Cisco ASR 1002 User manual

QUICK START GUIDE
Cisco ASR 1002 Router
1Documentation and Resources
2Prepare for Installation
3Rack-Mount the Router
4Connect the Router to the Network
5Start the System
6Configuring the Router
7After Installation

2
1 Documentation and Resources
Documentation for the Cisco 1000 Series Aggregation Services Routers documentation is online with the exception of the
regulatory compliance and safety documentation and the Cisco 1000 Series Aggregation Services Routers documentation flyer.
For detailed hardware installation instructions, refer to the online Cisco Series 1000 Aggregation Services Routers Hardware
Installation and Initial Configuration Guide. Refer to the following documentation for installation and replacement of parts
(including shared port adapters) and regulatory compliance information:
•Shared port adapter documentation—See the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware
Installation Guide
•Configuration documentation—See the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
Document Revision History
The Document Revision History table below records technical changes to this document.
Documentation Survey
Is Cisco documentation helpful? Click here or go to http://www.cisco.com/warp/public/732/docsurvey/rtg/ to give us your
feedback.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the
monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be
delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS
version 2.0.
Document Version Date Change Summary
OL-15411-03 November 2008 Improved the two-minute window allotted time to replace a power
supply. You now have up to a maximum of five minutes to replace a
power supply.
OL-15411-02 October 2008 General updates
OL-15411-01 July 2008 First version of this document.

3
2 Prepare for Installation
This section contains information about tools and parts, warnings, site preparation information, and information for
rack-mount and equipment shelf or tabletop installation.
Warning Only trained and qualified personnel should install, replace, or service this equipment. Statement 1030
Caution The eUSB panel door on the side of the Cisco ASR 1002 Router must not be opened. If there is a problem with
eUSB flash card, the chassis should be returned.
Before beginning this router installation, read the Regulatory Compliance and Safety Information for the Cisco ASR 1000 Series
Routers document.
Site Preparation and Unpacking
•Lift the router safely out of the packing container.
•Ensure the power service at the site is suitable for the router you are installing.
•Check the packing slip to ensure that all the proper components are present.
•Locate and have accessible the Site Log for recording information about this installation.
Tools and Parts
Use the following list of tools and parts as a checklist for preparing to install the Cisco ASR 1002 Router:
•ESD-preventative wrist strap
•AC power cord
•Appropriate cables to connect the router to the network and to the console terminal
•Tape measure and level (optional)
•Screwdrivers: Number 2 Phillips screwdriver and 3.5 mm or 3/16 inch flat-blade screwdriver
•Two chassis ground lugs and four screws
•The rack-mount and cable-management kit:
– Four 19-inch rack-mount brackets (front and rear rails) and two cable-management brackets
– Three sets of screws: one set for front rack-mount brackets (packaged with several black screws), another set for rear
rack-mount brackets (packaged with several screws), and a set for the cable-management brackets (packaged with four
screws).
Prepare for Equipment Shelf or Tabletop Installation
For an equipment shelf or tabletop installation, verify the following before installing the router:
•The router is off the floor and has adequate ventilation.
•An adequate chassis ground (earth) connection exists for the router.
•The router needs at last 3 inches (7.62 cm) of clearance at the inlet and exhaust vents (front and rear of router).
•The router needs 19 inches (48.26 cm) of clearance at the front and rear to allow for installation or to access cables or
equipment.

