Cisco IE 4010 Manual

Cisco IE 4010 Switch Hardware Installation Guide
First Published: 2016-09-01
Last Modified: 2023-07-28
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

©2016–2023 Cisco Systems, Inc. All rights reserved.

CONTENTS
Product Overview 1
CHAPTER 1
Switch Models 1
Cable Side 2
10/100/1000 PoE/PoE+ Ports (Downlinks) 3
Alarms 4
Mini USB Port 4
SD Flash Memory Card 4
Display Mode Button 5
Power-Input Terminal 5
100/1000 SFP Ports 5
Console Ports 5
Switch Panel LEDs 6
Port LEDs 7
Display Mode Button 9
Power-Supply Module LEDs 10
Alarm LEDs 10
SD Flash Memory Card LED 10
USB LED 11
System LED 11
Power-Supply Side 11
Power-Supply Side LEDs 12
Power Supply Features 13
Management Options 13
Network Configurations 14
Switch Installation 15
CHAPTER 2
Cisco IE 4010 Switch Hardware Installation Guide
iii

Warnings 15
Installation Guidelines 17
Verifying Switch Operation 17
Installing the Switch 17
Rack-Mounting 18
Attaching Brackets for 19-Inch Racks 18
Attaching Brackets for 19-Inch Racks for IP-30 Compliance (Optional) 19
Attaching Brackets for 23-Inch Racks 21
Attaching Brackets for ETSI Racks 23
Rack-Mounting the Switch 24
Wall-Mounting 24
Attaching Brackets 26
Attaching Brackets for IP-30 Compliance (Optional) 27
Wall-Mounting the Switch 27
After the Switch is Mounted on the Wall 28
Installing and Removing SFP Modules 28
Installing SFP Modules 28
Connecting to SFP Modules 31
Removing SFP Modules 33
Replacing the SD Flash Memory Card 33
Connecting Devices to the Ethernet Ports 34
Where to Go Next 35
Power Supply Installation 37
CHAPTER 3
Power-Supply Modules 37
Power-Supply Module Installation 39
Installation Guidelines 39
Installing a Power-Supply Module 39
Equipment That You Need 40
Grounding the Switch 40
Installing the Power-Supply Module in the Switch 42
Installing the DC Power Supply in the Switch 43
Wiring the Power Source 44
Removing the Power-Supply Module 48
Cisco IE 4010 Switch Hardware Installation Guide
iv
Contents

Troubleshooting 49
CHAPTER 4
Diagnosing Problems 49
Switch Boot Fast 49
Switch LEDs 49
Switch Connections 49
Bad or Damaged Cable 50
Ethernet and Fiber-Optic Cables 50
Link Status 50
10/100/1000 Port Connections 50
SFP Module 51
Interface Settings 51
Ping End Device 51
Spanning Tree Loops 51
Switch Performance 51
Speed, Duplex, and Autonegotiation 51
Autonegotiation and Network Interface Cards 52
Cabling Distance 52
Resetting the Switch 52
How to Recover Passwords 53
Finding the Switch Serial Number 53
Hazardous Location Installation Information 55
CHAPTER 5
Hazardous Area Installation Warnings 55
North American Hazardous Location Approval 57
EMC Environmental Conditions for Products Installed in the European Union 58
Hazardous Locations Standards 58
Cable and Connectors 61
CHAPTER 6
Connector Specifications 61
10/100/1000 Ports 61
SFP Module Connectors 61
Console Port 62
Alarm Port 63
Cisco IE 4010 Switch Hardware Installation Guide
v
Contents

Cables and Adapters 63
SFP Module Cables 63
Console Port Adapter Pinouts 63
Configuring the Switch with the CLI Setup Program 65
CHAPTER 7
Accessing the CLI Through Express Setup 65
Required Equipment 65
Express Setup Procedure 66
Accessing the CLI Through the Console Port 70
RJ-45 Console Port 70
USB Console Port 71
Installing the Cisco Microsoft Windows XP, 2000, Vista, 7, 8, and 10 USB Device Driver 72
Uninstalling the Cisco Microsoft Windows XP, 2000, Vista, 7, 8, and 10 USB Driver 73
Entering the Initial Configuration Information 73
IP Settings 74
Completing the Setup Program 74
Technical Specifications 77
CHAPTER 8
Switch Specifications 77
Power-Supply Module Specifications 79
Alarm Ratings 79
Cisco IE 4010 Switch Hardware Installation Guide
vi
Contents

CHAPTER 1
Product Overview
The Cisco IE 4010 switch provides a rugged and secure switching infrastructure for harsh environments. It
is suitable for industrial Ethernet applications, including process manufacturing, utility substations, intelligent
transportation systems (ITSs), rail transportation, and other similar deployments.
In industrial environments, you can connect the switch to any Ethernet-enabled industrial communication
devices, including programmable logic controllers (PLCs), human-machine interfaces (HMIs), drives, sensors,
and input and output (IO) devices.
In utility substations the switch can connect to devices such as Intelligent Electronic Devices (IEDs), distributed
controllers, substation routers, Cisco IP Phones, Cisco Wireless Access Points, and other network devices
such as redundant substation switches.
For detailed specifications, see the IE 4010 Data Sheet.
This chapter contains the following sections:
•Switch Models, on page 1
•Cable Side, on page 2
•Power-Supply Side, on page 11
•Management Options, on page 13
Switch Models
Table 1: Switch Models
Power
Supplies
Default
Software
License
Copper
10/100/1000PoE/PoE+
Ports 1
SFP Fiber
Ports
UplinksTotal PortsModel
Support for 2
field-replaceable,
redundant AC
or DC power
supplies.
LAN Base2 12
(10/100/1000M)
12
(100/1000M
4 SFP
(100MB/1G)
28IE-4010-16S12P
Cisco IE 4010 Switch Hardware Installation Guide
1

