Cisco CATALYST RPS 2300 Quick start guide

Corporate Headquarters:
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Installation Notes for Catalyst 3750-E,
Catalyst 3560-E Switches and RPS 2300
Power Supply Modules
This document provides the removal and installation procedures for the power supply modules used with
the Catalyst 3750-E, the Catalyst 3560-E switches, and the Cisco Redundant Power System 2300
(RPS 2300).
For more information about using the power supply modules with a switch or an RPS 2300, see the
Catalyst 3750-E and Catalyst 3560-E Switch Hardware Installation Guide and the Cisco RPS 2300
Hardware Installation Guide on Cisco.com.
For translations of the safety warnings that appear in this publication, see the Regulatory Compliance
and Safety Information for the Catalyst 3750-E and Catalyst 3560-E Switch or the Cisco RPS 2300
Hardware Installation Guide that shipped with the product and that are also available on Cisco.com.
Contents
This document includes these sections:
•Product Overview, page 2
•Power Supply Module Installation, page 5
•Technical Specifications, page 12
•Related Publications, page 14
•Obtaining Documentation, page 14
•Documentation Feedback, page 15
•Cisco Product Security Overview, page 16
•Obtaining Technical Assistance, page 17
•Obtaining Additional Publications and Information, page 18

2
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Product Overview
Product Overview
Table 1 describes the power supply modules.
Table 2 describes the supported power supply modules for the switches and the RPS 2300.
For more information about which RPS 2300 power supply modules to use for specific switch support,
see the Cisco Redundant Power System 2300 Hardware Installation Guide.
The 750-W and 265-W AC power supply modules are autoranging units that support input voltages
between 100 and 240 VAC. The 1150-W power supply module is an autoranging unit that supports input
voltages between 115 and 240 VAC. The DC power supply module has dual input feeds (A and B) and
supports input voltages between 36 and 72 VDC.
The AC power supply modules include a power cord for connection to an AC power outlet. The 1150-W
and 750-W modules use a 16-AWG cord (only North America). All other modules use an 18-AWG cord.
The DC power supply module requires wiring to a DC-power source.
Table 1 Power Supply Module Part Numbers and Description
Part number Description
C3K-PWR-1150WAC 1150-W AC power supply module
C3K-PWR-750WAC 750-W AC power supply module
C3K-PWR-265WAC 265-W AC power supply module
C3K-PWR-265WDC 265-W DC power supply module
Table 2 Power Supply Modules Used with Switches and RPS 2300
Catalyst 3750-E and
Catalyst 3560-E
Switches and RPS 2300
1150 W AC
Power Supply
750 W AC
Power Supply
265 W AC
Power Supply
265 W DC
Power Supply
48-port PoE switch1
1. For full 15.4-W support on a 48-port PoE switch, you must use the 1150-W AC power supply module in the switch.
Primary or spare Spare or primary Not allowed Not allowed
24-port PoE switch Spare or primary Primary or spare Not allowed Not allowed
48-port non-PoE
switch
Spare Spare Primary or spare Primary or spare
24-port non-PoE
switch
Spare Spare Primary or spare Primary or spare
RPS 23002
2. If only one power supply module is installed in the RPS 2300, you must install the blank insert in the empty power supply
slot.
Primary Primary Not allowed Not allowed

3
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Product Overview
Figure 1 to Figure 3 show the power supply modules.
Figure 1 1150-W AC Power Supply Module
Figure 2 750-W AC and 265-W AC Power Supply Modules
11150-W AC power supply module 5AC power connector
2AC OK LED 6Cooling fans
3PS OK LED 7Extraction handle
4Captive screw
200058
AC OK PS OK
1
45667
32
1750- or 265-W AC power supply module 4Captive screws
2AC OK LED 5AC power connector
3PS OK LED 6Extraction handle
200057
AC OK PS OK
100-240 V
10-5 A
50-60 HZ
1
4
4
5
6
32

4
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Product Overview
Figure 3 265-W DC Power Supply Module
The power supply modules have two status LEDs. Table 3 lists the LED colors and their meanings.
1265-W DC power supply module 4Captive screws
2Input power terminals 5Extraction handle
3DC OK and PS OK LEDs
FRU CC 265W
DC IN
PS OK
A
+
A
+
INPUT
-36 to -72V
/12A
OUTPUT
265W MAX
/22A
200059
1
4
4
5
32
Table 3 Power Supply Module LEDs
AC-Power Supply Module LEDs
AC OK Description PS OK Description
Off No AC input power Off Power supply failure
Green AC input power present Green Power output to switch active
Red No output power to switch
DC-Power Supply Module LEDs
DC IN Description PS OK Description
Off No DC input power Off Power supply failure
Green DC input power present Green Power output to switch active