4
Prepare for Rack-Mount Installation
Before you begin the rack-mounting tasks:
•Decide whether or not you want to front-mount or rear-mount the chassis.
•Decide whether or not you want to attach cable-management brackets to your chassis.
Note If you install cable-management brackets, make certain that you use the specified rack-mount ear holes as stated
in the procedure and install the brackets after the cassia is mounted in the equipment rack.
•Decide if two-post or four-post rack-mount equipment will be used.
3 Rack-Mount the Router
This section provides information for rack-mounting the router.
Attach the Rack-Mount Brackets—Chassis Front-Mounted
Figure 1 Front Rack-Mount Brackets for the Cisco ASR 1002 Router
To install the rack-mount brackets on a Cisco ASR 1002 Router for a front rack-mount configuration, follow these steps:
Step 1 Locate the threaded holes in the front sides of the chassis.
Step 2 Align the rack-mount bracket to the side of the router. Depending on which set of rack-mount bracket holes you choose
to use to attach the rack-mount bracket to the router, the chassis will either be recessed in the rack or protrude from
the rack.
Step 3 Position the front rack-mount bracket top hole with the chassis first top hole behind the side vent holes as shown in
Figure 1.
Step 4 Insert and tighten the black screws on one side.
Step 5 Repeat Step 1 through Step 4 on the other side of the chassis. Use black screws to secure the rack-mount brackets to
the chassis.
Step 6 To install the cable-management bracket, see “Attach the Cable-Management Bracket” section on page 8.
1Front rack-mount bracket ear and holes 3Front rack-mount bracket screws
2Front rack-mount bracket e
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
STAT
QE0QE1QE2 QE3 BOOTC
ARRIERL
INKPWRSTAT
MTSMGMTAUXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
3
280278
21

5
Attach the Rack-Mount Brackets—Chassis Rear-Mounted
To install the rack-mount on a Cisco ASR 1002 Router for a rear rack-mount configuration, follow these steps:
Step 1 Locate the threaded ear holes in the rear sides of the chassis.
Step 2 Position the rear rack-mount bracket top hole with the chassis from the back (See Figure 2).Make certain that you hold
the rear rack-mount bracket with the ear holes facing outward and towards the rear of the chassis. Align the rack-mount
bracket to the side of the router.
Figure 2 Installing the Cisco ASR 1002 Router Rear Rack-Mount Brackets
Step 3 Insert and tighten the screws.
Step 4 Repeat Step 1 through Step 3 on the other side of the chassis.
This completes the procedure for attaching rear rack-mount brackets to the chassis. Continue to Four-Post Rack Installation,
page 5 or Two-Post Rack Installation, page 7.
Four-Post Rack Installation
Note We recommend that you allow at least 1 or 2 inches (2.54 or 5.08 cm) of vertical clearance between the router and any
equipment directly above and below it.
1Rear rack-mount bracket ear and holes 3Rear rack-mount bracket screws
2Rear rack-mount bracket
280279
2
3
1

6
Figure 3 shows the Cisco ASR 1002 Router in a four-post rack.
Figure 3 Installing the Cisco ASR 1002 Router in a Four-Post Rack - Front and Rear Rack-Mounting
Note Because the rack-mount brackets support the weight of the entire chassis, be sure to use all screws to fasten the two
rack-mount brackets on the chassis to the rack posts.
Note Make certain that you attach the cable-management bracket to the chassis after you install the chassis in an equipment
rack.
To install the chassis in the four-post rack, complete the following steps:
Step 1 Make sure the rack brakes are locked or the rack is stabilized.
Step 2 On the chassis, ensure that all screw fasteners on the installed components are securely tightened.
Step 3 Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that the brakes are engaged or
that the rack is otherwise stabilized.
Step 4 Lift the chassis into position between the rack posts (requires two people).
Step 5 Align the mounting bracket holes with the rack post holes and attach the chassis to the rack. At this point, if there is a
third person, then that person can insert the screws while the other two people hold that chassis in place, unless the
chassis is resting on a shelf).
Step 6 Position the chassis until the rack-mounting ears are flush against the mounting rails on the rack.
Step 7 Insert the bottom screw first and then the second screw at the top of the chassis diagonally from the bottom screw. This
helps secure the chassis in place while you insert the other screws.
1Rear rack equipment rail 3Front rack-mount bracket ear and holes
2Rear rack-mount bracket ear and holes 4Front rack equipment rail
280281
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
4
1
3
2