Power
Supplies
Default
Software
License
Copper
10/100/1000PoE/PoE+
Ports 1
SFP Fiber
Ports
UplinksTotal PortsModel
Support for 2
field-replaceable,
redundant AC
or DC power
supplies.
LAN Base24
(10/100/1000M)
—4 SFP
(100MB/1G)
28IE-4010-4S24P
1All copper Gigabit Ethernet interfaces support speed negotiation to 10/100/1000 mbps and duplex
negotiation.Ethernet 4010 Series.
Note
2Can be upgraded to IP Services at a fee. IP Services License Product Numbers are the following:
L-IE4000-RTU= (Electronic SW License for IE4000 Switches)
Note
Cable Side
Figure 1: Cisco IE-4010-16S12P Cable-Side View
Table 2:
LEDs1
Express Setup button2
Twelve 10/100/1000 PoE/PoE+ Ports (Downlinks)3
Alarm port4
USB (mini-Type B) console port5
Power-input terminal6
Cisco IE 4010 Switch Hardware Installation Guide
2
Product Overview
Cable Side

Flash memory card slot7
Display mode button8
Twelve 100/1000 SFP Ports9
Console port10
For detailed information see Port LEDs.
10/100/1000 PoE/PoE+ Ports (Downlinks)
You can set the 10/100/1000 ports on the switch to operate in any combination of half duplex, full duplex, or
10 or 100 Mb/s. You can set the ports for speed and duplex autonegotiation. The default setting is autonegotiate.
When set for autonegotiation, the switch determines the speed and duplex settings of the attached device and
advertises its own capabilities. If the connected device also supports autonegotiation, the switch negotiates
the best connection (the fastest line speed that both devices support and full-duplex transmission if the attached
device supports it) and configures itself accordingly. In all cases, the attached device must be within 328 feet
(100 meters).
Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are
made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection
methods, unless the exposed metal parts are located within a restricted access location and users and service
people who are authorized within the restricted access location are made aware of the hazard. A restricted
access area can be accessed only through the use of a special tool, lock and key or other means of security.
Statement 1072
Warning
The 10/100/1000 PoE ports on the Cisco IE-4010 switches provide PoE support for devices that are compliant
with IEEE 802.3af/802.3at. The Cisco prestandard PoE is also supported for Cisco IP Phones and Cisco
Aironet Access Points. The PoE ports on the switch deliver up to 30 W of PoE+ power. All twelve ports are
PoE ports and can be assigned a port priority.
When both power-supply modules are installed, the system has enough power to support all twelve ports as
PoE ports. The maximum available PoE power is 200W.
With one power module installed, the maximum available PoE power is 80W. In case one power-supply
modules fails, the power to the low priority PoE ports is dropped, while power to the high priority PoE ports
remains uninterrupted.
On a per-port basis, you control whether or not a port automatically provides power when an IP phone or an
access point is connected.
The 10/100/1000 PoE ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328
feet (100 meters). The 100BASE-TX and 1000BASE-T traffic requires CA5, CAT5e, or CAT6 unshielded
twisted pair (UTP) cable. The 10BASE-T traffic can use CAT3 or CAT4 UTP cable.
For information about configuring and monitoring PoE ports, see the switch software configuration guide on
Cisco.com.
For information about port connections and port specifications, see Connecting Devices to the Ethernet Ports,
on page 34.
Cisco IE 4010 Switch Hardware Installation Guide
3
Product Overview
10/100/1000 PoE/PoE+ Ports (Downlinks)

The output of the PoE circuit has been evaluated as a Limited Power Source (LPS) per IEC 60950-1.
Note
Alarms
The switch has four alarm inputs and one alarm output.
Alarm Input
The alarm input is a dry-contact alarm port. You can connect up to four alarm inputs from devices, such as a
door, a temperature gauge, or a fire alarm, to the alarm port. You can use the CLI to set the alarm severity to
minor, or major. An alarm generates a system message and turns on an LED. See the ??? for the LED
descriptions.
Alarm Output
The alarm output can be configured as a major alarm. Output alarms often control an external alarm, such as
a bell or a light. To connect an external alarm device to the relay, you connect two relay contact wires to
complete the electrical circuit. See for information on the alarm pinouts. see the Alarm Port, on page 63.
Mini USB Port
The 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors. They are not compatible. Use
only the 5-pin mini-Type B.
Note
Figure 2: USB Mini-Type B Port
The configurable inactivity timeout reactivates the RJ-45 console port if the USB console port is activated,
but no input activity occurs on it for a specified time period. When the USB console port deactivates due to
a timeout, you can restore its operation by disconnecting and reconnecting the USB cable. For information
on using the CLI to configure the USB console interface, see the switch software guide.
SD Flash Memory Card
The switch supports a flash memory card that makes it possible to replace a failed switch without reconfiguring
the new switch. The slot for the flash memory card is on the front of the switch. The flash card is hot swappable
and can be accessed on the front panel in non hazardous locations only. A cover protects the flash card and
holds the card firmly in place. The cover is hinged and closed with a captive screw. This prevents the card
from coming loose and protects against shock and vibration.
For more information on inserting and removing the flash memory card, see Power-Supply Side, on page 11.
Cisco IE 4010 Switch Hardware Installation Guide
4
Product Overview
Alarms