Cisco NCS 2000 series User manual

Installing the Cisco NCS 2000 Series Passive
Optical Modules
Last Modified: 2019-02-22
Installing the Cisco NCS 2000 Series Passive Optical Modules
Introduction
This document explains how to install and operate the Cisco NCS 2000 Series passive optical modules, the
fiber shuffle, and the MPO fan-out unit. The Cisco NCS 2000 Series encompasses platforms from Cisco NCS
2002 onwards.
The passive optical modules are used to build the optical network system. The fiber shuffle and MPO fan-out
unit mechanically holds 14 and 10 passive optical modules respectively, thus enabling interconnection of flex
spectrum ROADM nodes that contain 16-WXC or SMR-FS cards.
The passive optical modules, fiber shuffle, and MPO fan-out unit can be installed on:
• 19-inch (482.6 mm) or 23-inch (584.2 mm) EIA standard racks
• 19-inch (482.6 mm) IEC rack
• 600 mm x 600 mm or 600 mm x 300 mm ETSI rack
The following table lists the PIDs of the fiber shuffle and MPO fan-out unit:
Table 1: PIDs of the Fiber Shuffle and MPO Fan-out Unit
DescriptionModule
The MF-6RU unit is referred to as the fiber shuffle.
A combination of 14 single-slot NCS2K-MF-DEG-5
(NCS2K-MF-DEG-5-CV) and NCS2K-MF-UPG-4
(NCS2K-MF-UPG-4-CV) passive optical modules
can be installed in this unit. It is also possible to install
a combination of 14 single-slot
NCS2K-MF-2MPO-ADP, NCS2K-MF-4x4-COFS,
NCS2K-MF-MPO-8LC, and NCS2K-MF-6AD-CFS
passive optical modules.
NCS2K-MF-6RU= (MF-6RU)
Installing the Cisco NCS 2000 Series Passive Optical Modules
1

DescriptionModule
The MF10-6RU unit is referred to as the MPO fan-out
unit.
A combination of 10 double-slot
NCS2K-MF-10AD-CFS, NCS2K-MF-16AD-CFS,
NCS2K-MF-16AE-CFS, NCS2K-MF-MPO-16LC
(NCS2K-MF-M16LC-CV), NCS2K-MF-MPO-20LC,
and NCS2K-MF-8X10G-FO units can be installed in
this unit.
NCS2K-MF10-6RU= (MF10-6RU)
Blank unit for the MF-6RU unit.NCS2K-MF-1SL-CVR=
Blank unit for the MF-10-6RU unit.NCS2K-MF-2SL-CVR=
USB cable; two meters longNCS2K-USB3-CBL-2=
USB cable; three meters longNCS2K-USB3-CBL-3=
Plastic transparent cover for the MF-6RU and
MF-10-6RU unit.
NCS2K-MF-6RU-CVR=
All passive optical modules, (except the mesh patch panel module), are installed using the rack mounting
bracket that is one rack unit (RU) high and can be directly connected to the NCS 2015 ECU. The passive
optical modules can also be installed in the fiber shuffle or MPO fan-out unit.
The following table lists the passive optical modules:
DescriptionModule
16-channel colorless omni-directional add/dropNCS2K-MF-16AD-CFS=
4-channel colorless omni-directional add/dropNCS2K-MF-4X4-COFS=
MPO to 8-LC adapterNCS2K-MF-MPO-8LC=
5-degree mesh moduleNCS2K-MF-DEG-5=
4-degree upgrade moduleNCS2K-MF-UPG-4=
MPO-16 to 16-LC fan-out moduleNCS2K-MF-MPO-16LC=
Double MPO-16 to two MPO-8 adapter moduleNCS2K-MF-2MPO-ADP=
16-port add/drop module with express capabilityNCS2K-MF-16AE-CFS=
10-port add/drop moduleNCS2K-MF-10AD-CFS=
8-degree mesh patch panel with 5 add/drop portsNCS2K-PPMESH8-5AD=
5-degree mesh connection verification module with
MPO-8 loopback caps (NCS2K-MPO-LBK=)
NCS2K-MF-DEG-5-CV=
4-degree upgrade connection verification module with
MPO-8 loopback caps (NCS2K-MPO-LBK=)
NCS2K-MF-UPG-4-CV=
Installing the Cisco NCS 2000 Series Passive Optical Modules
2
Installing the Cisco NCS 2000 Series Passive Optical Modules
Introduction