7
Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the
rack-mount bracket ear holes specified in Step 9.
Step 8 Hold the chassis in position against the mounting rails and follow these steps:
a. Insert the bottom screw into the second ear hole from the bottom of the rack-mount ear and use a hand-held screwdriver
to tighten the screw to the rack rail.
b. Insert the top screw into the second bracket hole from the top of the rack-mount bracket ear hole diagonally from the
bottom screw and tighten the screw to the rack rail. See Figure 3.
c. Repeat these steps for the other side of the chassis.
Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be easily
attached to the rack-mount bracket after the chassis is in the rack.
This completes the procedure for installing the chassis in a four-post rack. Proceed to the “Attach the Cable-Management
Bracket” section on page 8 to continue the installation.
Two-Post Rack Installation
Note Make certain that you attach the cable-management bracket to the chassis after you install the chassis in an equipment
rack.
Note Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches (48.26 cm).
Airflow through the chassis is from front to back.
Figure 4 Installing a Cisco ASR 1002 Router in a Two-Post Rack
1Rack equipment rail 2Rack-mount bracket ear and holes
280282
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
1
2

8
Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and
component damage.
Step 1 Position the chassis so the front is closest to you and lift it carefully into the rack. To prevent injury, avoid any sudden
twists or moves.
Step 2 Slide the chassis into the rack, pushing it back until the rack-mount brackets meet the mounting strips or posts on both
sides of the rack.
Step 3 Position the chassis until the rack-mounting ears are flush against the mounting rails on the rack.
Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the
rack-mount bracket ear holes specified in Step 4.
Step 4 Hold the chassis in position against the mounting rails and follow these steps:
a. The Cisco ASR 1002 Router rack-mount bracket has 4 ear holes and two for the cable-management bracket. Insert the
bottom screw into the fifth hole from the top of the rack-mount ear and use a hand-held screwdriver to tighten the screw
to the rack rail.
b. Insert the top screw into the second hole from the top of the rack-mount bracket ear hole diagonally from the bottom
screw and tighten the screw to the rack rail. See Figure 4.
Step 5 Repeat steps 3 and 4 for the other side of the chassis.
Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be easily
attached to the rack-mount bracket after the chassis is in the rack.
This completes the procedure for installing the chassis in a two-post rack. Proceed to the “Attach the Cable-Management
Bracket” section on page 8 to continue the installation.
Attach the Cable-Management Bracket
The cable-management bracket mount to each rack-mount bracket on the chassis to provide cable-management to both sides of
the chassis.
The cable-management brackets for the Cisco ASR 1002 Router contain one independent cable-management “U” type feature
with two screws for each bracket and provides cable dressing of each card module slots. For the ASR 1000 Series SPA interface,
these brackets work in tandem with shared port adapter product feature cable-management device to allow installation and
removal of adjacent cards without the need to remove cables.
Note Make certain that the cable-management bracket “U” type feature is facing upwards when you attach it to the chassis.
Follow these steps to attach the cable-management brackets to both sides of the Cisco ASR 1002 Router in the rack:
Step 1 Align the cable-management bracket to the rack-mount bracket on one side of the Cisco ASR 1002 Router. The
cable-management bracket aligns to the top hole of the chassis rack-mount bracket.
Step 2 Using a Phillips screwdriver, insert one screw through the cable-management bracket and into the chassis rack-mount
and tighten the screw.
Note Use the package of four screws that came with your Cisco ASR 1002 Router.

9
Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1002 Router
Step 3 Using the bottom rack-mount ear hole, insert the screw through cable-management bracket and into the chassis
rack-mount bracket. Figure 5 shows the cable-management brackets attached to the chassis.
Step 4 Using a Phillips screwdriver and the cable-management screw, thread and tighten the screw to the cable-management
bracket.
Step 5 Repeat Step1 through Step 4 for the other side of the Cisco ASR 1002 Router.
This completes the procedure for installing the cable-management bracket on a Cisco ASR 1002 Router for a chassis rack-mount
configuration.
Chassis Ground Connection Installation
Before you connect power or turn on power to your router, you must provide an adequate chassis ground (earth) connection
for the Cisco ASR 1002 Router. The chassis ground lugs (two) and the respective screws (4) are provided in the accessory kit
that ships with your Cisco ASR 1002 Router.
See Figure 6 for the location of the chassis ground connector on the Cisco ASR 1002 Router.
1Secure the cable-management bottom screw and top screw
to this ear hole
3Front rack-mount bracket
2Cable-management U feature
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
STAT
QE0QE1QE2QE3BOOTCARRIER LINKPWR STAT
MTSMGMTA
UXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
280280
1
1
3
2

