sides. They are
accessed from the sides
of the monitor.
2
Rear view

7Fasten left monitor to floor stand and connect power cable
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 11
Enter four screws from
front and four screws from
underneath. Then, tighten
all screws.
1
A power cable is strapped
at the rear of the monitor.
Connect it to the close-by
socket.
Let the other end hang
freely. It will be connected to
the right monitor in step 9.
2
4 × M6x90
(countersunk)
4 × M6x35
(countersunk)

8Lift right monitor onto floor stand
D
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 12
65 kg / 144lb
Tighten the wing nuts
on both sides. They are
accessed from the sides
of the monitor.
2
Make sure that the screw with
wing nut enters the center slot on
both sides.
Keep the outer side a bit lower than
the side toward the other monitor
when lowering the monitor onto the
floor stand.
Do not let go of the monitor before it
is securely placed on the floor stand.
1Rear view
Rear view

9Fasten right monitor to floor stand and connect power cable
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 13
Enter four screws from
front and four screws from
underneath. Then, tighten
all screws.
1
Connect the loose end of
the power cable from step 7
to the close-by socket at the
rear of the right monitor.
If the system is placed close
to the wall, you must reach
the socket from below.
Make sure the power switch
next to the socket is in its
ON position.
2
4 × M6x90
(countersunk)
4 × M6x35
(countersunk)

10Remove support handles
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 14
Unscrew the screws (4 × M4x8)
and remove the support handles.

11  Mount joining bracket
EBox E is placed uderneath box C.
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 15
7 × M6x12 (pan)
Place the joining bracket in the
channel. Make sure it aligns with
the channel at top.
Open the lever.
Push down the lever to
horizontal position.
12
3 4

12  Mount back cover
E
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 16
Mount the back cover. If the system is
placed close to the wall the back cover
must be mounted from above.
1
2
Lower the back cover toward the
system. The cover snaps to magnets.
Lead the guidance pins on the back
cover into the holes.

13Organize pre-mounted cables
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 17
Organize the cables that are placed in the channel on top of the monitors.
Lead the cables to the right, and place them as shown in the illustration.
The cables will be connected in steps 14, 16 and 17.
Left
monitor
Right
monitor
Loudspeaker
cables 3-5
Camera
cables
Monitor
cables
Loudspeaker
cables 1-5
PoE injector
cable
×3 ×5

14  Connect cables to right monitor and PoE injector
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 18
Power over Ethernet injector
Ethernet
Right monitor connector panel
HDMICOLOR
CALIBRATION 12
DO NOT
REMOVE
USB (type B)HDMI
SWITCH

15Mount camera (page 1 of 2)
F, G
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 19
Insert the stud underneath the
frame. Align its screw hole with
the upper right screw hole of the
camera.
Fasten the stud to the top profile
with one screw from above.
Repeat this step for the left side.
2 × M4x8 (pan)
123
Insert the camera. 1 × M4x8 (pan)

15Mount camera (page 2 of 2)
F, G
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Floor stand
Page 20
Enter the camera cover in the clips
at the bottom, and align it with the
back panels. The cover snaps to
magnets.
2 × M4x8 (pan)
4 5