Cisco SCE8000 GBE User manual

QUICK START GUIDE
Cisco SCE8000 10 GBE QUICK START GUIDE
1Preparing for Installation
2Rack-Mounting the SCE8000 Chassis
3Connecting Power Supply Units
4Connecting Management Interfaces and Performing Initial System Configuration
5Cabling Line Ports
6Completing the Installation
7Troubleshooting
8Obtaining Documentation and Submitting a Service Request

2
Revised: December, 2008, Release 3.1.7, OL-16595-02
1 Preparing for Installation
This section contains warnings, tools and part information, and site preparation details.
Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any
equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for
preventing accidents.
Warning Only trained and qualified personnel should install, replace, or service this equipment.
Warning Read the installation instructions before you connect the system to its power source.
Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only
be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is
controlled by the authority responsible for the location.
Warning Voltage is present on the backplane when the system is operating. To reduce risk of an electric shock, keep hands
and fingers out of the power supply bays and backplane areas.
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Warning Before you begin the installation of the SCE8000, read the Regulatory Compliance and Safety Information for the
Cisco SCE8000 Platform document.
Site Preparation
•Verify that the power service at the site is suitable for the SCE8000 chassis.
•Print out and have accessible the Site Planning Checklist and the Cisco SCE8000 Installation Checklist from the Cisco
SCE8000 Installation and Configuration Guide to record information about this installation.
Tools and Parts
Use the following list of tools and parts as a checklist for preparing to install the SCE 8000 chassis:
•Number 1 and number 2 Phillips screwdrivers
•3/16-inch flat-blade screwdriver
•Tape measure and level
•Masking tape or some other method of marking the desired installation height in the rack
•One grounding lug
•Two M4 (metric) hex-head screws with locking washers

3
Note The grounding lug and M4 hex-head screws with locking washers are provided in kit 69-0815-01
•One grounding wire—Must be sized according to local and national installation requirements. Depending on the power
supply and system, a 12 AWG conductor or larger size wire is required for U.S. installations.
•Crimping tool—Must be large enough to accommodate the girth of the grounding lug when crimping the grounding cable
into the lug.
•Wire-stripping tool
•Appropriate cables to connect the SCE8000 to the network and console terminal
Unpacking the Cisco SCE8000 Chassis
Tip When you unpack the Cisco SCE8000, do not discard the shipping container. Flatten the shipping cartons and store
them with the pallet. You may need these containers if you move or ship the Cisco SCE8000 in the future.
Check the contents of the shipping container:
•Check the contents of the accessories kit against the list of accessories in the Cisco SCE8000 Component List in the Cisco
SCE8000 Installation and Configuration Guide and the packing slip. Verify that you received all listed equipment, which
should include the following:
– Hardware and software documentation, if ordered
– Optional equipment that you ordered, such as network interface cables, transceivers, or special connectors
Check the modules in each slot. Ensure that the configuration matches the packing list and that all the specified interfaces are
included.
2 Rack-Mounting the SCE8000 Chassis
This chapter provides information for rack-mounting the SCE 8000 chassis.
Warning Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information for the
Cisco SCE8000 Platform. This guide contains important safety information you should know before working with
the system.
Note Before you start the installation described in this chapter, see the Site Planning Checklist in the Cisco SCE8000
Installation and Configuration Guide to verify that all site planning activities are complete.
Installation Guidelines
Table 1 lists rack dimensions. Carefully check the contents of the shipping container, the accessories kit, and optional
equipment.
Table 1 Rack Dimensions
Width 17.75 inches (45.09 cm)
Depth •Minimum: 19.25 inches (48.9 cm)
•Maximum 32 inches (81.3 cm)
Minimum vertical clearance 8.7 inches (22.09 cm) (5 RU)