10
Figure 6 Cisco ASR 1002 Router Ground Connector Location and eUSB Panel Door
Step 1 Use the wire stripper to strip one end of the AWG #6 wire approximately 0.75 inches (19.05 mm).
Step 2 Insert the AWG #6 wire into the wire receptacle on the grounding lug.
Step 3 Use the manufacturer’s recommended crimping tool to carefully crimp the wire receptacle around the wire; this step is
required to ensure a proper mechanical connection.
Figure 7 Attaching a Ground Lug to the Chassis Ground Connector
Step 4 Attach the grounding lug with the wire on the left to avoid having the grounding wire overlapping the power supply.
1F0 with Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10
Note The Cisco ASR10002 Router does not support
the Cisco ASR1000-ESP20 module.
3The eUSB panel door on the side of the Cisco ASR 1002
Router must not be opened. If there is a problem with
eUSB flash card, the chassis should be returned.
2R0 slot with embedded ASR1000-RP1 and embedded
ASR1000-SIP10
4Cisco ASR 1002 Router ground stud location
1Chassis ground lug 3Chassis ground connector location
2Ground lug screws 4Earth ground symbol
ASR1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
STAT
QE0QE1QE2QE3BOOTCARRIERLINKPWRSTATMTSMGMT AUXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
3
1
2
4
280283
280034
3
4
21

11
Step 5 Locate the chassis ground connector on the side of your chassis.
Step 6 Insert the two screws through the holes in the grounding lug.
Step 7 Use the Number 2 Phillips screwdriver to carefully tighten the screws until the grounding lug is held firmly to the
chassis. Do not overtighten the screws.
Step 8 Connect the opposite end of the grounding wire to the appropriate grounding point at your site to ensure an adequate
chassis ground.
This completes the procedure for attaching a chassis ground connection. Go to the “Connect the Router to the Network” section
on page 11 for information on attaching cables.
4 Connect the Router to the Network
This section provides information about cables and ports and attaching the router to the network.
•Console and Auxiliary Port Cable Connections, page 11
•Management Ethernet Port Cable Connection, page 12
•Connect the Shared Port Adapter Cables, page 13
•Install the Cables Using the Cable-Management Bracket, page 13
Console and Auxiliary Port Cable Connections
This section describes how to attach a cable to the console or auxiliary ports on the Cisco ASR 1002 Router. The Cisco
ASR 1002 Router uses RJ-45 ports for both the auxiliary port and console port to attach a modem or console terminal.
The console DCE-mode port connects a console terminal and a DTE-mode auxiliary port connects a modem or other DCE device
to your router.
Caution Both the console and the auxiliary ports are asynchronous serial ports; any devices connected to these ports must
be capable of asynchronous transmission. (Asynchronous is the most common type of serial device; for example,
most modems are asynchronous devices.) To meet Class A emissions requirements on the Cisco ASR 1002 Router,
shielded cables must be used for the console and auxiliary port connections.
Step 1 Before connecting a terminal to the console port, configure the terminal to match the router console port as follows:
9600 baud, 8 data bits, no parity, 1 stop bits. See Figure 8 for console and auxiliary port connector location.
Step 2 Connect to the port using the RJ-45-to-DB-9 cable.