5
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Power Supply Module Installation
Power Supply Module Installation
This section describes how to remove and install a new or replacement power supply module in
Catalyst 3750-E and Catalyst 3560-E switches, or an RPS 2300. See these sections:
•Tools and Equipment, page 5
•Installation Guidelines, page 5
•Installing an AC-Power Supply, page 6
•Installing a DC-Power Supply (Only Catalyst 3750-E and 3560-E Switches), page 8
Tools and Equipment
Obtain these necessary tools and equipment:
•Ratcheting torque screwdriver with a number-2 Phillips head that exerts up to 15 pound-force inches
(lbf-in.) or 240 ounce-force inches (ozf-in.) of pressure. For 1150-W power supply modules, the
screwdriver shaft length should be at least 6-inches long.
•Power-supply power-cord retainer in the switch accessory kit.
Installation Guidelines
Observe these guidelines when removing or installing a power supply module:
•Do not force the power supply module into the slot. This can damage the pins on the switch or the
RPS 2300 if they are not aligned with the unit.
•A power supply module that is only partially connected to the switch or the RPS 2300 can disrupt
the system operation.
•Remove power from the power supply module before removing or installing the module.
•The switch supports hot swapping of the power supply when the switch is connected to an RPS 2300
that can provide backup power. You can remove and replace the power supply without interrupting
normal switch operation. When you insert a new power supply in the switch, there is a 5-second
delay while the switch software polls the device. The switch power supply then automatically
provides power, and the RPS is available to power other devices.
•The RPS 2300 supports hot swapping of the power supply module when an external device is
connected to it.
– If the RPS 2300 is not backing up an external device, you can remove and replace the power
supply module without disconnecting the system power.
– If two 1150-W power supply modules are installed in the RPS 2300, you can remove one of the
modules when backing up an external device.
– The RPS 2300 does not support hot swapping of the power supply module when two 750-W
power supply modules are installed and the RPS 2300 is backing up a device with an 1150-W
power supply.
•Make sure that you tighten the power supply module captive screws before moving the switch or the
RPS 2300.
•When replacing the 1150-W or the 750-W power supply module, verify that you are using the
correct power cord (CAB-16AWG-AC, only North America).

6
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Power Supply Module Installation
Warning Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed
circuitry could constitute an energy hazard. Statement 206
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Installing an AC-Power Supply
To remove and install an AC-powered power supply module, follow these steps:
Step 1 Turn off the power at its source.
Step 2 Detach the power cord retainer from the power cord.
Step 3 Remove the power cord from the power connector.
Step 4 Use a Phillips screwdriver to loosen the two captive screws at the lower edge that secure the power
supply to the chassis.
Caution Do not leave the power supply slot open for more than 90 seconds while the switch or the RPS 2300 is
operational.
Step 5 Remove the power supply module from the power slot by pulling on the extraction handle.
Step 6 Insert the new power supply into the power supply slot, and gently push it into the slot (Figure 4 and
Figure 5). When correctly inserted, the power supply is flush with the panel. Note: the 1150-W power
supply module extends 3.6 inches (9.14 cm) from the panel.
Figure 4 Inserting an AC-Power Supply into a Switch
158122
AC OK PS OK
100-240 V
10-5 A
50-60 HZ

7
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Power Supply Module Installation
Figure 5 Inserting an AC-Power Supply into an RPS 2300
Step 7 Align the two captive screws with the screw holes in the panel. Using a ratcheting torque screwdriver,
torque each screw to 10 lbf-in. (160 ozf-in.).
Step 8 Connect the power cord to the power supply and to an AC-power outlet.
Step 9 (Optional) Snap the AC power cord retainer into place to secure the power cord (Figure 6 and Figure 7).
Figure 6 AC-Power Supply and Power Cord Retainer Installed in a Switch
Figure 7 AC-Power Supply and Power Cord Retainer Installed in the RPS 2300
Step 10 Turn on the power at the power source.
Step 11 Confirm that the power supply AC OK LED is green. See Table 3 for a description of the module LEDs.
Cisco RPS 2450
STDBY /
ACTIVE
1
TEMP
FAN
234
DC OUTPUT
SELECT STDBY/
ACTIVE
56
AC OK DC OK
100-240V
10-5 A
50-60HZ
ACOKDCOK
100-240 V
10-5 A
50-60 HZ
100-240V
10-5 A
50-60 HZ
100-240 V
10-5 A
50-60 HZ
157544
157706
AC OK PS OK
100-240 V
10-5 A
50-60 HZ
STDBY/
ACTIVE
56
Redundant Power System 2300
AC OK DC OK
100-240 V
10-5 A
50-60 HZ
200107