4
Caution If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.
Note We recommend that you maintain a minimum air space of 6 inches (15 cm) between walls and the chassis air vents and
a minimum horizontal separation of 12 inches (30.5 cm) between two chassis to prevent overheating.
The installation hardware is not suitable for use with racks with obstructions (such as a power strip) that could impair access
to field-replaceable units (FRUs).
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure
that the system remains stable. The following guidelines are provided to ensure your safety:
>If it is the only unit in the rack, this unit must be mounted at the bottom of the rack.
>When mounting this unit in a partially-filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
>If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the
rack.
The chassis is shipped with the mounting brackets installed on the front of the chassis. You can remove these brackets and install
them on the rear of the chassis, using the holes provided in the rear side of the chassis (Figure 1).
Figure 1 Cisco SCE 8000 Chassis Brackets
Step 1 Position the chassis in the rack as follows. If the:
•Front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between the mounting posts.
•Rear of the chassis is at the front of the rack, insert the front of the chassis between the mounting posts.
Step 2 Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the equipment rack.
Step 3 Use a tape measure and level to choose and mark the position that the chassis is to be installed in the rack. Make a mark
at equal height on both sides of the rack. This helps ensure that the chassis is installed straight and level (Figure 2).
FAN STATUS
SCM
1
SCM
2
SIP
3
4
SCE8000-FAN
SYSTEMPOWER
OPTICALBYPASS
STATUS
AUX PORT2
LINK
ACTIVE
MASTER
SCE8000 EXTENDED SERVICECONTROLMODULE
OPTICAL
BYPASS
OPTICAL
BYPASS
CONSOLE
10100
1000
LINK
ACTIVE
PORT1
AC
AB
CD
BD
STATUS
CTRL
OPB-SCE8K-MM
OPTICALBYPASS1
TX
RX
TX
RX
TX
RX
TX
RX
AC
AB
CD
BD
STATUS
CTRL
OPB-SCE8K-MM
OPTICAL BYPASS2
TX
RX
TX
RX
TX
RX
TX
RX
SYSTEMPOWER
OPTICALBYPASS
STATUS
AUXPORT2
10100
1000
LINK
ACTIVE
MASTER
SCE8000 EXTENDED SERVICECONTROLMODULE
SCE8000-SCM-E
SCE8000-SCM-E
SCE8000-SIP
CONSOLE
10100
1000
LINK
ACTIVE
PORT1
OPTICAL
BYPASS
OPTICAL
BYPASS
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
10100
1000
270890

5
Figure 2 Installing the Cisco SCE8000 Chassis in the Rack
Step 4 Install the eight (four per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch screws through the holes in the bracket and into
the threaded holes in the equipment rack posts.
Step 5 Use a tape measure and level to verify that the chassis is installed straight and level.
Installing an Optical Bypass Module
Two installation options exist for external bypass modules:
•Chassis mount panel—This panel is mounted on slot #4 of the SCE 8000 chassis. It hosts two optical bypass modules, which
will serve the two traffic links supported by one Cisco SCE 8000 chassis.
•External mounting panel—This panel can be mounted in any 19-inch rack. It hosts up to 4 optical bypass modules, which
serve four traffic links supported by two Cisco SCE 8000 platforms.
Step 1 For external mounting, install the external mounting panel in the 19-inch rack. Screw the mounting panel to the rack
using four 3/4-inch screws, two on each side, through the holes in the mounting panel and into the threaded holes in
the rack posts. For internal mounting, the SCE8000 chassis is shipped with the chassis mounting panel installed in
slot 4.
Step 2 Remove the module filler plate covering the subslot in the mounting panel by loosening the two screws.
Step 3 Carefully insert the optical bypass module into the subslot (no guide rails exist) and tighten the captive screws on either
side of the module (Figure 3).
270891
FAN STATUS
SCM
1
SCM
2
SIP
3
4
SCE8000-FAN
SYSTEMPOWER
OPTICALBYPASS
STATUS
AUX PORT 2
LINK
ACTIVE
MASTER
SCE8000EXTENDEDSERVICECONTROLMODULE
OPTICAL
BYPASS
OPTICAL
BYPASS
CONSOLE
10100
1000
LINK
ACTIVE
PORT 1
A C
A B
C D
B D
STATUS
CTRL
OPB-SCE8K-MM
OPTICAL BYPASS1
TX
RX
TX
RX
TX
RX
TX
RX
AC
AB
CD
BD
STATUS
CTRL
OPB-SCE8K-MM
OPTICAL BYPASS2
TX
RX
TX
RX
TX
RX
TX
RX
SYSTEMPOWER
OPTICALBYPASS
STATUS
AUXPORT2
10100
1000
LINK
ACTIVE
MASTER
SCE8000EXTENDEDSERVICECONTROLMODULE
SCE8000-SCM-E
SCE8000-SCM-E
SCE8000-SIP
CONSOLE
10100
1000
LINK
ACTIVE
PORT 1
OPTICAL
BYPASS
OPTICAL
BYPASS
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
10100
1000