12
Figure 8 Cisco ASR 1002 Integrated Route Processor Console and Auxiliary Port Connectors
Step 3 After you establish normal router operation, you can disconnect the terminal.
Note For console and auxiliary port pinouts, see Cisco ASR 1002 router specifications in the Cisco ASR 1000 Series
Aggregation Services Routers Hardware Installation and Initial Configuration Guide.
Management Ethernet Port Cable Connection
Caution To comply with Class A emissions requirements, a shielded Ethernet cable must be used.
To use the Management Ethernet interface on the router, perform the following steps:
Step 1 Insert an Ethernet RJ-45 cable into the MGMT ETHERNET port (see Figure 9).
Figure 9 Cisco ASR 1002 Integrated Route Processor Ethernet Management Port Connector
Step 2 Insert the other end of the RJ-45 cable to your management device or network.
1CON—console port 2AUX—auxiliary port
1MGMT port and cable
280285
ASR 1002
stat
pwr
min
maj
crit
0
1
C/A
A/L
0
1
C/A
A/L
STAT
QE0 QE1QE2QE3 BOOTCARRIERLI
NKPWR STATMTSMGMT AUXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
1 2
280286
ASR 1002
stat
pwr
min
maj
crit
0
1
C/A
A/L
0
1
C/A
A/L
STAT
QE0 QE1QE2QE3 BOOTCARRIERLI
NKPWR STATMTSMGMT AUXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
1

13
Step 3 Configure to a fixed speed through the command-line interface (CLI) commands.
Connect the Shared Port Adapter Cables
The instructions for connecting the cables for the shared port adapters installed in the Cisco ASR 1002 Router are contained in
the Cisco ASR 1000 Series Aggregation Services Routers SPA and SIP Hardware Installation Guide.
Install the Cables Using the Cable-Management Bracket
Cables coming off the front side of the Cisco ASR 1002 integrated route processor and SPAs utilize the chassis level
cable-management brackets provided on the chassis rack-mount brackets (see Figure 10).
Figure 10 Cisco ASR 1002 Integrated Route Processor Cable-Management
To secure shared port adapter interface cables and input or output cables connected to the Cisco ASR 1002 Router, follow these
steps:
Step 1 When installing the network interface cables, route the cables up to and through the cable-management bracket ‘U’
device. If you are using very thin cables that slip through the bracket openings, insert nylon cable ties through the holes
in the bracket and wrap them around the cables to secure them.
Step 2 Route the excess cable out through either end of the bracket, coil it, and secure it to the rack using nylon cable ties or
some other mode of attachment.
Step 3 It might be necessary to bundle longer cables to avoid tangling them. Do this at the cable-management bracket or at
the rack, but leave enough slack in the cables to remove a Cisco ASR 1000-ESP5 and change cables as required. Also,
do not block the power supply air vents with cables.
This completes the procedure for installing the cables in the cable-management bracket.
1BITS cable 4AUX cable
2MGMT cable 5Cable-management U feature device
3CON cable
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
STAT
QE0QE1QE2QE3BOOTCARRIERL
INKPWRSTAT
MTSMGMTA
UX CON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
280287
5
5
1 2 3 4

14
Proceed to the “Start the System” section on page 14 to complete the installation.
5 Start the System
Before you start the system, you must connect power to it.
Connect AC Power to the Cisco ASR 1002 Router
This section provides instructions for installing the AC power supply into the Cisco ASR 1002 Router. Read the safety warnings
before you begin.
Warning Never install an AC power module and a DC power module in the same chassis. Statement 1050
Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.
Statement 1046
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if
you are uncertain that suitable grounding is available. Statement 1024
Warning This unit has two power supply connections. All connections must be removed to de-energize the unit. Statement
1028
Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than: AC power supplies 20 A and DC power supplies 30 A for Cisco ASR 1002
Routers. Statement 1005
Figure 11 shows the AC power supply for the Cisco ASR 1002 Router.

