Cisco Cisco ASR 5000 Application Detection and Control Administration... Manual

Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]
Cisco 1120 Connected Grid Router
Hardware Installation Guide
Last updated: February 2013
Text Part Number: OL-26438-02

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Cisco and the Cisco logo are trademarks or registered trademarks of Cisco
and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are
the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
No combinations are authorized or intended under this document.
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the
document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Cisco 1120 Connected Grid Router Hardware Installation Guide
©2012 Cisco Systems, Inc. All rights reserved.

iii
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
CONTENTS
CHAPTER 1Unpacking the Router 1-1
Unpacking the Router 1-1
Router Package Contents 1-2
CHAPTER 2Installation Safety and Site Preparation 2-1
Safety Recommendations 2-2
Safety with Electricity 2-3
Preventing Electrostatic Discharge Damage 2-3
General Site Requirements 2-4
Rack Mounting 2-4
Router Environmental Requirements 2-4
Power Guidelines and Requirements 2-4
Network Cabling Specifications 2-5
Preparing for Network Connections 2-5
Ethernet Connections 2-5
Serial Connections 2-5
Required Tools and Equipment for Installation and Maintenance 2-7
CHAPTER 3Router Hardware Description 3-1
Router Overview 3-1
Applications Overview 3-1
Hardware Compliance 3-2
Router Hardware Overview 3-2
Hardware Features 3-4
Chassis 3-4
Mounting Features 3-5
Mounting Procedures 3-6
Module Panel (Front Panel) Features 3-6
Front Panel LEDs 3-7
WiFi Antenna Port 3-7
USB Port 3-8
SD Flash Memory Module 3-8
GPS Antenna Port 3-9
Kensington-Compatible Security Slot 3-9

Contents
iv
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
Connected Grid Module Slots 3-10
Cable Panel (Back Panel) Features 3-11
Back Panel LEDs 3-12
CONFIG Reset Button 3-12
PWR RESET Button 3-12
Small Form-Factor Pluggable (SFP) Ports 3-12
Ethernet Ports 3-13
Combo Ports 3-15
Serial Ports 3-15
Console Port 3-16
AC Power Supply 3-17
DC Input for Battery Backup 3-17
Power Specifications 3-17
Alarm Port 3-18
Internal Hardware Features 3-19
Memory 3-19
Internal GPS Module 3-19
Short-Range Access Point 3-20
Real-Time Clock (RTC) 3-21
Temperature Sensor 3-21
CHAPTER 4Mounting the Router 4-1
Router Mounting Kit 4-1
Mounting Kit Contents 4-1
Prepare to Mount the Router 4-2
Materials and Tools You Supply 4-3
Router Orientation When Mounting 4-3
General Safety Information for Mounting 4-3
Mounting Instructions 4-4
Attach the Mounting Bracket to the Router 4-4
Mount the Router on a DIN Rail 4-6
Mount the Router on a Wall 4-7
Ground the Router 4-8
CHAPTER 5Connecting the Router to Power 5-1
Before You Begin 5-1
Verify Router Hardware Readiness 5-1
Tools and Materials You Supply 5-2
EMC Class A Notices and Warnings (US and Canada) 5-2

Contents
v
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
Class A Notice for FCC 5-2
Class A Notice for Canada 5-3
Safety Information 5-3
AC Power Connection Information 5-4
Router Power Source Input Terminals 5-4
Electrical Wire Color Codes 5-5
Terminal Blocks and Mating Connectors for Power Input Wiring 5-6
Connect to AC Power 5-7
Verify AC Power Connection 5-9
Connect to DC Power (Optional) 5-9
Power Cycling the Router 5-10
Accessing the Buttons 5-10
CHAPTER 6Making Network Connections 6-1
Before Installing 6-1
Installation Site Preparation 6-1
Installation Safety Information 6-2
Connecting the Router to Power 6-2
Preventing Electrostatic Discharge Damage 6-2
Cabling Guidelines 6-2
Basic Network Connections 6-2
Connect to the Ethernet Network 6-3
Connecting the Ethernet Ports 6-3
Connecting the SFP Ports 6-4
Verify Ethernet Connection with System Software CLI 6-6
Additional Router Connections 6-7
Connecting the Console Port 6-8
About 6-8
Connecting 6-8
Related Information 6-9
Connecting the Serial Port 6-9
About 6-9
Connecting 6-9
Related Information 6-9
Connecting the USB Port 6-10
About 6-10
Connecting 6-10
Related Information 6-10
Connecting the Alarm Port 6-11

