Cisco Catalyst 4500 Series Installation and operation manual

Corporate Headquarters:
Copyright © 2002. Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Installation Note for Fan Tray Assemblies in
Catalyst 4500 Series Switches
Fan Assembly Overview
Note For complete environmental specifications, including airflow requirements, refer to Appendix A,
“Specifications,” in the Catalyst 4500 Series Installation Guide. The guide is available online at
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/installation/guide/78-14409-08/
4500inst.html
The system fan assembly provides cooling air for the internal chassis components. The fan assembly is
a tray of fans that you can insert and remove from the chassis while the system is on line. The
Catalyst 4503 fan assembly has two fans, the Catalyst 4506 fan assembly has four fans, and the
Catalyst 4507R fan assembly has six fans. The fans draw in fresh air from one side and exhaust air on
the other side. Catalyst 4503 airflow is shown in Figure 1. Catalyst 4506 airflow is shown in Figure 2.
Catalyst 4507R airflow is shown in Figure 3.
Caution You must install module filler plates on unused switching module slots to ensure proper airflow.
Caution Removing and replacing fan trays produced between September 2002 and November 2002 might require
rebooting the switch in a Catalyst 4506 switch with a Supervisor Engine III or Supervisor Engine IV and
in a Catalyst 4507R switch with Supervisor Engine IV. Starting in December 2002, Cisco added a white
strip on the bottom of the fan tray label to identify improved fan trays that do not have this limitation.

2
Installation Note for Fan Tray Assemblies in Catalyst 4500 Series Switches
78-15335-01
Fan Assembly Overview
Figure 1 Catalyst 4503 Airflow
Figure 2 Catalyst 4506 Airflow
1
13
1
13
1
13
1
13
77981
4506
UPLINK1 UPLINK2
ACTIVE
LINEACTIVELINEACTIVE
RESET
UTILIZATION
STATUS
4503
WS-X4515SUPERVISORENGINEIV
1%100%
CONSOLE
LINK
EJECT
FLASH
10/100
MGT
Fan assembly
1
13
1
13
1
13
1
13
1
13
1
13
77511
4506
UPLINK1 UPLINK2
ACTIVE
LINEACTIVELINEACTIVE
RESET
UTILIZATION
STATUS
WS-X4515SUPERVISORENGINEIV
1%100%
CONSOLE
LINK
EJECT
FLASH
10/100
MGT
Fan assembly

3
Installation Note for Fan Tray Assemblies in Catalyst 4500 Series Switches
78-15335-01
Removing and Replacing the Chassis Fan Assembly
Figure 3 Catalyst 4507R Airflow
Removing and Replacing the Chassis Fan Assembly
This section describes how to remove and install the chassis fan assembly for the Catalyst 4500 series
switches. See Figure 4 for the Catalyst 4503 system fan assembly, Figure 5 for the Catalyst 4506 system
fan assembly, and Figure 6 for the Catalyst 4507R system fan assemblies.
Required Tools
You will need a Phillips screwdriver for the following two procedures.
68111
Fan assembly
WS-X4448-GB-RJ45
STATUS
12
11
10
9
8
7
6
5
4
3
2
1
14
13
16
15
28
27
26
25
24
23
22
21
20
19
18
17
30
29
32
31
44
43
42
41
40
39
38
37
36
35
34
33
46
45
48
47
10/100BASE-TX
ETHERNET
MULTI-SPEED
GIGABITETHERNET
SWITCHINGMODULE
WS-X4448-GB-RJ45
STATUS
12
11
10
9
8
7
6
5
4
3
2
1
14
13
16
15
28
27
26
25
24
23
22
21
20
19
18
17
30
29
32
31
44
43
42
41
40
39
38
37
36
35
34
33
46
45
48
47
10/100BASE-TX
ETHERNET
MULTI-SPEED
GIGABITETHERNET
SWITCHINGMODULE
1
STATUS
WS-X4412-2GB-TX
234567891011 1217
1
STATUS
WS-X4412-2GB-TX
2345678910111217
1
STATUS
WS-X4412-2GB-TX
2345678910111217
UPLINKUPLINK
CONSOLE 10/100
BASE-TX
STATUS
UPLINKUPLINK
CONSOLE 10/100
BASE-TX
STATUS

4
Installation Note for Fan Tray Assemblies in Catalyst 4500 Series Switches
78-15335-01
Removing and Replacing the Chassis Fan Assembly
Figure 4 Catalyst 4503 System Fan Assembly
Figure 5 Catalyst 4506 System Fan Assembly
1
13
1
13
1
13
1
13
79172
UPLINK1 UPLINK2
ACTIVE
LINEACTIVELINEACTIVE
RESET
UTILIZATION
STATUS
4503
WS-X4515 SUPERVISOR ENGINE IV
1%100%
CONSOLE
LINK
EJECT
FLASH
10/100
MGT
Captive installation
screws
Fan assembly
4503
1
13
1
13
1
13
1
13
1
13
1
13
79171
UPLINK1 UPLINK2
ACTIVE
LINEACTIVELINEACTIVE
RESET
UTILIZATION
STATUS
WS-X4515SUPERVISORENGINEIV
1%100%
CONSOLE
LINK
EJECT
FLASH
10/100
MGT
Captive installation
screws
Fan assembly