15
Figure 11 AC Power Supply for the Cisco ASR 1002 Router
Table 1 describes the AC power supply LEDs on the Cisco ASR 1002 Router.
Table 1 Cisco ASR 1002 Router AC Power Supply LEDs
Note To connect an AC power supply to the Cisco ASR 1002 Router, follow the steps in Installing the AC Power Supply,
page 31.
Connect DC Power to the Cisco ASR 1002 Router
The DC power supply input connector is a euro-style terminal block. A means to provide strain relief to the input wires is
provided on the power supply. The connection order is negative (–), positive (+), and GND.
1Chassis ESD socket 5AC power supply fan
2AC power supply slot number 0 6AC power supply captive installation screw
3AC power supply On (I) /Off (O) switch 7AC power supply slot number 1
4AC power supply LEDs 8AC power inlet
LED Label LED Color Description
INPUT OK Power supply activity Green The AC power supply input voltage is greater than 85V.
None The AC input voltage is less than 70V or the power
supply is turned off.
Flashing For an AC input voltage between 70V and 85V the
INPUT OK LED can be either on, off, or flashing
FAN OK Power supply fan activity
A bi-color LED indicates
fan status.
Green When all fans are operational.
Red When a fan failure is detected.
OUTPUT FAIL Power supply activity Red LED is off to signal that the DC output voltages are
within the normal operating range. Output voltage
between the minimum and maximum limits will not
create an output fail alarm and output voltages below
the minimum or above the maximum will create an
output fail alarm.
OUTPUT INPUT
FAIL OK OK
FAN OUTPUT INPUT
FAIL OK OK
FAN
This unit might have more than
one power supply connection.
All connections must be removed
to de-energize the unit.
This unit might have more than
one power supply connection.
All connections must be removed
to de-energize the unit.
0
1
8 7
280288
41 5 63
2

16
Figure 12 shows the DC power supply for the Cisco ASR 1002 Router.
Figure 12 DC Power Supply for the Cisco ASR 1002 Router
Table 2 describes the DC power supply LEDs on the Cisco ASR 1002 Router.
Table 2 Cisco ASR 1002 Router DC Power Supply LEDs
To connect the DC power supply to a Cisco ASR 1002 Router, follow these steps:
Step 1 At the rear of the router, check that the power switch is in the standby position.
1Chassis ESD socket 6DC power supply captive installation screw
2DC power supply slot 0 label 7DC power supply slot 1 label
3DC power supply switch Standby/On (I) (standby symbol
is a broken circle with a vertical line through the top of it)
8Negative ground lead
4DC power supply LEDs 9Positive ground lead
5Fan 10 Earth ground lead
LED Label LED Color Description
INPUT OK A bi-color LED indicates
presence of input voltage
Green Signals that the DC power supply input voltage is greater
than –43.5VDC at turn-on and remains green down to
–39VDC.
Amber The power supply turns off due to low input voltage
(falls below –39VDC) and indicates that there is still a
voltage present (voltage on the terminal block). The LED
remains amber and is active to around 20V +/-5V. The
LED is not illuminated if the input is below 15V.
FAN OK A bi-color LED indicates
power supply fan status
Green All fans are operational.
Red A fan failure is detected.
OUTPUT FAIL Power supply activity Red It is off signals that the DC output voltage are within the
normal operating range. Output voltage between the
minimum and maximum limits will not create an output
fail alarm, and output voltages below the minimum or
above the maximum will create an Output Fail alarm.
When you turn the power supply on, the red LED
illuminates for two to three seconds to test LED
operation before going off.
280289
OUTPUT INPUT
FAIL OK OK
FAN
-48V/-60V 16A
This unit might have more than
one power supply connection.
All connections must be removed
to de-energize the unit.
OUTPUT INPUT
FAIL OK OK
FAN
-48V/-60V 16A
This unit might have more than
one power supply connection.
All connections must be removed
to de-energize the unit.
9 810
4 5 63
0
1
7
12

