Cisco 8011-2X2XP4L Manual

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service
Endpoint Router
First Published: 2023-12-08
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1721R)
©2023 Cisco Systems, Inc. All rights reserved.

CONTENTS
Safety Warnings 1
CHAPTER 1
Standard Warning Statements 1
Safety Guidelines for Personal Safety and Equipment Protection 3
Safety Precautions for Module Installation and Removal 3
Safety with Electricity 4
Cautions and Regulatory Compliance Statements for NEBS 7
Power Supply Considerations 7
Power Connection Guidelines 7
Guidelines for DC-Powered Systems 8
Guidelines for AC-Powered Systems 8
Prevent Power Loss 8
Preventing ESD Damage 9
Cisco 8011-2X2XP4L PLE Service Endpoint Router Overview 11
CHAPTER 2
Temperature and Physical Specification 12
Cisco 8011-2X2XP4L PLE Service Endpoint Router Features 12
Network Interfaces 12
Interface Naming 13
USB Console 13
Online Insertion and Removal 13
Supported Transceiver Modules 14
Prepare for Installation 15
CHAPTER 3
General Precautions 15
Site Planning Checklist 16
Environmental Requirements 16
Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
iii

Airflow Guidelines 16
Site Power Guidelines 18
Electrical Circuit Requirements 19
Site Cabling Guidelines 19
Asynchronous Terminal Connections 19
Interference Considerations 19
Electromagnetic Interference 20
Radio Frequency Interference 20
Lightning and AC Power Fault Interference 20
Tools and Equipment 20
Prepare Your Location 21
Prepare Yourself 21
Prepare Rack for Router Installation 22
Cabinet Selection Guidelines 22
Unpack the Cisco 8011 Router 23
Install the Device 27
CHAPTER 4
Rack Mounting the Router 27
Rack Mounting Brackets 30
Mounting the Router on the Rack 31
Wall Mount 36
Ground the Device 38
Install the AC Power Cables 40
Install the DC Power Cables 41
Port Connection Guidelines 43
Connect to the Console Port 43
Connect to the Management Ethernet Port 44
Install and Remove Transceiver Module 45
Safety Precautions for Module Installation and Removal 45
Install and Remove SFP Modules 46
Bale Clasp SFP or SFP+ Module 47
Install a Bale Clasp SFP or SFP+ Module 48
Remove a Bale Clasp SFP or SFP+ Module 49
Connect Interface Ports 51
Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
iv
Contents

Connect a Fiber-Optic Port to the Network 51
Disconnect Optical Ports from the Network 51
Maintain Transceivers and Optical Cables 51
Configure the Device 53
CHAPTER 5
Create the Initial Router Configuration 53
Verify Device Installation 54
Replace Power Supply 57
CHAPTER 6
Remove the DC Power Supply Module 58
Install the DC Power Supply Module 58
Remove the AC Power Supply Module 59
Install the AC Power Supply Module 60
Appendix 61
CHAPTER 7
LEDs 61
Router LEDs 61
Fan Assembly LEDs 63
Power Status LEDs 63
Combination of LEDs 63
SFP and SFP+ Port LEDs 64
Management Port LEDs 64
System Specifications 64
RJ45 Connectors 65
Transceiver and Cable Specifications 66
Console Port Pinouts 66
USB Port Console Pinouts 66
USB Port Memory Pinouts 67
Management Ethernet Port Pinouts 67
Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
v
Contents

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
vi
Contents

CHAPTER 1
Safety Warnings
This handout lists the safety warnings necessary for handling this chassis. Before you install or service the
chassis, review these safety warnings to avoid injuring yourself or damaging the equipment.
For a complete list of translated safety warnings, see the Regulatory Compliance and Safety Information —
Cisco 8000 Series Routers.
The safety warnings are grouped under the following sections:
•Standard Warning Statements, on page 1
•Safety Guidelines for Personal Safety and Equipment Protection, on page 3
•Safety Precautions for Module Installation and Removal, on page 3
•Safety with Electricity, on page 4
•Cautions and Regulatory Compliance Statements for NEBS, on page 7
•Power Supply Considerations, on page 7
•Preventing ESD Damage, on page 9
Standard Warning Statements
Statement 407—Japanese Safety Instruction
You are strongly advised to read the safety instruction before using the product.
https://www.cisco.com/web/JP/techdoc/pldoc/pldoc.html
When installing the product, use the provided or designated connection cables/power cables/AC adapters.
Note
Statement 1003—DC Power Disconnection
To reduce risk of electric shock or personal injury, disconnect DC power before removing or replacing
components or performing upgrades.
Warning
Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
1

Statement 1006—Chassis Warning for Rack-Mounting and Servicing
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to
ensure that the system remains stable. The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the
unit in the rack.
Warning
Statement 1022—Disconnect Device
To reduce the risk of electric shock and fire, a readily accessible disconnect device must be incorporated in
the fixed wiring.
Warning
Statement 1024—Ground Conductor
This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor or
operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable grounding is available.
Warning
Statement 294—Class A Warning for Korea
This is a Class A device and is registered for electromagnetic compatibility (EMC) requirements for industrial
use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be
replaced with a residential-use type.
Warning
Statement 1049—Rack Installation
To reduce the risk of bodily injury, mount the chassis on a rack that is permanently affixed to the building.
Warning
Statement 9001—Product Disposal
Ultimate disposal of this product should be handled according to all national laws and regulations.
Warning
Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
2
Safety Warnings
Standard Warning Statements

Statement 1017—Restricted Area
This unit is intended for installation in restricted access areas. Only skilled, instructed, or qualified personnel
can access a restricted access area.
Warning
Statement 1071—Warning Definition
IMPORTANT SAFETY INSTRUCTIONS
Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Read the installation instructions before using, installing, or
connecting the system to the power source. Use the statement number at the beginning of each warning
statement to locate its translation in the translated safety warnings for this device.
SAVE THESE INSTRUCTIONS
Warning
Safety Guidelines for Personal Safety and Equipment Protection
The following guidelines ensure your safety and protect the equipment. This list does not include all the
potentially hazardous situations. Therefore, you must be alert.
• Before moving the system, always disconnect all power cords and interface cables.
• Never assume that power is disconnected from a circuit; always check.
• Before and after installation, keep the chassis area clean and dust free.
• Keep tools and assembly components away from walk areas where you or others can trip over them.
• Do not work alone if potentially hazardous conditions exist.
• Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
• Do not wear loose clothing that may get caught in the chassis.
• When working under conditions that may be hazardous to your eyes, wear safety glasses.
Safety Precautions for Module Installation and Removal
Be sure to observe the following safety precautions when you work on the chassis.
Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
3
Safety Warnings
Safety Guidelines for Personal Safety and Equipment Protection

Statement 1006—Chassis Warning for Rack-Mounting and Servicing
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to
ensure that the system remains stable. The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the
unit in the rack.
Warning
Statement 1008—Class 1 Laser Product
This product is a Class 1 laser product.
Warning
Statement 1089—Instructed and Skilled Person Definitions
An instructed person is someone who has been instructed and trained by a skilled person and takes the necessary
precautions when working with equipment.
A skilled person or qualified personnel is someone who has training or experience in the equipment technology
and understands potential hazards when working with equipment.
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Statement 1090—Installation by Skilled Person
Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089 for
the definition of a skilled person.
There are no serviceable parts inside. To avoid risk of electric shock, do not open.
Warning
Safety with Electricity
Statement 1003—DC Power Disconnection
To reduce risk of electric shock or personal injury, disconnect DC power before removing or replacing
components or performing upgrades.
Warning
Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router
4
Safety Warnings
Safety with Electricity