DescriptionModule
MPO-16 to 16-LC fan-out connection verification
module with LC loopback caps (NCS2K-LC-LBK=)
NCS2K-MF-M16LC-CV=
MPO-24 to 20-LC fan-out moduleNCS2K-MF-MPO-20LC
Splitter/coupler module with six ports used as
colorless or gridless add/drop units in NCS2K
ROADM configurations.
NCS2K-MF-6AD-CFS=
MPO to LC fan-out module used as client
interconnection for the NCS2K and NCS4K line cards
using QSFP+ ports.
NCS2K-MF-8X10G-FO=
• All modules can be used to accommodate the ROADM nodes built with the SMR-FS and AD-FS cards.
• A set of photodiodes are included on selected ports of each module for optical power monitoring.
•USB communication channel can be used to retrieve the optical power levels monitored by the photodiodes
and the inventory and insertion loss (IL) data of the optical paths stored in the modules. The USB channel
can also be used to activate electrical actuators or LEDs present on the front panel of the module.
• The xx SMR9 FS, SMR20 FS, or SMR20 FS CV and the 12-AD-FS or 16-AD-FS cards can be
interconnected by the NCS2K-MF-UPG-4=, NCS2K-MF-UPG-4-CV=, NCS2K-MF-DEG-5=,
NCS2K-MF-DEG-5-CV=, NCS2K-MF-MPO-16LC=, NCS2K-MF-M16LC-CV=,
NCS2K-MF-2MPO-ADP=, or the NCS2K-PPMESH8-5AD= module.
• The NCS2K-MF-16AE-CFS= and the NCS2K-MF-10AD-CFS= modules are only used as a passive
add/drop modules in the Not-DWDM networks.
The following table lists the MPO cables that can be used with the passive modules from Release 10.6.1:
DescriptionMPO Cables
Fan-out cable with one MPO-24 connector on one
side and 16 LC connectors on the other side.
The cable is two meters long and can be used in
ROADM configurations with the
NCS2K-MF-6AD-CFS module. This cable can also
be used as a fan-out cable to connect the LC interface
directly to the SMR20 FS MPO ports.
ONS-MPO-16LC-2
Multi-fiber patch cord with MPO-12 connectors. The
12 fibers have straight connections. There are four
variants: two, four, six, and eight meters.
• ONS-12MPO-MPO-2=
• ONS-12MPO-MPO-4=
• ONS-12MPO-MPO-6=
• ONS-12MPO-MPO-8=
The cables can interconnect the QSFP+ client ports
of NCS2K-400G-2C2 and NCS4K-4H-OPW-QC2
with the NCS2K-MF-8X10G-FO passive module.
ONS-12MPO-MPO-x
Installing the Cisco NCS 2000 Series Passive Optical Modules
3
Installing the Cisco NCS 2000 Series Passive Optical Modules
Introduction

DescriptionMPO Cables
Multi-fiber patch cord with MPO-12 connectors. The
12 fibers have crossed fiber interconnections. There
are four variants: two, four, six, and eight meters.
• ONS-12MPO-XMPO-2=
• ONS-12MPO-XMPO-4=
• ONS-12MPO-XMPO-6=
• ONS-12MPO-XMPO-8=
The cable is used to interconnect the
NCS2K-MF-DEG-5-CV and the
NCS2K-MF-UPG-4-CV passive modules with the
NCS2K-MF-MPO-8LC adapter.
ONS-12MPO-XMPO-x
Multi-fiber patch cord with MPO-24 connectors that
has only 16 fibers connected. Fibers 1, 2, 11, 12, 13,
14, 23, and 24 are not connected. There are four
variants: two, four, six, and eight meters.
• ONS-16MPO-MPO-2=
• ONS-16MPO-MPO-4=
• ONS-16MPO-MPO-6=
• ONS-16MPO-MPO-8=
The cable is used for interconnections inside the
ROADM with MPO-24 standard. The patch cord can
be used for interconnections between SMR20 FS and
NCS2K-MF-M16LC-CV, or NCS2K-MF-2MPO-ADP
or NCS2K-PPMESH8-5AD. The patch cord can also
be used for interconnections between
NCS2K-16-AD-CCOFS and
NCS2K-MF-M16LC-CV.
ONS-16MPO-MPO-x
Safety Information
Before you install, operate, or service the passive optical modules, you must read the Regulatory Compliance
and Safety Information for Cisco NCS 2000 Series document for important safety information and warning
translations.
The passive optical modules are compliant with the GR 1089, UL60950 /CSA 22.2 No. 60950-00, and IEC
60950 standards.
Laser Radiation Emission Restrictions
The Class 1M Laser safety and warning label affixed to the passive optical modules indicate that the product
should never be used or installed in an optical network with emissions higher than Class 1M.
Class 1M laser radiation when open. Do not view directly with optical instruments. Statement 281
Warning
Installing the Cisco NCS 2000 Series Passive Optical Modules
4
Installing the Cisco NCS 2000 Series Passive Optical Modules
Safety Information