17
Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site.
Typically, green or green/yellow is used for ground. Make certain the lead color coding you choose for the DC-input
power supply matches lead color coding used at the DC power source.
Warning When you install the unit, the ground connection must always be made first and disconnected last.
Figure 13 Cisco ASR 1002 Router DC Power Supply
Step 2 Ensure that the negative and positive leads are disconnected from the site power source.
Step 3 Using a wire stripper, strip approximately 0.55 inch (14 mm) from the positive, negative, and ground lead.
Step 4 Insert the stripped end of the ground lead all the way into the ground lead receptacle on the DC-input power supply,
and tighten the receptacle screw using a 3.5mm flat-blade screwdriver to a torque of 0.5 to 0.6Nm.
Step 5 Insert the stripped end of the positive lead all the way into the positive lead receptacle and tighten the receptacle screw
using the same 3.5mm flat-blade screwdriver. Repeat this step for the negative lead.
Step 6 Make sure the entire stripped end of each lead is inserted all the way into its receptacle. If any exposed wire at the
stripped end of a lead is visible after inserting the lead into its receptacle, remove the lead from the receptacle, use the
wire stripper to cut the stripped end of the lead, and repeat Step 3 through Step 5.
Step 7 After tightening the receptacle screw for the ground, positive, and negative DC-input leads, use a cable tie to secure the
three leads to the power supply faceplate.
Step 8 When securing the earth ground, positive, and negative DC-input leads to the power supply faceplate, leave a service
loop in the ground lead to ensure that the ground lead is the last lead to disconnect from the power supply if a great
deal of strain is placed on all three leads as shown in Figure 13.
Caution Leave a service loop in the earth ground lead to ensure that the earth ground lead is the last lead to disconnect from
the power supply if a great deal of strain is placed on all three leads
1Earth ground lead service loop area 3DC power positive lead
2DC power negative lead 4Power supply standby switch
OUTPUT INPUT
FAILOK OK
FAN
-48V/-60V 16A
This unit might havemore than
one power supply connection.
All connections must be removed
to de-energize the unit.
3
1
2
280290
4

18
Step 9 Connect the ground, positive, and negative leads to the power source.
Step 10 Turn the branch source breaker on.
Step 11 Turn the power supply switch to the On (I) position.
Step 12 Verify that the LEDs illuminate.
This completes the procedure for connecting DC-input power.
Verifying Power Supply operation
Follow this procedure to verify power supply is operating correctly.
Step 1 Check that the power supply LEDs are:
•INPUT OK is green
•FAN OK is green
•OUTPUT FAILED is not illuminated
Step 2 To ensure that the power supply state is OK, type the show platform command. This output sample is from a Cisco
ASR1002 router.
MCP_SCAL_R1#sho env all
Chassis type: ASR1002
The following output displays:
If the LEDs indicate a power problem or the power supply state is ps,fail, then contact a customer service representatives for
assistance or additional instructions.
Start the Cisco ASR 1002 Router
After installing your Cisco ASR 1002 Router and connecting cables, start the router as follows.
Check the following conditions before you start the Cisco ASR 1002 Router:
•The Cisco ASR 1002 Router has one slot for FP0 with three subslots for SPAs, subslots 1, 2, and 3. Make certain that each
shared port adapter is firmly seated in its subslot and its captive screws are securely tightened.
•The Cisco ASR1000-ESP5 or ASR1000-ESP10 forwarding processor in the Cisco ASR 1002 router is inserted in slot F0, is
firmly seated in its slot, and its captive screws are securely tightened.
•All network interface cables are connected.
•The console terminal is turned on.
Slot Type State Insert Time
R0 ASR1000-RP1 ok,active 00:03:19
F0 ASR1000-ESP10 ok,active 00:03:19
P0 ASR1002-PWR-AC ok 00:02:50
P1 ASR1002-PWR-AC ps, fail 00:02:50
Slot CPLD Version Firmware Version
R0 08060301 12.2(0:0)
F0 08041102 12.2(33r)XN2