5
Installation Note for Fan Tray Assemblies in Catalyst 4500 Series Switches
78-15335-01
Removing and Replacing the Chassis Fan Assembly
Figure 6 Catalyst 4507R System Fan Assembly
Removing the Fan Assembly
Caution When changing fan assemblies, try to keep changeover times to under a minute. Never operate the
system for an extended period if the fan assembly is removed or if it is not functioning properly. An
overtemperature condition can cause severe equipment damage or an unscheduled system shutdown.
Follow these steps to remove the existing chassis fan assembly:
Step 1 Loosen the two captive installation screws on the fan assembly by turning them counterclockwise.
Step 2 Grasp the fan assembly with both hands and pull it outward; wiggle it if necessary to unseat it from the
backplane. Slide it out of the chassis and put it someplace where it will not be dropped or stepped on.
68116
Captive installation
screws
Fan assembly
WS-X4448-GB-RJ45
STATUS
12
11
10
9
8
7
6
5
4
3
2
1
14
13
16
15
28
27
26
25
24
23
22
21
20
19
18
17
30
29
32
31
44
43
42
41
40
39
38
37
36
35
34
33
46
45
48
47
10/100BASE-TX
ETHERNET
MULTI-SPEED
GIGABITETHERNET
SWITCHINGMODULE
WS-X4448-GB-RJ45
STATUS
12
11
10
9
8
7
6
5
4
3
2
1
14
13
16
15
28
27
26
25
24
23
22
21
20
19
18
17
30
29
32
31
44
43
42
41
40
39
38
37
36
35
34
33
46
45
48
47
10/100BASE-TX
ETHERNET
MULTI-SPEED
GIGABITETHERNET
SWITCHINGMODULE
1
STATUS
WS-X4412-2GB-TX
2345678910 1112 17
1
STATUS
WS-X4412-2GB-TX
23456789101112 17
1
STATUS
WS-X4412-2GB-TX
2345678910111217
UPLINKUPLINK
CONSOLE 10/100
BASE-TX
STATUS
UPLINKUPLINK
CONSOLE 10/100
BASE-TX
STATUS

6
Installation Note for Fan Tray Assemblies in Catalyst 4500 Series Switches
78-15335-01
Removing and Replacing the Chassis Fan Assembly
Installing the Fan Assembly
Follow these steps to install the new fan assembly:
Step 1 Hold the fan assembly with the fans facing to the right.
Step 2 Place the fan assembly into the fan assembly bay so it rests on the chassis, and then lift the fan
assembly up slightly, aligning the top and bottom guides.
Step 3 Slide the fan assembly into the chassis until the two captive installation screws make contact with the
chassis.
Step 4 Using a screwdriver, tighten the two captive installation screws by turning them clockwise.
Warning When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the
fan blades completely stop before you remove the fan tray.
Waarschuwing
Houd tijdens het verwijderen van de ventilator de handen en vingers uit de buurt van de draaiende
ventilatorschoepen. Laat de ventilatorschoepen volledig tot stilstand komen alvorens de ventilator
te verwijderen.
Varoitus
Pidä kädet ja sormet pois tuulettimen pyörivistä siivistä tuuletinalustaa poistaessasi. Anna
tuulettimen siipien pysähtyä kokonaan ennen kuin irrotat tuuletinalustan.
Attention
Lors du retrait du plateau du ventilateur, veillez à ce que vos mains et doigts restent à l’écart des
pales en rotation du ventilateur. Attendez que les pales du ventilateur soient parvenues à une
immobilité complète avant de retirer le plateau du ventilateur.
Warnung
Beim Herausnehmen des Lüfterkastens Hände und Finger von den sich drehenden Gebläseflügeln
fern halten. Vor Herausnehmen des Gebläsekastens warten, bis die Gebläseflügel völlig zum
Stillstand gekommen sind.
Avvertenza
Quando si toglie il vano della ventola, fare attenzione che le mani e le dita non vengano in contatto
con la ventola in movimento. Attendere che la ventola si fermi completamente prima di togliere il
vano.
Advarsel
Når du fjerner viftedekselet, hold hender og fingre borte fra de roterende viftebladene. La
viftebladene stanse helt før du fjerner viftedekselet.
Aviso
Mantenha as suas mãos e dedos afastados das lâminas em movimento da ventoinha, ao retirar a
respectiva bandeja. Deixe as lâminas da ventoinha parar completamente antes de retirar a bandeja.
¡Advertencia!
Cuando quite la bandeja del abanico, mantenga las manos y los dedos alejados de las aspas en
movimiento. Deje que las aspas se detengan completamente antes de quitar la bandeja del abanico.
Varning!
Håll händer och fingrar borta från de roterande fläktbladen när du tar av fläktskyddet. Låt fläkten
stanna helt innan du tar av fläktskyddet.

7
Installation Note for Fan Tray Assemblies in Catalyst 4500 Series Switches
78-15335-01
Related Documentation
Verifying the Installation
Note To check the operation of the fans, you need to power up the chassis.
Follow these steps to verify that the new fan assembly was installed correctly:
Step 1 Listen for the fans; you should immediately hear them operating. If you do not hear them, ensure that
the fan assembly is inserted completely in the chassis and that the faceplate is flush with the switch
back panel.
Step 2 If after several attempts the fans do not operate, or if you experience trouble with the installation (for
instance, if the captive installation screws do not align with the chassis holes), contact the Cisco
Technical Assistance Center (TAC) for assistance.
Related Documentation
For other installation and configuration information, refer to this publication:
•Catalyst 4500 Series Installation Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence,
Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are
service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP,
CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo,
Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive,
HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace,
MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare,
SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo
are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0812R)
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.

8
Installation Note for Fan Tray Assemblies in Catalyst 4500 Series Switches
78-15335-01
Obtaining Documentation and Submitting a Service Request