6
Figure 3 Optical Bypass Modules in External Mounting Panel
3 Connecting Power Supply Units
The SCE8000 chassis is shipped with the power supplies (AC or DC) already installed. This section provides information for
grounding the SCE8000 platform and connecting the AC or DC power supply units.
Connecting the Chassis Ground
Note If this equipment is installed in a U.S. or European Central Office, you must connect the system ground on both AC
and DC-powered systems to an earth ground.
Note For DC-powered systems, the system ground is also the power supply ground. The DC ground must be installed with
a permanent connection to an earth ground according to NEC guidelines.
Note When you use the PWR-2700-DC/4 power supply in the Cisco SCE8000 chassis, additional grounding requirements
exist.
Two threaded M4 holes are provided on the chassis frame to attach the ground cable.
270994
FANSTATUS
SCM
1
SCM
2
SIP
3
4
SCE8000-FAN
SYSTEMPOWER
OPTICAL BYPASS
STATUS
AUX PORT2
LINK
ACTIVE
MASTER
SCE8000EXTENDEDSERVICECONTROLMODULE
OPTICAL
BYPASS
OPTICAL
BYPASS
CONSOLE
10100
1000
LINK
ACTIVE
PORT 1
SYSTEMPOWER
OPTICALBYP
ASS
STATUS
AUXPORT2
10 100
1000
LINK
ACTIVE
MASTER
SCE8000EXTENDEDSERVICECONTROLMODULE
SCE8000-SCM-E
SCE8000-SCM-E
SCE8000-SIP
CONSOLE
10100
1000
LINK
ACTIVE
PORT 1
OPTICAL
BYPASS
OPTICAL
BYPASS
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
10100
1000

7
Before you connect system power or turn on the Cisco SCE 8000 chassis, you must complete this procedure:
Step 1 Remove approximately 0.75 inch (19 mm) of the covering from the end of the grounding wire using a wire-stripping
tool.
Step 2 Insert the stripped end of the grounding wire into the open end of the grounding lug.
Step 3 To secure the grounding wire in place in the grounding lug, use the manufacturer recommended crimping tool.
Step 4 Locate and remove the adhesive label from the system grounding pad on the chassis (Figure 4).
Figure 4 Installing the System Ground
Step 5 Place the grounding wire lug against the grounding pad, making sure that solid metal-to-metal contact exists.
Step 6 Secure the grounding lug to the chassis using two M4 screws. Ensure that the grounding lug does not interfere with
other hardware or rack equipment.
Step 7 To ensure adequate earth ground for the Cisco SCE8000 chassis, prepare the other end of the grounding wire, and
connect it to an appropriate grounding point at your site.
Connecting Power
The following sections describe how to reconnect the AC or DC power.
Installing a DC-Input Power Supply
Note The DC return must remain isolated from the system frame and chassis (DC-I).
Warning Before you perform any of the following procedures, ensure that power is removed from the DC circuit.
FAN STATUS
SCM
1
SCM
2
SIP
3
4
SCE8000-FAN
SYSTEM POWER
OPTICAL BYP
ASS
STATUS
AUXPORT2
LINK
ACTIVE
MASTER
SCE8000EXTENDEDSERVICECONTROL MODULE
OPTICAL
BYPASS
OPTICAL
BYPASS
CONSOLE
10100
1000
LINK
ACTIVE
PORT1
AC
AB
C D
B D
STATUS
CTRL
OPB-SCE8K-MM
OPTICAL BYPASS1
TX
RX
TX
RX
TX
RX
TX
RX
AC
AB
CD
BD
STATUS
CTRL
OPB-SCE8K-MM
OPTICAL BYPASS2
TX
RX
TX
RX
TX
RX
TX
RX
SYSTEM POWER
OPTICAL BYP
ASS
STATUS
AUX PORT2
10100
1000
LINK
ACTIVE
MASTER
SCE8000EXTENDEDSERVICECONTROL MODULE
SCE8000-SCM-E
SCE8000-SCM-E
SCE8000-SIP
CONSOLE
10100
1000
LINK
ACTIVE
PORT 1
OPTICAL
BYPASS
OPTICAL
BYPASS
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
STATUS
ACTIVE/LINK
SPA-1X10GE-L-V2
10100
1000
270892
System ground
connector
System ground
connector
Grounding
lug
Wire

8
Note Because the power requirement of the SCE8000 will not exceed 1350 W, it is not necessary to connect two pairs of input
wires to each power supply. If you want to connect two pairs of input wires, both pairs of input wires for one 2700 W
DC-input power supply must come from the same battery system (A feed); and both pairs of input wires for the other
power supply must come from another battery system (B feed).
Note For multiple DC input power supplies, each DC input must be protected by a dedicated circuit breaker or fuse. The
circuit breaker or fuse should be sized according to the power supply input rating and local or national electrical code
requirements.
Step 1 Power supply ground is required. Install the PWR-2700-DC/4 power supply ground as described in this procedure.
Note The system ground connection with the PWR-2700-DC/4 power supply in a Cisco SCE 8000 is provided by the
PWR-2700-DC/4 power supply ground. Additionally, you can connect a system (earth) ground.
Note You must always connect the PWR-2700-DC/4 power supply ground.
Note You must always connect the PWR-2700-DC/4 power supply ground for both power supplies.
Note If you intend to use an additional system (earth ground), ensure that the system ground connection is made. For
ground connection installation instructions, see the “Connecting the Chassis Ground” section on page 6.
Step 2 Remove the plastic bag attached to the front panel and put aside. This bag contains two plastic terminal block barriers,
two cable ties, and two cable holder covers.
Step 3 Verify that power is off to the DC circuit connected to the power supply you are installing. Grasp both power supply
handles (Figure 5.) Slide the power supply into the power supply bay. Make sure that the power supply is fully seated
in the bay.
Figure 5 Handling a DC-Input Power Supply