19
Step 1 Turn on power. The green OK LED on the power supply turns on. (Both power supplies are required in the Cisco
ASR 1002 Router.)
Step 2 Listen for the fans; you should immediately hear them operating.
Step 3 During the boot process, observe the system LEDs. The power LED should be green. The STATUS LED lights yellow
to indicate booting and then green when Cisco IOS is running.
Table 3 provides information about the LEDs as the system starts.
Table 3 Cisco ASR 1002 Router LED Activity
LED Label LED Color In the Power Up State -Behavior Description
PWR Power Solid green All power requirements are within specification.
Off The router is in standby mode.
STAT System status Solid green Cisco IOS has successfully booted.
Yellow BOOT ROM has successfully loaded.
Red System failure.
CRIT Critical Solid red Critical alarm indicator. On at power up
MAJ Major Solid red Major alarm indicator.
MIN Minor Amber Minor alarm indicator.
LINK 10/100/1000 RJ-45 Flashing green Link activity indicator.
Off No link.
Solid green Link with no activity.
BOOT eUSB FLASH
BOOT (BootDisk)
Flashing green Activity indicator.
Off No activity.
CARRIER BITS Green In frame and working properly.
Off Out of service or not configured.
Amber Fault or loop condition.
**Built-in
4xGE SPA SFP
Port Status
4 LEDs total, one for each
SFP
Off Port is not enabled.
Amber Port enabled. Problem with the Ethernet link.
Green Port enabled and the Ethernet link is valid.
CC - PWR Embedded SIP power rail
status
Green If all power supplies within their tolerance specifications.
CC - STAT Embedded SIP current status Green Green only when the SPA drivers have started and are
running and all critical processes are running.
Yellow ROMMON is running and during the download and
boot.
Red A fault is detected or the card is powering up.
**The built-in Gigabit Ethernet ports on the Cisco ASR1002 Router support the same small form-factor pluggable (SFP) optical transceivers as the
5x1 GE SPA. For specific shared port adapter SFP compatibility listings, go to Chapter 1 at:
http://cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/install_upgrade/ASR1000/ASRspahw.pdf
Note that the Cisco ASR1002 built-in GE ports support only the SFP-GE-T but not the SFP-GLC-T.

20
Table 4 provides information about the Cisco ASR1000-ESP5 LEDs in the Cisco ASR 1002 Router as the system starts.
Table 4 Cisco ASR1000-ESP5 and ASR1000-ESP10 LED Activity
During the boot process, observe the system LEDs. The STATUS LED comes on immediately as amber, then turns to green when
the Cisco IOS is booted.
Note The system boots differently depending on the configuration that ships with your system. The display below is a
snapshot of messages that are output on the console of the Cisco ASR 1002 Router system after power-up and during
IOS booting. This is only an example of what you might see from any Cisco ASR 1000 Series Router.
Step 4 Observe the initialization process. When the system boot is complete (a few seconds), the Cisco ASR 1002iIntegrated
route processor begins to initialize. The console screen displays a script and system banner similar to the following when
booting flash or harddisk:
asr1002-16-rp0-rommon 2 >boot
bootflash:asr1000rp1-advipservicesk9.v122_33_xn_asr_rls0_throttle_20080114_045627.bin
Located asr1000rp1-advipservicesk9.v122_33_xn_asr_rls0_throttle_20080114_045627.bin
Image size 218869964 inode num 18, bks cnt 53436 blk size 8*512
#########################################################################################################
##############
#########################################################################################################
##############
#########################################################################################################
############
Boot image size = 218869964 (0xd0bb0cc) bytes
Using midplane macaddr
Package header rev 0 structure detected
Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
calculated 9b448f06:3d34317f:54fa04b6:a5d8abae:321bb3f0
expected 9b448f06:3d34317f:54fa04b6:a5d8abae:321bb3f0
Image validated
PPC/IOS XE loader version: 0.0.3
loaded at: 00800000 0D8BD004
zimage at: 00807673 009B8D97
initrd at: 009B9000 01041D66
isord at: 01042000 0D8BA800
avail ram: 00400000 00800000
Kernel load:
Uncompressing image... dst: 00000000 lim: 00400000 start: 00807673 size: 001B1724...done.
Now booting the IOS XE kernel
%IOSXEBOOT-4-BOOT_PARAMETER: (rp/0): Booting with custom BOOT_PARAM setting
%IOSXEBOOT-4-BOOT_PARAMETER: (rp/0): Hardware watchdog timer disabled in ROMMON
LED Label LED Color Behavior Description
PWR Power Solid green All power supplies are within operational limits.
Off The router is in standby mode.
STAT Status Green Code has successfully downloaded and is operational.
Yellow BOOT ROM has successfully loaded.
Red Not booted.
ACTV Active Green The embedded services processor is green when active.
STBY Standby None Will always be off.