Laser Safety During Operation
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or
view directly with optical instruments. Statement 1051
Warning
Electrical Safety
The passive optical modules are optically and electrically passive and require no electrical connections. No
electrostatic discharge (ESD) or other electrical safety considerations apply.
Fiber Shuffle
The MF-6RU unit is six RU high and can be used to interface 14 single slot passive optical modules with the
NCS 2015 ECU. It contains a USB 3.0 hub that consolidates all USB 2.0 connections between the passive
optical modules units and the NCS 2015 ECU using a single USB cable. It allows connections between line
cards and optical passive modules units using simple cabling. The slots are covered by blank units. The
MF-6RU unit is shipped with USB connectors connected to the corresponding blank units. A plastic transparent
door can be installed in front of the unit for fiber and cable management. Mounting brackets are shipped with
the unit.
Figure 1: NCS2K-MF-6RU Unit
Cable guide2Blank unit1
USB connector3
Installing the Cisco NCS 2000 Series Passive Optical Modules
5
Installing the Cisco NCS 2000 Series Passive Optical Modules
Laser Safety During Operation

MPO Fan-out Unit
The MF10-6RU unit is six RU high and can be used to interface 10 double slot passive optical modules with
the NCS 2015 ECU. It contains a USB 3.0 hub that consolidates all USB 2.0 connections between the passive
optical modules units and the NCS 2015 ECU using a single USB cable. It allows connections between line
cards and optical passive modules units using simple cabling. It also has an additional USB 3.0 port on its
faceplate that allows it to be connected to only one MF10-6RU unit.
The slots are covered by blank units and USB connectors are connected to the corresponding blank units. A
plastic transparent door can be installed in front of the unit for fiber and cable management. Mounting brackets
are shipped with the unit.
Figure 2: NCS2K-MF10-6RU Unit
Cable guide2Blank unit1
USB connector3
This procedure describes the steps to install the MF-6RU or MF10-6RU unit on the ANSI or ETSI equipment
rack.
Procedure
Step 1 For a 23-inch ANSI or 21-inch ETSI rack installation, mount the four brackets on the MF-6RU unit or
MF10-6RU unit and:
a) Place the mounting bracket flush against the MF-6RU or MF-0-6RU unit.
b) Align the mounting bracket screw holes against the MF-6RU or MF10-6RU unit screw holes.
c) Insert the M6 screws and tighten them.
d) Repeat steps 1a through 1c to mount the remaining three brackets on the unit.
Installing the Cisco NCS 2000 Series Passive Optical Modules
6
Installing the Cisco NCS 2000 Series Passive Optical Modules
MPO Fan-out Unit

Figure 3: Mounting Brackets on the MF-6RU Unit for a 23-inch ANSI Rack Installation
Washer223-inch ANSI rack
mounting bracket
1
Screw3
Installing the Cisco NCS 2000 Series Passive Optical Modules
7
Installing the Cisco NCS 2000 Series Passive Optical Modules
MPO Fan-out Unit

Figure 4: Mounting Brackets on the MF-6RU Unit for a 21-inch ETSI Rack Installation
Washer2Z shaped 21-inch ETSI
rack mounting bracket
1
Screw3
Installing the Cisco NCS 2000 Series Passive Optical Modules
8
Installing the Cisco NCS 2000 Series Passive Optical Modules
MPO Fan-out Unit

Figure 5: Mounting Brackets on the MF10-6RU Unit for a 23-inch ANSI Rack Installation
Washer223-inch ANSI rack
mounting bracket
1
Screw3
Installing the Cisco NCS 2000 Series Passive Optical Modules
9
Installing the Cisco NCS 2000 Series Passive Optical Modules
MPO Fan-out Unit

Figure 6: Mounting Brackets on the MF10-6RU Unit for a 21-inch ETSI Rack Installation
Washer2Z shaped 21-inch ETSI
rack mounting bracket
1
Screw3
Step 2 Install the MF-6RU or MF10-6RU unit on the appropriate rack equipment:
a) Lift the MF-6RU or MF10-6RU unit to the desired position in the rack.
b) Align the screw holes on the mounting brackets with the mounting holes in the rack.
For a 19-inch ANSI rack installation, external mounting brackets are not installed on the MF-6RU
or MF10-6RU unit. The unit is mounted directly on the equipment rack using screws and washers.
Note
c) Insert the screws and tighten them.
Installing the Cisco NCS 2000 Series Passive Optical Modules
10
Installing the Cisco NCS 2000 Series Passive Optical Modules
MPO Fan-out Unit