Contents
vi
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
About 6-11
Connecting 6-11
Related Information 6-11
SD Flash Memory Module Card 6-12
Installing Modules and Antennas 6-13
Related Information 6-13
CHAPTER 7About Connected Grid Modules 7-1
Installing or Replacing Modules 7-1
Installing Modules in the Router 7-1
Preparing to Install Modules 7-2
Installation Warning Statements 2
Module Installation Locations 7-2
Install Modules 7-3
Remove Modules 7-4
Where to Find Additional Module Information 7-4
CHAPTER 8About Connected Grid Antennas 8-1
Router Antennas Overview 8-1
GPS Antenna 8-2
WiFi Antenna 8-4
Connected Grid Module Antennas 8-4
Installing or Replacing Module Antennas 8-5
Where to Find Antenna Installation Information 8-5
Antenna Specifications 8-6
GPS Antenna Specifications 8-6
WiFi Antenna Specifications 8-7
CHAPTER 9Using the SD Flash Memory Module 9-1
SD Card Overview 9-1
Supported SD Cards 9-2
Accessing the SD Card 9-2
Inserting the SD Card 9-2
Online Insertion and Removal (OIR) 9-3
Safety Warnings 9-3
Preventing Electrostatic Discharge Damage 9-3
Tools You Supply 9-3
Removing and Inserting the SD Card 9-3

Contents
vii
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
SD Card Status 9-5
SD Card LED 9-5
Related Commands 9-6
CHAPTER 10 Router LED Locations and States 10-1
Rear Panel LED Locations 10-2
Power Supply LED 10-2
SYS LED – System Status 10-3
ACT LED – System Activity 10-3
WIFI LED – WiFi Link Status 10-3
GPS LED – GPS Link Status 10-3
CONSOLE LED – Console Port Status 10-4
ALM LEDS – Alarm Port Status 10-4
Ethernet LEDs – Network Links Status 10-4
SFP LEDs – SFP Port States 10-5
GE LEDs – Gigabit Ethernet Port States 10-5
FE LEDs – Fast Ethernet Port States 10-5
SD Card LED Location 10-6
SD LED – SD Card Status 10-6
Related Commands 10-6
show led 10-7
APPENDIX AStarting a Router Terminal Session A-1
Before You Begin A-1
About the Console Port A-1
Console Port Settings A-1
Using the Ctrl-C Command A-1
Connecting to the Console Port with Microsoft Windows A-2
Connecting to the Console Port with Mac OS X A-2
Connecting to the Console Port with Linux A-3
APPENDIX BConnector and Cable Specifications B-1
Connector Specifications B-1
Alarm Port B-1
Console Port B-2
Combo Ports B-2
Copper Interface—Combination Port (SFP and GE Ethernet) B-2

Contents
viii
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
SFP Ports B-3
SFP Interface—Combination Port (SFP and GE Ethernet) B-3
Serial Port B-4
Power Connectors B-4
Cable and Adapter Specifications B-4
SFP Cable B-4

CHAPTER
1-1
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
1
Unpacking the Router
This chapter includes instructions about how to unpack the Cisco 1120 Connected Grid Router and
describes the items that ship with the router. This chapter includes the following sections:
•Unpacking the Router, page 1-1
•Router Package Contents, page 1-2
Unpacking the Router
Tip When you unpack the router, do not remove the foam blocks attached to antennas and antenna
connectors. The foam protects the antennas and connectors during installation.
Follow these steps to unpack the router:
Step 1 Open the shipping container and carefully remove the contents.
Step 2 Return all packing material to the shipping container, and save it.
Step 3 Ensure that all items listed in the section Router Package Contents, page 1-2 are included in the
shipment. If any item is damaged or missing, notify your authorized Cisco sales representative.

1-2
Cisco 1120 Connected Grid Router Hardware Installation Guide
OL-26438-02
Chapter 1 Unpacking the Router
Router Package Contents
Router Package Contents
Your router kit contains the items listed in Table 1-1.
Table 1-1 Router Package Contents
Qty. Item Description
1 Cisco 1120 Connected Grid Router Router enclosure with the following components installed:
•Connected Grid Modules (1 to 2, depending on configuration ordered)
with required antennas
•1-GB SD Flash Memory Module
•AC power supply (integrated)
1 DIN Rail Mounting Kit Includes:
•DIN rail mounting bracket
•All required hardware to attach bracket to router
2 Power connectors adapters Use these mating connectors for wiring the router power connectors
1 User Documentation Kit Includes:
•Read Me First card
•Regulatory Compliance and Safety Information document