8
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Power Supply Module Installation
Installing a DC-Power Supply (Only Catalyst 3750-E and 3560-E Switches)
To connect the switch to a DC-input power source, follow these steps:
1. Preparing for Installation, page 8
2. Grounding the Switch, page 9
3. Installing the DC Power Supply in the Switch, page 10
4. Wiring the DC-Input Power Source, page 11
Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure
that no exposed portion of the DC-input power source wire extends from the terminal block plug.
Statement 122
Warning Before connecting or disconnecting ground or power wires to the chassis, ensure that power is
removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel
board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch
handle of the circuit breaker in the OFF position. Use a voltmeter to test for 0 (zero) voltage at the
power terminals on the chassis. Statement 196
Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 15 A. Statement 1005
Note The grounding architecture of this product is DC-isolated (DC-I).
Preparing for Installation
Obtain these necessary tools and equipment:
•Ratcheting torque screwdriver with a number-2 and a number-1 Phillips head that exerts up to
15 pound-force inches (lbf-in.) or 240 ounce-force inches (ozf-in.) of pressure.
•Panduit crimping tool with optional controlled-cycle mechanism (model CT-720, CT-920,
CT-920CH, CT-930, or CT-940CH).
•Wire-stripping tools.
•12-gauge copper ground wire (insulated or noninsulated) when using the single-ground connection.
•6-gauge copper ground wire (insulated or noninsulated) when using the dual-ground connection.
•Ground lug screw and lug ring in the switch accessory kit. For a dual ground connection, also use
the dual-ground adaptor and dual-hole lug from the DC power supply accessory kit.
•Four leads of 16-gauge copper wire.
•Four round eyelet terminals or four fork-type terminals from the DC power supply accessory kit.

9
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Power Supply Module Installation
Grounding the Switch
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning When installing or replacing the unit, the ground connection must always be made first and
disconnected last. Statement 1046
Caution To make sure that the equipment is reliably connected to earth ground, follow the grounding procedure
instructions.
Follow these steps to install either a single-ground lug or a dual-ground lug on the switch. Make sure to
follow any grounding requirements at your site.
Step 1 Locate the ground lug screw and the lug ring in the switch accessory kit. For a dual-ground connection,
also locate the dual-ground adaptor and the dual-hole lug that ships with the DC power supply module.
Step 2 If your ground wire is insulated, use a wire stripping tool to strip the 12-gauge or 6-gauge ground wire
to 0.5 inch (12.7 mm) ± 0.02 inch (0.5 mm). Use 12-gauge copper ground wire for the single-ground
connection. Use 6-gauge copper ground wire for the dual-ground connection.
Figure 8 Stripping the Ground Wire
Step 3 Slide the open end of the ground lug over the exposed area of the wire.
Step 4 Using a Panduit crimping tool, crimp the ground lug to the wire.
Figure 9 Crimping the Ground Lug
Insulation Wire lead
0.5 in. (12.7 mm) ± 0.02 in. (0.5 mm)
60528
200044

10
Installation Notes for Catalyst 3750-E, Catalyst 3560-E Switches and RPS 2300 Power Supply Modules
78-17570-01
Power Supply Module Installation
Step 5 Use the ground screw to attach the single-ground lug and wire assembly or the dual-ground adaptor to
the switch rear panel. Using a ratcheting torque screwdriver, torque the ground-lug screw to 60 lbf-in.
(960 ozf-in.) (Figure 10).
Step 6 For a dual-ground adaptor, attach the dual-hole lug and wire assembly to the adaptor with the supplied
nuts (Figure 10).
Figure 10 Attaching the Ground Lug and Wire Assembly
Step 7 Connect the other end of the grounding wire to an appropriate grounding point at your site or to the rack.
Installing the DC Power Supply in the Switch
To remove and install a DC-powered power supply module, follow these steps:
Step 1 Turn off power at the DC circuits. To ensure that power is removed from the DC circuits, locate the
circuit breakers for the DC circuits, switch the circuit breakers to the OFF position, and tape the
circuit-breaker switches in the OFF position.
Step 2 Use a number-2 Phillips screwdriver to remove the plastic safety cover from the power supply terminal
blocks.
Step 3 Use a number-1 Phillips screwdriver to remove the DC-input power wires from the power terminals.
1Single-ground screw and lug ring
2Dual-ground adaptor and dual-hole lug
FR
F
157547
1
2