9
Step 4 Tighten the power supply captive installation screws.
Warning To ensure protective grounding continuity, power supply captive installation screws must be tight.
Note Because the power requirement of the SCE 8000 does not exceed 1350 W, it is not necessary to connect two pairs
of input wires to each power supply. If you want to connect two pairs of input wires, both pairs of input wires for
one 2700 W DC-input power supply must come from the same battery system (A feed); and both pairs of input
wires for the other power supply must come from another battery system (B feed).
Note For multiple DC input power supplies, each DC input must be protected by a dedicated circuit breaker or fuse. The
circuit breaker or fuse should be sized according to the power supply input rating and local or national electrical
code requirements.
Step 5 Remove the four screws securing the terminal block cover, and slide the cover off of the terminal block (Figure 6).
Figure 6 DC-Input Front Panel for 2700 W DC-Input Power Supply
Step 6 Attach the appropriate lugs to the DC-input wires and ground wire. The wires should be sized according to local and
national installation requirements. Use only copper wire. The maximum width of a lug is 0.600 inch (15.2 mm).
Note For North American installations, use fine-stranded copper conductors rated for 90-degrees Celsius.
1Captive installation screw 7Cable holder cover
2DC power cable terminal block 8Cable holder
3Status LEDs 9Tie-wrap
4DC power cable terminal block cover 10 Cable holder
5Cable holder cover 11 Tie-wrap
6Ground
132219
PWR-2700-DC/4
-VE-1
-VE-1
-VE-2
-VE-2
INPUT1
OK
48V-60V
=40A
INPUT2
OK
48V-60V
=40A
FAN
OK
OUTPUT
FAIL
ALL FASTENERS MUST BE FULLY ENGAGED
PRIOR TO OPERATING THE POWER SUPPLY
3
2
6
4
10
1
8
57
11
9

10
Note The power supply terminal block lug opening width is 0.62 inch (15.8 mm). The terminal posts are centered
0.625 inches (15.88 mm) apart and are 1/4-20 threaded. We recommend that you use an appropriately sized
industry standard 2-hole, standard barrel compression lug. The power supply ground studs, located below the
terminal block, are also threaded 1/4-20 and require two 1/4-inch split-ring washers and two 1/4-20 hex nuts.
Step 7 Connect the DC-input wires to the 2700 W power supply terminal block. Depending onto which side you are
connecting the DC-input wires, be sure that the DC-input wires rest in the appropriate cable holder. Figure 7 shows
DC-input wires coming in from the left side.
Connect the DC-input wires to the 2700 W power supply terminal block in this order (Figure 7):
•Ground
•Negative (-)
•Positive (+)
Note When you tighten the terminal nuts, make sure they are snug. Do not overtighten them. Recommended torque
strength is 20 inch-pounds. Over-tightening the terminal nuts can break the terminal block (maximum torque:
36 inch-pounds).
Figure 7 DC-Input Wires on Left Side
When you install the unit, the ground connection must always be made first and disconnected last.
Step 8 Secure the ground cable to the cable holder using the two cable-ties.
Step 9 Retrieve the cable holder covers from the plastic bag and attach to the front panel at the locations (see Figure 6).
Note If the cable holder illustrated as number 5 and 8 in Figure 6 does not hold the DC input cables snugly, use a long
cable tie to secure the cable holders as illustrated in number 9.
Step 10 Secure the terminal block cover using four screws and the terminal block barriers with two screws each.
Step 11 Turn on the DC inputs and verify power supply operation by checking the power supply front panel LEDs.
The power supply rear panel LEDs should be in the following states:
•Input OK LED is green
•Fan OK LED is green
•Output Fail LED is not lit
If the LEDs indicate a power problem, see the “Troubleshooting” section on page 21.
132220
INPUT1
OK
48V-60V
=40A
INPUT2
OK
48V-60V
=40A
FAN
OK
OUTPUT
FAIL
ALL FASTENERS MUST BE FULLY ENGAGED
PRIOR TO OPERATING THE POWER SUPPLY
PWR-2700-DC/4