Cisco Nexus 9332D-GX2B Manual

Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation
Guide
First Published: 2021-10-18
Last Modified: 2021-12-13
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS REFERENCED IN THIS DOCUMENTATION ARE SUBJECT TO CHANGE WITHOUT NOTICE.
EXCEPT AS MAY OTHERWISE BE AGREED BY CISCO IN WRITING, ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS DOCUMENTATION ARE
PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED.
The Cisco End User License Agreement and any supplemental license terms govern your use of any Cisco software, including this product documentation, and are located at:
http://www.cisco.com/go/softwareterms.Cisco product warranty information is available at http://www.cisco.com/go/warranty. US Federal Communications Commission Notices are found
here http://www.cisco.com/c/en/us/products/us-fcc-notice.html.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any products and features described herein as in development or available at a future date remain in varying stages of development and will be offered on a when-and if-available basis. Any
such product or feature roadmaps are subject to change at the sole discretion of Cisco and Cisco will have no liability for delay in the delivery or failure to deliver any products or feature
roadmap items that may be set forth in this document.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based
on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language
that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com
go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (1721R)
©2021 Cisco Systems, Inc. All rights reserved.

CONTENTS
Overview 1
CHAPTER 1
Overview 1
Preparing the Site 5
CHAPTER 2
Temperature Requirements 5
Humidity Requirements 5
Altitude Requirements 5
Dust and Particulate Requirements 6
Minimizing Electromagnetic and Radio Frequency Interference 6
Shock and Vibration Requirements 7
Grounding Requirements 7
Planning for Power Requirements 7
Airflow Requirements 8
Rack and Cabinet Requirements 9
Clearance Requirements 10
Installing the Chassis 11
CHAPTER 3
Safety 11
Installation Options with Rack-Mount Kits 12
Airflow Considerations 12
Installation Guidelines 12
Unpacking and Inspecting the Switch 14
Installing the Switch Using the NXK-ACC-KIT-1RU Rack-Mount Kit 14
Grounding the Chassis 18
Starting the Switch 19
Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
iii

Connecting the Switch to the Network 23
CHAPTER 4
Overview of Network Connections 23
Connecting a Console to the Switch 23
Creating the Initial Switch Configuration 25
Setting Up the Management Interface 26
Connecting Interface Ports to Other Devices 27
Replacing Components 29
CHAPTER 5
Replacing a Fan Module 29
Removing a Fan Module 29
Installing a Fan Module 30
Replacing a Power Supply Module 30
Removing an AC Power Supply 30
Installing an AC Power Supply 31
Rack Specifications 33
APPENDIX A
Overview of Racks 33
General Requirements for Cabinets and Racks 33
Requirements Specific to Standard Open Racks 34
Requirements Specific to Perforated Cabinets 34
Cable Management Guidelines 34
System Specifications 35
APPENDIX B
Environmental Specifications 35
Switch Dimensions 35
Switch and Module Weights and Quantities 36
Transceiver and Cable Specifications 36
Switch Power Input Requirements 36
Power Specifications 36
1500-W AC Power Supply Specifications 37
Power Cable Specifications 37
Power Cables for NXA-PAC-1500W Power Supplies 37
Regulatory Standards Compliance Specifications 38
Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
iv
Contents

LEDs 41
APPENDIX C
Switch Chassis LEDs 41
Fan Module LEDs 42
Power Supply LEDs 42
Additional Kits 43
APPENDIX D
Rack Mount Kit NXK-ACC-KIT-1RU 43
Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
v
Contents

Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
vi
Contents

CHAPTER 1
Overview
•Overview, on page 1
Overview
The Cisco Nexus 9332D-GX2B switch (N9K-C9332D-GX2B) is a 1-rack unit (RU), fixed-port switch designed
for deployment in data centers.
This switch includes the following ports:
• 400-Gigabit QSFP-DD ports (32)
• 10-Gigabit SFP+ ports (2)
• Management ports (one 10/100/1000BASE-T port and one SFP port)
• Console port (RS-232)
• USB port
• If MACsec is enabled on 8 ports, then you can not use high powered (>12W) optics.
• If MACsec is enabled on 4 ports, then you can use 4 ports with high powered (>12W) optics.
• If no MACsec is enabled, then you can use 8 ports with high powered (>12W) optics.
Note
This switch includes the following user-replaceable components:
• Fan modules (6) with the following airflow choices:
• Port-side intake fan module with burgundy coloring (NXA-SFAN-35CFM-PI)
• Power supply modules (two—One for operations and one for redundancy [1+1]) with the following
choices:
• 1500-W port-side intake AC power supply with burgundy coloring (NXA-PAC-1500W-PI)
Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
1

All fan modules and power supplies must use the same airflow
direction.
Note
The following figure shows the switch features on the port side of the chassis.
400-Gigabit QSFP-DD
ports (32)
3LEDs1
10-Gigabit SFP+ ports (2)2
To determine which transceivers, adapters, and cables are support this switch, see the Cisco Transceiver
Modules Compatibility Information document.
The following figure shows the switch features on the power supply side of the chassis.
Management port (RJ45)4Power supply modules (1
or 2) (AC power supplies
shown) with slots
numbered 1 (left) and 2
(right)
1
Management port (SFP)5Fan modules (6) with slots
numbered from 1 (left) to
6 (right)
2
USB port6Console port3
The following figure shows the side of the chassis.
Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
2
Overview
Overview

Grounding pad2Screw holes for mounting
brackets
1
The fan and power supply modules are field replaceable. You can replace one fan module or one power supply
module during operations so long as the other modules are installed and operating. If you have only one power
supply installed, you can install the replacement power supply in the open slot before removing the original
power supply.
All fan and power supply modules must have the same direction of airflow. Otherwise, the switch can overheat
and shut down.
Note
If the switch has port-side intake airflow (burgundy coloring for fan modules), you must locate the ports in
the cold aisle. If the switch has port-side exhaust airflow (blue coloring for fan modules), you must locate the
ports in the hot aisle. If you locate the air intake in a hot aisle, the switch can overheat and shut down.
Caution
Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
3
Overview
Overview

Cisco Nexus 9332D-GX2B NX-OS Mode Switch Hardware Installation Guide
4
Overview
Overview