Citronic MP-X10 User manual

VIRTUAL 7 PRO MAP MANUAL
Version 1.0

CITRONIC MP-X10
Initial Setup
1. Before making or changing the connections, switch off the power and disconnect the
power cord from the AV outlet.
. We recommend to use high quality shielded audio cables when connecting input/output
devices as it makes a huge difference in sound reproduction quality.
3. o not use excessively long cables. Be sure the plugs and jacks are securely fastened.
Loose connections cause hum, noise or intermittence that can damage your speakers.
4. Connecting to a computer – the controller will be automatically recognised by both
Windows based PC / Laptops operating Windows XP SP2 or later and MAC O/S 10.4 or
later as a generic MI I controller without the need to install drivers (Note the B
software only works with Windows based operating computers). You can then use any J
software with MI I mapping features to program in the functions to operate on screen
(See Page 20)
PC Requirements:
Intel® Pentium® 4 or AM Athlon™ XP
1024x768 resolution
irectX compatible soundcard
512MB RAM
50MB free on the hard drive
Windows XP Home
MAC Requirements:
Intel® Pentium
Mac OS X v10.5
1024x768 resolution
CoreAudio compatible soundcard
1024mb RAM
50mb free hard drive

VIRTUAL DJ PRO Setup
1) Connect the supplied USB cable (or any A to B USB lead that is version 2.0 or above) to
the USB MI I connection on the rear of the MPX10 unit.
2) Connect the USB A connection to a PC or Laptop and turn the power on
3) Ensure the channel outputs on the MPX10 are both set to “PC”
4) You computer should detect the MPX10 as a sound card and Generic USB MI I controller

5) Move the files to the following locations before you start V J PRO:
For Windows
a. MPX10.XML file to MY OCUMENTS/Virtual J/ evices
b. Citronic MP-X10 mapping.xml file to MY OCUMENTS/Virtual J/Mapper
For MAC
a. MPX10.XML file to: /users/YOURNAME/ ocuments/Virtual J/ evices
b. Citronic MP-X10 to: /users/YOURNAME/ ocuments/Virtual J/Mappers
6) Load Virtual J 7 PRO.
7) Click on “CONFIG” button to open the options and setup the sound card as shown below:
Press APPLY followed by OK.
You should now be ready to use your MPX10 on Virtual J Pro. The device can work in 2 or 4
deck mode. To use 4 deck mode press the SOURCE button to switch between decks. You can
also switch one side of the deck to PC and operate the other directly from the player:

OPERATION GUIDE:
The MPX10 has the same operation as when in stand alone mode: See the layout map at the
end of this guide which indicates what each button does. There is however some added
features which we included to enhance the use of the software and controller:
VDJ Function button:
The Function button on the controller puts the MPX10 in to one of three modes which effect
the operation of other buttons to give you easy access to more exciting features:
Toggle through each mode by pressing the button continuously.
Function 1: Normal mode (LED OFF)
Track ial: Turn to toggle through the tracks on the playlist and press to load the track
into the eck.
Folder ial: Turn to toggle through folders and press to open them.
Hot Cues: Press to set and recall Hot cue points in a song. To delete hold down CLEAR
and press the Hot cue button you wish to delete.
X Button: When used in combination with the Jog wheel will adjust parameter 1 of the
digital effects (EG: Flanger, Echo… etc)
Y Button: When used in combination with the Jog wheel will adjust parameter 2 of the
digital effects (EG: Flanger, Echo… etc)

Function : Sample mode (LED ON)
Track ial: Rotate to alter the volume of the selected sample. Press to activate or
deactivate the sample.
Folder ial: Rotate to alter the shutter length of the selected sample. Press to activate
deactivate the sample
Hot Cues: Used to activate / deactivate samples loaded in slots 1 - 4
X Button: When used in combination with the JOG wheel will increase or decrease the
volume of the playing sample
Y Button: When used in combination with the JOG wheel will increase or decrease the
shutter length of the playing sample.
Function 3: Loop mode (LED Flashing)
Track ial: Rotate to lengthen or shorten the Auto loop length press to activate or
deactivate.
Folder ial: Rotate to move the loop along forward or backwards 1 beat at a time
Hot Cues: Press the following buttons to set the preset auto loop beat:
1 = 1 beat
2 = 2 beats
3 = 4 beats
4 = 8 beats
X Button: When used in combination with the JOG wheel to adjust the end of the loop
accurately.
Y Button: When used in combination with the JOG wheel to adjust the IN point of the
loop. NOTE this will also move the out point along.
The microphone channel will not work as a MI I input through Virtual J Pro but will continue
to work independently through the MP-X10 unit when in PC mode.

CONTROLLER OPERATIONS

FOR MORE INFORMATION ON CITRONIC PRODUCTS VISIT
WWW.CITRONIC.COM
Copyright protected by Citronic UK